Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › 2019.09–2020.08
BM32H0E _V1 General _060351 INTRODUCTION _0295857 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  REPAIR PROCEDURE OF HEADLIGHT ASSEMBLY  


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

If the installation area of the headlight assembly is damaged, use a supply retainer for a low-cost repair.

·

Ensure that the headlight assembly is not damaged.



INSTALL UPPER HEADLIGHT PROTECTOR RETAINER (for Triple Beam Headlight)


a.
E351129

Cut off the part shaded in the illustration and sand smooth with sandpaper.

HINT:

After cutting off the part, place the upper headlight protector retainer against the bosses and gradually file away the old bracket if it interferes with the installation of a supply retainer.



b.
E351130

Install the upper headlight protector retainer with the screw.



INSTALL UPPER NO. 2 HEADLIGHT PROTECTOR RETAINER (for Triple Beam Headlight)


a.
E426115

Cut off the part shaded in the illustration and sand smooth with sandpaper.

HINT:

After cutting off the part, place the upper No. 2 headlight protector retainer against the bosses and gradually file away the old bracket if it interferes with the installation of a supply retainer.



b.
E395006C01
0.656,1.229 0.385,0.938 true 0.188,0.802 0.375,0.99 0.188,0.188 10 false *a

Cut off the part of the upper No. 2 headlight protector retainer as shown in the illustration.


c.
E426116

Install the upper No. 2 headlight protector retainer with the 2 screws.



INSTALL UPPER NO. 3 HEADLIGHT PROTECTOR RETAINER (for Triple Beam Headlight)


a.
E426117

Cut off the part shaded in the illustration and sand smooth with sandpaper.

HINT:

After cutting off the part, place the lower headlight protector retainer against the bosses and gradually file away the old bracket if it interferes with the installation of a supply retainer.



b.
E426118

Install the upper No. 3 headlight protector retainer with the 2 screws.



INSTALL UPPER HEADLIGHT PROTECTOR RETAINER (for Single Beam Headlight)


a.
E351129

Cut off the part shaded in the illustration and sand smooth with sandpaper.

HINT:

After cutting off the part, place the upper headlight protector retainer against the bosses and gradually file away the old bracket if it interferes with the installation of a supply retainer.



b.
E351130

Install the upper headlight protector retainer with the screw.



INSTALL UPPER NO. 2 HEADLIGHT PROTECTOR RETAINER (for Single Beam Headlight)


a.
E426120

Cut off the part shaded in the illustration and sand smooth with sandpaper.

HINT:

After cutting off the part, place the upper No. 2 headlight protector retainer against the bosses and gradually file away the old bracket if it interferes with the installation of a supply retainer.



b.
E395006C01
0.656,1.229 0.385,0.938 true 0.188,0.802 0.375,0.99 0.188,0.188 10 false *a

Cut off the part of the upper No. 2 headlight protector retainer as shown in the illustration.


c.
E426121

Install the upper No. 2 headlight protector retainer with the 2 screws.



INSTALL UPPER NO. 3 HEADLIGHT PROTECTOR RETAINER (for Single Beam Headlight)


a.
E426122

Cut off the part shaded in the illustration and sand smooth with sandpaper.

HINT:

After cutting off the part, place the lower headlight protector retainer against the bosses and gradually file away the old bracket if it interferes with the installation of a supply retainer.



b.
E426123

Install the upper No. 3 headlight protector retainer with the 2 screws.