Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2018.05
NM32H0E _51 Engine / Hybrid System _060396 8NR-FTS ENGINE CONTROL _0296167 SFI SYSTEM CO CONTROL F

8NR-FTS ENGINE CONTROL  SFI SYSTEM  CONTROL  DIRECT INJECTION 4-STROKE GASOLINE ENGINE SEQUENTIAL MULTIPORT FUEL INJECTION (D-4 SFI)  


FUNCTION


a.

A Direct injection 4-stroke gasoline engine Sequential multiport Fuel Injection (D-4 SFI) system which has both direct injection type and port injection type is used for the fuel injection system.


b.

The intake air mass is detected by the intake mass air flow meter sub-assembly to control the fuel injection volume.


c.

Based on signals from each sensor, the ECM controls the injection volume and timing of fuel injector assembly in accordance with the engine speed and engine load in order to optimize combustion conditions. Due to this, engine oil dilution reduction, low fuel consumption, and improved emission as well as high engine output are achieved.


d.

In order to fully maximize the effectiveness of the direct injection (cooling effect, jet stream use, air-fuel mixture form variance), multi-fuel injection system in which injection is divided over multiple times is used.


e.

On the models with stop and start system, during engine start while the idling stop control is operating, direct injection is used. Fuel is directly injected into the cylinder stopped by the compression stage. This allows the engine to start quickly and smoothly.

W134782E01
0.229,0.24 2.979,0.49 2.75,0.25 10 false Intake Mass Air Flow Meter Sub-assembly 0.281,0.604 3.031,0.854 2.75,0.25 10 false Intake Air Temperature Sensor 0.208,1.115 2.958,1.365 2.75,0.25 10 false Crank Position Sensor 0.208,1.604 3.302,2 3.094,0.396 10 false Intake Cam Position Sensor (No. 1 Crank Position Sensor) 0.208,2.448 3.417,2.875 3.208,0.427 10 false Exhaust Cam Position Sensor (No. 2 Crank Position Sensor) 0.208,3.26 2.958,3.51 2.75,0.25 10 false Air Fuel Ratio Sensor 0.208,3.729 2.958,3.979 2.75,0.25 10 false Oxygen Sensor 0.208,4.208 2.958,4.458 2.75,0.25 10 false Accelerator Pedal Sensor Assembly 0.208,4.698 1.75,4.927 1.542,0.229 10 false Throttle Position Sensor 0.198,5.167 2.563,5.406 2.365,0.24 10 false Engine Coolant Temperature Sensor 0.219,5.646 2.583,5.885 2.365,0.24 10 false No. 1 Turbo Pressure Sensor 0.271,6 2.635,6.24 2.365,0.24 10 false Intake Air Temperature Sensor 0.208,6.521 2.573,6.76 2.365,0.24 10 false No. 2 Turbo Pressure Sensor 0.208,7 1.698,7.24 1.49,0.24 10 false Fuel Pressure Sensor 0.229,7.469 2.594,7.708 2.365,0.24 10 false Combination Meter Assembly 4.677,3.813 5.135,4.01 0.458,0.198 10 false ECM 6.073,3.5 6.896,4.198 0.823,0.698 10 false Fuel Injector Assembly


f.

Fuel injection is stopped to protect the engine and improve fuel efficiency.

Fuel Cut Speed at High Engine Speed
Engine Speed (rpm) 5800 or more