Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE UNIT
NM32H0E _51 Engine / Hybrid System _060231 3ZR-FAE ENGINE MECHANICAL _0295458 ENGINE UNIT GE GENERAL F

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 3ZR-FAE engine is an in-line 4-cylinder, 2.0-liter, 16-valve DOHC engine. This engine uses the VALVEMATIC system, dual Variable Valve Timing-intelligent (VVT-i) system, Direct Ignition System (DIS) and Electronic Throttle Control System-intelligent (ETCS-i). These systems have been developed to achieve high performance, fuel economy, and reduced exhaust emissions.



SPECIFICATION


Item Specification
Engine Type 3ZR-FAE
No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive (with VALVEMATIC and Dual VVT-i)
Combustion Chamber Pentroof Type
Flow of intake and Exhaust Gasses Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI)
Ignition System Direct Ignition System (DIS)
Displacement 1987 cm3 (121.3 cu. in.)
Bore x Stroke 80.5 mm x 97.6 mm (3.17 in. x 3.84 in.)
Compression Ratio 10.5 : 1
Max. Output (EEC) 109 kW @ 6000 to 6100 rpm
Max. Torque (EEC) 189 N*m @ 3800 to 3900 rpm
Valve Timing Intake Open -14° to 25° BTDC
Closed 80° to -66° ABDC
Exhaust Open 65° to 20° BBDC
Closed -1° to 44° ATDC
Spark Plug Manufacture DENSO
Type SC16HR11 or SC20HR11
Plug Gap 1.0 mm to 1.1 mm (0.0394 in. to 0.0433 in.)
Firing Order 1 - 3 - 4 - 2
Research Octane Number (RON) 91 or higher
Emission Regulation EURO 5+
Engine Service Mass (Reference)* 147 kg (324.0 lb.)

HINT:

*: Weight shows the figure with oil and engine coolant fully filled.



MAIN FEATURES


a.

The 3ZR-FAE engine has achieved the following through the adoption of the items listed in the table.

(A): High performance and reliability

(B): Low noise and vibration

(C): Lightweight and compact design

(D): Good serviceability

(E): Clean emissions and fuel economy

Item (A) (B) (C) (D) (E)
A cylinder block made of aluminum alloy is used. - - ○ - -
Spiny liners are used. ○ - - - -
The skirt portion of the piston has a resin coating applied to reduce friction. ○ ○ - - ○
Low tension piston rings are used. ○ - - - ○
A timing chain and a chain tensioner are used. - ○ - ○ -
Valve lash adjuster assemblies are used. - ○ - ○ -
No. 1 valve rocker arm sub-assemblies are used. ○ ○ - ○ -
The VALVEMATIC system is used. ○ - - - ○
The dual Variable Valve Timing-intelligent (VVT-i) system is used. ○ - - - ○
A variable discharge oil pump assembly is used. ○ - - - -
An oil filter with a replaceable element is used. - - - ○ -
Toyota Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
An intake manifold made of plastic is used. - - ○ - -
A stainless steel exhaust manifold is used. - - ○ - ○
Three-Way Catalysts (TWCs) are used. - - - - ○
A fuel returnless system is used. - - ○ ○ ○
Quick connectors are used to connect the fuel hoses with the fuel pipes. - - - ○ -
A serpentine belt drive system is used. ○ - ○ ○ -
A Magneto Resistive Element (MRE) type crank position sensor and cam position sensor are used. - - - - ○
The Direct Ignition System (DIS) makes ignition timing adjustment unnecessary. ○ - - ○ ○
The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - -

HINT:

○: Applicable

-: Not applicable