SYSTEM CONTROL
The states of the theft deterrent system are as follows:
| State | Description | Theft Detection |
|---|---|---|
| Disarmed State | The theft deterrent system has not been set by the user. | Not possible |
| Arming Preparation State | This is the preparation state before the theft deterrent system becomes active (enters the armed state) when the system has been set by the user. | Not possible |
| Armed State | The theft deterrent system is active. (Theft can be detected.) | Possible |
| Alarm Sounding State | A theft attempt has been detected and the warning operation activates. | Possible |
The theft deterrent system activates as shown in the diagram above when one of the items in the table occurs in order to cause the system to enter the respective state.
| Condition | Item |
|---|---|
|
*1: Models with intrusion sensor (theft warning ultrasonic sensor) *2: Models with glass breakage sensor |
|
| (1) | In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·
With all doors and the engine hood closed, all doors are locked by wireless operation or the entry and start system. |
| (2) | Approximately 30 seconds elapse. |
| (3) | ·
The doors are unlocked by wireless operation or the entry and start system. ·
Any door is unlocked. ·
Any door is opened. ·
The engine switch is pushed. ·
The engine switch is turned to ON. ·
The battery is reconnected. |
| (4) | ·
The engine hood is opened when the engine hood is closed. ·
The battery is reconnected. ·
The intrusion sensor (theft warning ultrasonic sensor) detects movement within the vehicle.*1 ·
The glass breakage sensor detects that glass is broken.*2 ·
Any door is opened when all doors are closed. ·
Any door is unlocked when all doors are locked. ·
When 5 seconds or more have elapsed after the engine switch is pushed, the power source mode is changed from off to on (IG) without pressing the engine switch. ·
The engine hood is open. ·
Any door is opened. ·
The power source mode is on (IG).
|
| (5) | ·
The engine switch is turned to ON and the engine is running for more than approximately 2 seconds. ·
All doors are unlocked by wireless operation or the entry and start system. |
| (6) | After approximately 27.5 seconds, the alarm stops and approximately 5 seconds later the system returns to the armed state. |
| (7) | The open engine hood is closed with all the doors closed. |
| (8) | ·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
The engine switch is pushed. ·
The engine switch is turned to ON. ·
The battery is reconnected. ·
All doors are unlocked by wireless operation or the entry and start system. |
| (9) | In disarmed state 1, when the engine switch is off, the system state is switched if the following condition is met:
·
With all doors closed and the engine hood opened, all doors are locked by wireless operation or the entry and start system. |
| (10) | The engine hood is opened. |
| Condition | Item |
|---|---|
|
*1: Models with intrusion sensor (theft warning ultrasonic sensor) *2: Models with glass breakage sensor |
|
| (1) | In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·
With all doors and the engine hood closed, all doors are locked by wireless operation. |
| (2) | Approximately 30 seconds elapse. |
| (3) | ·
All doors are unlocked by wireless operation. ·
Any door is unlocked. ·
Any door is opened. ·
Key is in the key cylinder. ·
The ignition switch is turned to ON. ·
The battery is reconnected. |
| (4) | ·
The engine hood is opened when the engine hood is closed. ·
The battery is reconnected. ·
The intrusion sensor (theft warning ultrasonic sensor) detects movement within the vehicle.*1 ·
The glass breakage sensor detects that glass is broken.*2 ·
Any door is opened when all doors are closed. ·
Any door is unlocked when all doors are locked. ·
The engine hood is open. ·
Any door is opened. ·
The ignition switch is ON when the key is not in the key cylinder.
|
| (5) | ·
The ignition switch is turned to ON and the engine is running for more than approximately 2 seconds. ·
All doors are unlocked by wireless operation. |
| (6) | After approximately 27.5 seconds, the alarm stops and approximately 5 seconds later the system returns to the armed state. |
| (7) | The open engine hood is closed with all the doors closed. |
| (8) | ·
Any door is unlocked when all doors are locked. ·
Any door is opened. ·
Key is in the key cylinder. ·
The ignition switch is turned to ACC or ON. ·
The battery is reconnected. ·
All doors are unlocked by wireless operation. |
| (9) | In disarmed state 1, when the ignition switch is off, the system state is switched if the following condition is met when the key is not in the key cylinder:
·
With all doors closed and the engine hood opened, all doors are locked by wireless operation. |
| (10) | The engine hood is opened. |
FUNCTION
The theft deterrent system has the following functions:
| Function | Outline |
|---|---|
|
*1: Models with entry and start system *2: Models without entry and start system |
|
| Alarm | When the theft deterrent system switches to the alarm state, the warning items are operated and the alarm sounds for approximately 27.5 seconds. |
| Alarm Indicator | When the theft deterrent system switches to the armed preparation state or alarm state, the security indicator light is illuminated to inform the user. This indicator is also the immobiliser indicator, which blinks when the immobiliser is in the set state. |
| Forced Door Lock | The main body ECU (multiplex network body ECU) transmits a door lock signal to all the doors when all the following conditions are met:
·
The theft deterrent system is in the alarm state. ·
There is no electrical key transmitter sub-assembly in the actuation area.*1 ·
There is no key inserted in the ignition key cylinder.*2 ·
One of the doors has been unlocked. The function stops when one of the following conditions is met: ·
All doors are locked. ·
The warning ends after approximately 27.5 seconds. ·
The electrical key transmitter sub-assembly is in the actuation area.*1 ·
The ignition key is inserted in the ignition key cylinder.*2 |