Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE UNIT
NM32H0E _51 Engine / Hybrid System _060231 3ZR-FAE ENGINE MECHANICAL _0295458 ENGINE UNIT DE DETAILS F

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CRANKSHAFT AND BEARING  


CONSTRUCTION


a.

The crankshaft has 5 journals and 8 balance weights.


b.

The pins and journals have been machined with increased precision and the surface roughness has been minimized to reduce friction.


c.

All pins and journal fillets have been hardened to improve their strength.

W116604C01
1.76,2.542 1.896,2.542 1.896,2.542 2.198,1.969 true 1.531,2.146 1.667,2.146 1.667,2.146 1.969,1.573 true 4.281,2.604 4.146,2.604 4.146,2.604 3.875,2.031 true 5.448,0.75 5.313,0.75 5.313,0.75 5.146,1.198 true 5.052,0.292 4.917,0.292 4.917,0.292 4.75,0.74 true 2.479,0.323 2.625,0.323 2.625,0.323 2.865,1.167 true 1.313,2.042 1.625,2.198 0.313,0.156 10 false *1 1.542,2.438 1.854,2.594 0.313,0.156 10 false *2 5.49,0.646 5.802,0.802 0.313,0.156 10 false *3 2.26,0.219 2.573,0.375 0.313,0.156 10 false *a 5.083,0.188 5.396,0.344 0.313,0.156 10 false *b 4.323,2.5 4.635,2.656 0.313,0.156 10 false *c
*1 No. 1 Journal *2 Balance Weight
*3 No. 5 Journal - -
*a Journal Fillet *b Oil Hole
*c Pin Fillet - -



d.

The width of the crankshaft bearings has been optimized to reduce friction.


e.

An oil groove is provided on each crankshaft bearing (upper main bearing). The oil groove is deep at the center and is shallow at the edges to reduce the amount of oil that leaks from the crankshaft bearing. As a result, the size of the oil pump has been reduced, minimizing friction.


f.

The lining surface of the crankshaft bearings are micro-grooved to provide an optimal amount of oil clearance. As a result, cold-engine cranking performance has been improved and engine vibration has been reduced.

W133610C01
2.198,0.677 2.365,0.677 2.365,0.677 2.656,1.521 true 2.927,0.469 3.094,0.469 3.094,0.469 3.365,1.146 true 2.292,3.24 2.458,3.24 2.458,3.24 2.781,2.76 true 2.75,0.365 3.063,0.521 0.313,0.156 10 false *1 2.094,3.146 2.406,3.302 0.313,0.156 10 false *2 0.521,0.948 0.833,1.104 0.313,0.156 10 false *a 2.01,0.573 2.323,0.729 0.313,0.156 10 false *b 4.979,1.875 5.292,2.031 0.313,0.156 10 false *c 5.469,1.552 5.781,1.708 0.313,0.156 10 false *d 4.229,0.76 4.542,0.917 0.313,0.156 10 false *e 6,1.885 6.313,2.042 0.313,0.156 10 false *c
*1 Upper Main Bearing *2 Lower Main Bearing
*a Micro-grooved *b Oil Groove
*c Edge *d Center
*e Oil Groove Depth - -