Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
NM32H0E _51 Engine / Hybrid System _060218 3ZR-FAE ENGINE CONTROL _0295413 SFI SYSTEM DE DETAILS F

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  DETAILS  CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER  


CONSTRUCTION


a.

The basic components of the continuously variable valve lift controller assembly are an EDU, a brushless motor and a differential roller converter.


b.

The internal gears of the continuously variable valve lift controller assembly are lubricated by engine oil.


c.

A neodymium magnet* is used in a flat brushless motor to achieve a compact construction. The flat brushless motor is a DC motor from which the brushes and the commutator have been eliminated. A multipolar magnetized magnet acts as a rotor, which switches the polarity of the voltage applied to the surrounding stator actuation coil in sync with the rotation of the rotor. The resulting alternating field and the rotor magnet magnetic flux cause attraction and repulsion to generate torque.

HINT:

*: A neodymium magnet is a type of rare earth magnet composed primarily of neodymium, iron and boron. The neodymium magnet has a high magnetic flux density to provide extremely strong magnetism.



d.

The EDU operates the motor in accordance with signals from the ECM. The differential roller converter converts the rotational movement of the motor into a linear movement. This linear movement operates the VALVEMATIC mechanism.

W133591C01
2.24,4.323 2.406,4.323 2.406,4.323 3.302,5.063 true 3.719,0.969 4.031,0.5 4.031,0.5 4.198,0.5 true 3.406,5.115 3.833,4.302 3.833,4.302 4,4.302 true 3.417,5.396 4.021,4.604 4.021,4.604 4.188,4.604 true 3.99,5.354 4.438,4.708 4.438,4.708 4.604,4.708 true 1.844,4.781 2.01,4.781 2.01,4.781 2.781,5.469 true 3.979,6.052 4.625,6.74 4.625,6.74 4.792,6.74 true 2.104,6.896 2.271,6.896 2.271,6.896 2.823,6.229 true 4.219,0.417 4.531,0.573 0.313,0.156 10 false *1 1.656,4.677 1.969,4.833 0.313,0.156 10 false *2 4.052,4.208 4.365,4.365 0.313,0.156 10 false *3 4.24,4.51 4.552,4.667 0.313,0.156 10 false *4 4.656,4.604 4.969,4.76 0.313,0.156 10 false *5 4.823,6.635 5.135,6.792 0.313,0.156 10 false *6 0.313,3.781 0.625,3.938 0.313,0.156 10 false *a 2.031,4.219 2.344,4.375 0.313,0.156 10 false *b 1.906,6.813 2.219,6.969 0.313,0.156 10 false *c
*1 Continuously Variable Valve Lift Controller Assembly *2 EDU
*3 Stator *4 Rotor/Motor
*5 Bearing *6 Differential Roller Converter
*a Continuously Variable Valve Lift Controller Assembly Cross Section *b Motor Portion
*c Sensor Portion
·

Motor Position Sensor

·

Action Angle Sensor


- -
V100135

Engine Oil Out
V100136

Engine Oil In
V100137

Linear Movement
V100138

Rotational Movement



e.

The motor rotates the nut on the differential roller converter. The movement of the nut travels to the pinion and the planetary gear and causes the sun shaft to move linearly.

Differential Roller Converter
W133592C01
2.573,1.094 2.74,1.094 2.74,1.094 3.094,2.146 true 4.865,0.74 5.156,0.5 5.156,0.5 5.323,0.5 true 3.688,1.885 3.938,0.427 3.938,0.427 4.104,0.427 true 3.802,2.188 4.365,2.823 4.365,2.823 4.531,2.823 true 2.302,1.531 2.469,1.531 2.469,1.531 2.771,2.698 true 2.594,3.865 2.76,3.865 2.76,3.865 2.906,3.01 true 1.656,3.427 1.823,3.427 1.823,3.427 2.083,2.75 true 1.542,2.01 1.708,2.01 1.708,2.01 2.479,2.729 true 5.25,4.531 5.417,4.531 5.417,4.531 5.792,4.99 true 3,4.948 3.125,4.5 3.125,4.5 3.292,4.5 true 1.375,4.552 1.542,4.552 1.542,4.552 1.875,5.125 true 3.75,5.74 3.927,5.146 3.927,5.146 4.094,5.146 true 4.26,6.01 4.625,6.521 4.625,6.521 4.792,6.521 true 1.99,7.01 2.156,7.01 2.156,7.01 2.417,6.396 true 0.708,5.302 0.875,5.302 0.875,5.302 1.188,5.802 true 1.354,1.917 1.667,2.073 0.313,0.156 10 false *1 4.156,0.333 4.469,0.49 0.313,0.156 10 false *2 2.365,1 2.677,1.156 0.313,0.156 10 false *3 5.365,0.417 5.677,0.573 0.313,0.156 10 false *4 4.594,2.729 4.906,2.885 0.313,0.156 10 false *5 1.458,3.333 1.771,3.49 0.313,0.156 10 false *6 2.104,1.438 2.417,1.594 0.313,0.156 10 false *2 2.406,3.771 2.719,3.927 0.313,0.156 10 false *5 5.052,4.438 5.365,4.594 0.313,0.156 10 false *5 3.344,4.396 3.656,4.552 0.313,0.156 10 false *3 1.188,4.458 1.5,4.615 0.313,0.156 10 false *1 4.167,5.063 4.479,5.219 0.313,0.156 10 false *2 4.844,6.427 5.156,6.583 0.313,0.156 10 false *4 1.802,6.917 2.115,7.073 0.313,0.156 10 false *2 0.531,5.208 0.844,5.365 0.313,0.156 10 false *5
*1 Pinion *2 Sun Gear
*3 Planetary Gear *4 Sun Shaft
*5 Ring Gear *6 Nut
V100135

Rotational Movement
V100136

Linear Movement




OPERATION


a.

On the basic control, the ECM determines the target intake air volume in accordance with the accelerator pedal depressed angle, engine speed and various sensor signals. The EDU, which is integrated into the continuously variable valve lift controller assembly, determines the target amount of lift and the action angle of the intake valve in accordance with signals from the ECM.

Basic Control Flow Chart
W123602E01
0.104,0.063 3.771,0.26 3.667,0.198 10 false Basic Control Flow Chart 2.01,0.635 2.531,1.146 0.521,0.51 10 false Upon Starting 2.802,0.635 3.302,1.146 0.5,0.51 10 false At First Idling 3.688,0.635 4.281,1.167 0.594,0.531 10 false Before Warm-up 4.917,0.635 5.875,0.979 0.958,0.344 10 false After Warm-up 6.385,0.635 6.958,1.302 0.573,0.667 10 false Stopping Engine 4.656,1.031 5.156,1.688 0.5,0.656 10 false At Light Load 5.365,1.031 6.396,1.438 1.031,0.406 10 false At Heavy Load 0.531,2.125 1.563,2.531 1.031,0.406 10 false Starter Signal 0.531,2.656 1.563,3.063 1.031,0.406 10 false Engine Speed 0.073,3.24 0.896,4.01 0.823,0.771 10 false Intake Valve Action Angle (CA) 1.104,3.188 2.135,3.594 1.031,0.406 9 false 280 1.104,3.313 2.135,3.719 1.031,0.406 9 false 240 1.104,3.438 2.135,3.844 1.031,0.406 9 false 200 1.104,3.656 2.135,4.063 1.031,0.406 9 false 106 3,3.677 4.031,4.083 1.031,0.406 9 false 150 5.646,3.083 5.948,3.365 0.302,0.281 9 false 280 5.792,6.25 6.427,6.563 0.635,0.313 10 false Time 0.073,4.417 1.083,5.198 1.01,0.781 10 false Advanced Angle of Intake Valve (CA) 1.188,4.385 2.219,4.792 1.031,0.406 9 false 62 1.188,4.615 2.219,5.021 1.031,0.406 9 false 20 1.26,4.854 2.292,5.26 1.031,0.406 9 false 0 0.073,5.635 1.125,6.396 1.052,0.76 10 false Advanced Angle of Exhaust Valve (CA) 1.188,5.583 2.219,5.99 1.031,0.406 9 false 50 1.188,5.813 2.219,6.219 1.031,0.406 9 false 20 1.26,6.073 2.292,6.479 1.031,0.406 9 false 0


b.

To optimize the valve opening and closing timing, the VALVEMATIC effects coordinate control with the dual VVT-i. Thus, the VALVEMATIC controls the amount of valve lift and the action angle in accordance with the driving conditions. Because the VALVEMATIC features timing advance characteristics in which the amount of valve lift and the action angle vary, it effects the proper control to attain the intended amount of valve lift. This VVT-i has timing advance characteristics that differ from the conventional dual VVT-i control.

VALVEMATIC Operating Range
W100449E10
3.927,1.292 4.427,0.781 4.427,0.781 4.688,0.781 true 4.25,1.823 4.49,2.073 4.49,2.073 4.667,2.073 true 1.917,0.99 2.656,1.646 0.74,0.656 10 false Amount of Valve Lift 3,0.26 3.615,0.927 0.615,0.667 10 false Exhaust Valve 3.698,0.26 4.188,0.885 0.49,0.625 10 false Intake Valve 4.76,0.708 6.948,1.198 2.188,0.49 10 false Amount of Intake Valve Lift (1.1 mm (0.0433 in.) to 11.5 mm (0.453 in.)) 3.052,1.885 4.24,2.292 1.188,0.406 10 false Valve Action Angle 4.729,1.99 6.344,2.552 1.615,0.563 10 false Intake Valve Action Angle (106° CA to 280° CA)

Valve Opening and Closing Graph
W100450E08
3,0.302 3.615,0.927 0.615,0.625 10 false Exhaust Valve 3.781,0.313 4.271,0.938 0.49,0.625 10 false Intake Valve 1.958,1.01 2.667,1.667 0.708,0.656 10 false Amount of Valve Lift 0.74,1.885 6.135,2.604 5.396,0.719 10 false The exhaust valve opening timing is adjusted in accordance with the timing intake valve opening timing. Thus, by closing the intake valve early, fuel economy is improved.

Relationship between Intake Valve Action Angle and VVT-i
W113592E02
2.667,0.583 2.917,0.583 2.917,0.583 3.583,1.167 true 5.083,0.573 4.833,0.573 4.833,0.573 4.417,1.135 true 2,3.333 2.25,3.333 2.25,3.333 2.667,2.865 true 5.083,1.917 4.833,1.917 4.833,1.917 4.417,2.135 true 5.083,3.042 4.833,3.042 4.833,3.042 3.833,2.042 true 1.729,0.479 2.74,0.75 1.01,0.271 10 false After Warm-up 5.156,0.469 6.417,0.802 1.26,0.333 10 false Before Warm-up 1,1.625 2.219,2.125 1.219,0.5 10 false Intake Valve Action Angle (°CA) 3.031,3.167 4.208,3.594 1.177,0.427 10 false Advanced Angle of Intake Valve (°CA) 1.417,3.229 2.083,3.479 0.667,0.25 10 false At Idling 5.156,1.813 6.5,2.229 1.344,0.417 10 false Upon Engine Starting and Stopping 5.167,2.927 6.51,3.344 1.344,0.417 10 false Engine Stopped


c.

The following table shows the coordinated control of the VALVEMATIC with ETCS-i during basic control:

Control Operation
Starting Control VALVEMATIC controls the intake valve action angle, and ETCS-i operates the throttle valve to control the intake air volume.
Fast Idle Control
Before Warm-up Control
After Warm-up Control
·

VALVEMATIC controls the amount of intake valve lift and the intake valve timing, and ETCS-i opens the throttle valve wider than the normal opening and reduces the intake manifold negative pressure in order to minimize pumping loss.

·

During idling, when the intake air volume is small, the ETCS-i controls the intake air volume as in the past.


Engine Stop Control