Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
NM32H0E _51 Engine / Hybrid System _060218 3ZR-FAE ENGINE CONTROL _0295413 SFI SYSTEM DE DETAILS F

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  DETAILS  CRANKSHAFT POSITION SENSOR AND CAMSHAFT POSITION SENSOR  


CONSTRUCTION


a.

Magneto Resistive Element (MRE) type sensors are used for the crank position sensor, cam position sensor (intake) and cam position sensor (exhaust).


b.

The timing rotor of the crankshaft has 34 teeth, with 2 teeth missing. Based on these teeth, the crank position sensor transmits crank position signals (NE signal) consisting of 33 high or low output pulses every 10° per revolution of the crankshaft. The ECM uses the NE signal for detecting the crank position as well as for detecting the engine speed. It uses the missing teeth signal for determining the top dead center.


c.

To detect the cam position, each timing rotor on the intake and exhaust camshafts is used to generate 6 (3 high output, 3 low output) pulses for every 2 revolutions of the crankshaft.

W116610C01
3.604,0.25 3.76,0.25 3.76,0.25 4.219,0.583 true 4.854,0.313 4.698,0.313 4.698,0.313 4.458,0.729 true 2.042,4.281 2.198,4.281 2.198,4.281 2.531,2.938 true 1.833,4.188 2.146,4.344 0.313,0.156 10 false *1 3.385,0.156 3.698,0.313 0.313,0.156 10 false *2 4.896,0.208 5.208,0.365 0.313,0.156 10 false *3
*1 Crank Position Sensor *2 Cam Position Sensor (Exhaust)
*3 Cam Position Sensor (Intake) - -


Sensor Output Waveforms
W127829E03
0.188,1.104 1.615,1.385 1.427,0.281 10 false Crank Position Sensor 0.167,2.26 1.5,2.719 1.333,0.458 10 false Cam Position Sensor (Intake) 0.156,3.177 1.5,3.604 1.344,0.427 10 false Cam Position Sensor (Exhaust) 2.635,0.448 3.25,0.667 0.615,0.219 10 false 360° CA 2.146,0.729 2.75,0.917 0.604,0.188 10 false 10° CA 3.24,0.74 3.729,0.917 0.49,0.177 10 false 30° CA 4.333,0.448 4.917,0.698 0.583,0.25 10 false 360° CA 2.635,1.833 3.229,2.042 0.594,0.208 10 false 180° CA 3.521,1.833 4.083,2.031 0.563,0.198 10 false 180° CA 4.354,1.833 4.99,2.042 0.635,0.208 10 false 180° CA 2.365,2.771 2.917,2.99 0.552,0.219 10 false 180° CA 3.208,2.771 3.75,2.99 0.542,0.219 10 false 180° CA 4.063,2.771 4.688,2.969 0.625,0.198 10 false 180° CA


d.

An MRE type sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to either high or low. The ECM detects the crank position and intake and exhaust cam positions based on this output voltage.


e.

The differences between an MRE type sensor and the pick-up coil type sensor used on a conventional model are as follows.

·

An MRE type sensor outputs a constant level of high/low digital signals regardless of the engine speed. Therefore, an MRE type sensor can detect the positions of the crankshaft and camshaft at an early stage of cranking.

·

A pick-up coil type sensor outputs analog signals with levels that change with engine speed.


W100950E09
4.271,2.635 4.552,3.281 4.552,3.281 4.698,3.281 true 4.833,1.833 5.24,0.979 5.24,0.979 5.385,0.979 true 1.667,0.417 2.5,0.667 0.833,0.25 10 MRE Type 4.75,0.417 5.917,0.667 1.167,0.25 10 Pick-up Coil Type 5.438,0.917 6.313,1.156 0.875,0.24 10 No Detection 4.74,3.219 5.615,3.458 0.875,0.24 10 No Detection 0.26,1.281 0.75,1.688 0.49,0.406 10 Engine Speed 0.26,2.406 0.781,2.844 0.521,0.438 10 Sensor Output 3.573,2.448 4.063,2.875 0.49,0.427 10 Sensor Output 6.5,2.688 7.01,3.083 0.51,0.396 10 Analog Output 2.865,2.573 3.344,3.01 0.479,0.438 10 Digital Output 3.573,1.281 4.083,1.698 0.51,0.417 10 Engine Speed