Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
NM32H0E _51 Engine / Hybrid System _060218 3ZR-FAE ENGINE CONTROL _0295413 SFI SYSTEM CO CONTROL F

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  CONTROL  DRIVE START CONTROL SYSTEM  


FUNCTION


a.

When abnormal driver accelerator pedal and shift operations are detected, the system limits the engine output and informs the driver.

W134794E02
0.188,0.25 2.625,0.5 2.438,0.25 10 false Accelerator Pedal Sensor Assembly 0.198,0.813 2.635,1.063 2.438,0.25 10 false Park/Neutral Position Switch Assembly 0.188,1.344 2.625,1.594 2.438,0.25 10 false Transmission Revolution Sensor (NT) 0.208,1.896 2.646,2.146 2.438,0.25 10 false Transmission Revolution Sensor (NIN) 0.219,2.667 2.656,2.917 2.438,0.25 10 false Airbag Sensor Assembly 0.219,3.771 2.656,4.021 2.438,0.25 10 false Skid Control ECU 0.542,4.406 2.979,4.656 2.438,0.25 10 false : CAN Communication Line 4.615,1.115 5.438,1.635 0.823,0.521 10 false ECM 6.083,0.594 7.021,1.063 0.938,0.469 10 false Engine Output 6.063,1.25 6.854,1.771 0.792,0.521 10 false Combination Meter Assembly 4.417,2.667 4.969,3.198 0.552,0.531 10 false Network Gateway ECU

HINT:

When the system is operating, even if the driver depresses and holds the accelerator pedal, engine output may increase on an uphill slope and decrease on a downhill slope. This behavior allows the system to restrict the vehicle speed and acceleration below the predetermined limit on slopes and is not a malfunction.



b.

Shift Change Control

i.

Responds to shift operations with the accelerator pedal depressed.


ii.

Changes the limit amount according to the shift operation pattern.


iii.

Corrects engine output according to the road grade.

Control Start Conditions (When the conditions of either pattern A or pattern B are met, control starts.) Pattern A (When all of the following conditions are met, control starts.)
·

Accelerator opening angle is approximately 1/5 or higher.

·

Shift state is changed from P to D/M, or P to R.


Pattern B (When all of the following conditions are met, control starts.)
·

Accelerator opening angle is approximately 1/5 or higher.

·

Shift state is changed from R to D/M, D/M to R, or N to R.


Control Operation Restricts the engine output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions (Control stops when any of the conditions are met.)
·

Accelerator pedal is fully released.

·

Shift state is P or N.



W135015E01
2.458,1.719 2.667,1.417 2.667,1.417 3.5,1.417 true 3.083,0.99 3.271,0.656 3.271,0.656 3.438,0.656 true 4.542,3.969 4.729,3.635 4.729,3.635 4.896,3.635 true 4.479,3.031 4.667,2.698 4.667,2.698 4.833,2.698 true 4.479,3.042 4.667,2.708 4.667,2.708 4.833,2.708 true 3.51,0.573 6.083,0.896 2.573,0.323 10 false Shift operation of pattern A or pattern B 3.563,1.323 7.01,1.531 3.448,0.208 10 false Accelerator pedal is open by approximately 1/5 or more. 2.781,2.5 4.396,2.781 1.615,0.281 10 false Activated 4.927,2.635 6.542,2.917 1.615,0.281 10 false without Control 4.24,3.313 5.854,3.594 1.615,0.281 10 false Restricted 4.969,3.521 6.583,3.802 1.615,0.281 10 false with Control* 3.344,4.094 4.958,4.375 1.615,0.281 10 false Time 0.521,4.396 5.74,4.646 5.219,0.25 10 false *: The engine output restraint level differs between pattern A and pattern B. 1.344,3.219 2.958,3.5 1.615,0.281 10 false Engine Output 0.875,1.938 2.49,2.219 1.615,0.281 10 false Accelerator Pedal Off 0.885,1.625 2.5,1.906 1.615,0.281 10 false Accelerator Pedal On 1.01,1.198 2.625,1.479 1.615,0.281 10 false Shift Lever Position

HINT:
·

The engine output restraint level differs between pattern A and pattern B.

·

During control while a shift operation is performed (from control start until the accelerator pedal is released), the system informs the driver of the control via the combination meter assembly.





c.

Control during Reverse Operation

i.

Responds to excessive depression of the accelerator pedal while operating in reverse.


ii.

Corrects engine output according to the road grade.

Control Start Conditions (When all of the following conditions are met, control starts.)
·

Shift state is R.

·

Accelerator pedal is depressed excessively.


Control Operation Restricts the engine output so the vehicle speed and acceleration are at or below a certain level.
Control Stop Conditions (Control stops when any of the conditions are met.)
·

Accelerator pedal is fully released.

·

Shift state is not R.



W135016E01
3.167,1.344 3.5,1.042 3.5,1.042 3.667,1.042 true 4.542,2.906 4.875,2.604 4.875,2.604 5.042,2.604 true 4.667,3.552 4.865,3.729 4.865,3.729 5.031,3.729 true 2.76,0.802 2.917,1 0.156,0.198 10 false R 3.76,0.948 6.958,1.198 3.198,0.25 10 false When the accelerator pedal is suddenly depressed. 5.115,2.51 6.208,2.76 1.094,0.25 10 false without Control 4.469,3.052 5.563,3.302 1.094,0.25 10 false Restricted 5.125,3.625 6.219,3.875 1.094,0.25 10 false with Control 3.427,4 4.521,4.25 1.094,0.25 10 false Time 1.479,3.156 2.573,3.406 1.094,0.25 10 false Engine Output 2.885,2.385 3.979,2.635 1.094,0.25 10 false Activated 1.01,1.25 3.021,1.521 2.01,0.271 10 false Accelerator Pedal On 1.01,1.646 2.927,1.906 1.917,0.26 10 false Accelerator Pedal Off 1.135,0.781 2.781,1.01 1.646,0.229 10 false Shift Lever Position