Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
NM32H0E _51 Engine / Hybrid System _060218 3ZR-FAE ENGINE CONTROL _0295413 SFI SYSTEM CO CONTROL F

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  CONTROL  ELECTRICAL SPARK ADVANCE (ESA) CONTROL  


FUNCTION


a.

The optimum ignition timing is selected according to signals from the sensors and the ignition signal (IGt) is sent to the igniter.

W133583E01
0.219,0.26 3.542,0.552 3.323,0.292 10 false Intake Mass Air Flow Meter Sub-assembly 0.25,0.615 3.573,0.906 3.323,0.292 10 false Intake Air Temperature Sensor 0.198,1.104 3.521,1.396 3.323,0.292 10 false Crank Position Sensor 0.188,1.583 3.51,1.875 3.323,0.292 10 false Cam Position Sensor (Intake) 0.188,2.073 3.51,2.365 3.323,0.292 10 false Cam Position Sensor (Exhaust) 0.208,2.563 3.531,2.854 3.323,0.292 10 false Air Fuel Ratio Sensor 0.198,3.01 3.521,3.302 3.323,0.292 10 false Oxygen Sensor 0.198,3.49 3.521,3.781 3.323,0.292 10 false Accelerator Pedal Sensor Assembly 0.208,3.958 3.531,4.25 3.323,0.292 10 false Throttle Position Sensor 0.219,4.438 3.542,4.729 3.323,0.292 10 false E.F.I. Engine Coolant Temperature Sensor 0.198,4.938 3.521,5.229 3.323,0.292 10 false Knock Control Sensor 0.198,5.396 3.521,5.688 3.323,0.292 10 false Park/Neutral Position Switch Assembly 0.188,5.896 3.51,6.188 3.323,0.292 10 false Starter Relay Assembly 0.208,6.354 3.531,6.646 3.323,0.292 10 false Combination Meter Assembly 4.677,3.344 5.458,4.167 0.781,0.823 10 false ECM 6.052,2.938 6.802,3.51 0.75,0.573 10 false Ignition Coil Assembly


b.

The ignition timing can be expressed using the following equation. The ignition timing is set initially to 10° BTDC.

Ignition Timing = A. Initial Set Ignition Timing or B. Basic Advanced Angle + C. Corrected Advanced Angle
A. Fixed Advanced Angle Characteristics Fixed to 5° BTDC when starting the engine. The service terminals are short-circuited, and it is fixed to 10° BTDC when the throttle is closed.
B. Basic Advanced Angle Characteristics Selects the optimum ignition timing, depending on each sensor signal.
C. Correction Advanced Angle Characteristics Selects the appropriate advanced or retarded angles according to the engine status at that time, depending on each sensor signal.
C-1. Warm-up Advanced Angle Characteristics Sets the ignition timing to advanced angle according to the operating status to improve drivability, when the coolant temperature is low.
C-2. Idling Stability Advanced Angle Characteristics Sets the ignition timing to advance to stabilize idle speed when the idle speed is low. Also, as the speed gets higher, the ignition timing is retarded.
C-3. Knocking Correction Retarded Angle When knocking is generated, the ignition timing is corrected according to a signal from the knock control sensor.


c.

If engine knocking is detected, the ignition timing is retarded gradually in equal steps according to the size of knocking, until the engine stops knocking.


d.

After knocking has stopped, the ignition timing is advanced gradually in equal steps. If the engine knocks again during this process, then the ignition timing is retarded again.

Knocking Feedback Control Cycle
W116212E02
1.333,0.25 3.625,0.448 2.292,0.198 10 false Knocking Occurs 5.083,0.25 6,0.448 0.917,0.198 10 false Retard 1.667,1.219 2.74,1.417 1.073,0.198 10 false Advance 4.896,1.219 6.583,1.417 1.688,0.198 10 false No Knocking