Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2018.05–2019.09
NM32H0E _56 Audio / Visual / Telematics _060816 PARK ASSIST / MONITORING _0298320 BLIND SPOT MONITOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  CONTROL  BLIND SPOT MONITOR CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Blind Spot Monitor Sensor LH and RH
·

Outputs millimeter waves from the blind spot monitor sensor to the blind spot sensor detection area, uses the reflected millimeter waves for detecting the presence of a vehicle, the vehicle-to-vehicle distance, and the relative speed, and then sends this information to the built-in signal processing circuit.

·

The signal processing circuit determines if a vehicle is present, and illuminates or blinks the outer rear view mirror indicator accordingly.

·

Dims the outer rear view mirror indicator light on the outer rear view mirror assembly.


Outer Rear View Mirror Assembly LH and RH Outer Rear View Mirror Indicator Light
·

Illuminates to inform the driver that a vehicle has been detected in the blind spot monitor sensor detection area.

·

Flashes to inform the driver when the turn signal lever is operated if a vehicle has been detected in the blind spot monitor sensor detection area.

·

Both indicator lights flash to inform the driver that a vehicle has been detected in the blind spot detection area while the driver is reversing.


Combination Meter Assembly Multi-information Display When a malfunction is detected in the blind spot monitor sensors or the blind spot monitor sensors determine that control is not possible, a message is displayed on the multi-information display to warn the driver.
BSM Indicator Light Illuminates to inform the driver when the blind spot monitor system is on.
RCTA Indicator Light Illuminates to inform the driver when the RCTA function is on.
Combination Meter Assembly Sends the turn light signal to the blind spot monitor sensor LH and RH.
Steering Pad Switch Assembly Sends operation signals from switches to the spiral cable with sensor sub-assembly.
Spiral Cable with Sensor Sub-assembly Sends operation signals from the steering pad switch assembly to the combination meter assembly.
Steering Sensor Sends the steering angle signal to the blind spot monitor sensor LH and RH.
Airbag Sensor Assembly Sends yawrate information to the blind spot monitor sensor LH and RH.
Yawrate Sensor Assembly
ECM Sends the reverse signal to the blind spot monitor sensor LH and RH.
Brake Actuator Assembly
·

Skid Control ECU


Sends the vehicle speed signal to the blind spot monitor sensor LH and RH.
Main Body ECU (Multiplex Network Body ECU) Sends the destination signal, illumination signal and dimmer signal to the blind spot monitor sensor LH and RH.
RCTA Buzzer (Blind Spot Monitor Buzzer) Sounds when a vehicle is detected in the blind spot monitor sensor detection area while the driver is reversing.


SYSTEM CONTROL


a.

The blind spot monitor function operates when all of the following conditions are met:

i.

The blind spot monitor function is on.


ii.

The shift lever is in a position other than R.


iii.

The vehicle speed is greater than approximately 16 km/h (10 mph).



b.

The blind spot monitor function can detect vehicles in its detection areas.

i.

The detection areas formed by the blind spot monitor sensor LH and RH are as shown below.

Y170737C01
1.313,3.177 1.625,3.333 0.313,0.156 10 false *a 2.875,0.427 3.188,0.583 0.313,0.156 10 false *b 3.927,0.792 4.24,0.948 0.313,0.156 10 false *c 4.542,0.792 4.854,0.948 0.313,0.156 10 false *d 1.323,1.458 1.635,1.615 0.313,0.156 10 false *a 3.01,4.167 3.323,4.323 0.313,0.156 10 false *b 3.917,3.865 4.229,4.021 0.313,0.156 10 false *c 4.521,3.865 4.833,4.021 0.313,0.156 10 false *d
*a Approximately 3.5 m (11.5 ft) *b Approximately 60 m (197 ft)
*c Approximately 3.0 m (9.8 ft) *d Approximately 1.0 m (3.3 ft)
V100144

Detection Area (for Vehicle in Blind Spot)
V100145

Detection Area (for Rapidly Approaching Vehicle from Behind)



ii.

Detection Area

·

When this vehicle is overtaken by another vehicle in an adjacent lane.

Y110645C03
4.25,2.229 4.25,1.698 true 4.188,2.24 4.5,2.438 0.313,0.198 10 false *a
*a This Vehicle - -
V100135

Vehicle Speed (Fast)
V100136

Vehicle Speed (Slow)
V100144

Detection Area - -


·

When another vehicle enters the detection area of this vehicle due to a lane change.

Y110646C07
2.094,1.948 2.094,2.25 true 5.604,1.896 5.604,2.198 true 1.656,2.354 1.885,2.542 0.229,0.188 10 false *a 2,2.26 2.229,2.448 0.229,0.188 10 false *c 5.542,2.25 5.771,2.438 0.229,0.188 10 false *c 5,2.354 5.229,2.542 0.229,0.188 10 false *b
*a Other vehicle enters the detection area during lane change (merge in) (Type 1). *b Other vehicle enters the detection area during lane change (merge in) (Type 2).
*c This Vehicle - -
V100135

Motion direction of this vehicle
V100136

Motion direction of other vehicle
V100144

Detection Area - -




iii.

Detection Area

·

When another vehicle is rapidly approaching from behind.

Y170803C01
5.99,2.333 5.99,1.75 true 5.948,2.375 6.26,2.573 0.313,0.198 10 false *a
*a This Vehicle - -
V100135

Vehicle Speed (Fast)
V100136

Vehicle Speed (Slow)
V100145

Detection Area - -


·

When another vehicle enters the detection area of this vehicle due to a lane change and approaches this vehicle.

Y170805C01
5.594,1.917 5.594,2.458 true 5.625,3.938 5.625,4.479 true 3.427,2.302 3.74,2.5 0.313,0.198 10 false *a 3.448,4.302 3.76,4.5 0.313,0.198 10 false *b 5.531,2.479 5.844,2.677 0.313,0.198 10 false *c 5.563,4.51 5.875,4.708 0.313,0.198 10 false *c
*a Other vehicle enters the detection area during lane change (merge in) (Type 1). *b Other vehicle enters the detection area during lane change (merge in) (Type 2).
*c This Vehicle - -
V100135

Motion direction of this vehicle
V100136

Motion direction of other vehicle
V100145

Detection Area - -





c.

The RCTA function operates when all of the following conditions are met:

i.

The RCTA function is on.


ii.

The shift lever is in R.


iii.

The speed of this vehicle is less than approximately 8 km/h (5 mph).


iv.

Target vehicle's speed is between approximately 8 km/h (5 mph) and 28 km/h (18 mph).



d.

The RCTA function can detect vehicles in its detection areas.

i.

The system continuously measures the relative speed of an approaching vehicle and its distance. If it is determined that the approaching vehicle will cross the path of this vehicle, the Estimated Crossing Time (ECT) is calculated. When the ECT is 2.5 seconds or less, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the RCTA buzzer (blind spot monitor buzzer).

Y142884C01
4.021,0.688 4.188,0.229 4.188,0.229 4.333,0.229 true 3.281,1.531 3.208,0.927 3.208,0.927 3.073,0.927 true 1.708,1.542 1.635,0.938 1.635,0.938 1.5,0.938 true 4.354,0.135 4.667,0.292 0.313,0.156 10 false *a 2.875,0.823 3.188,0.979 0.313,0.156 10 false *b 1.292,0.833 1.604,0.99 0.313,0.156 10 false *c 3.615,2 3.927,2.156 0.313,0.156 10 false *d 2.917,2.313 3.229,2.469 0.313,0.156 10 false *e 3.198,2 3.51,2.156 0.313,0.156 10 false *f 1.792,2.313 2.104,2.469 0.313,0.156 10 false *f
*a This Vehicle *b Target Vehicle (Approximately 8 km/h (5 mph))
*c Target Vehicle (Approximately 28 km/h (18 mph)) *d Approximately 5.5 m (18.0 ft.)
*e Approximately 20 m (66 ft.) *f Target Detection Line
V100144

Alert Area - -



ii.

Normal Parking

Y129967C01
5.198,1.844 5.417,1.26 5.417,1.26 5.583,1.26 true 2.146,2.104 2.031,1.51 2.031,1.51 1.875,1.51 true 3.615,0.594 3.615,0.385 3.615,0.385 3.719,0.385 true 3.74,0.292 4.052,0.448 0.313,0.156 10 false *a 5.615,1.156 5.927,1.313 0.313,0.156 10 false *b 1.667,1.417 1.979,1.573 0.313,0.156 10 false *b
*a This Vehicle *b Target Vehicle
V100145

Alert Area - -




e.

According to operation conditions, the blind spot monitor function promotes safety confirmation by using the outer rear view mirror indicator light to inform the driver that system detects vehicles that are in or rapidly approaching the vehicle's blind spot.


f.

The outer rear view mirror indicator light illuminates when a vehicle is in or rapidly approaching the vehicle's blind spot and the turn light switch is not operated. The indicator light flashes when a vehicle is in or rapidly approaching the vehicle's blind spot and the turn light switch is operated.

Y207739E01
0.177,0.573 1.594,0.927 1.417,0.354 10 false Outer Rear View Mirror Assembly LH 0.344,1.385 1.75,1.76 1.406,0.375 10 false Outer Rear View Mirror Indicator Light 2.375,1.042 3.094,1.552 0.719,0.51 10 false Blind Spot Monitor Sensor LH 3.958,1.052 4.677,1.563 0.719,0.51 10 false Blind Spot Monitor Sensor RH 5.073,0.573 6.49,0.917 1.417,0.344 10 false Outer Rear View Mirror Assembly RH 5.24,1.396 6.646,1.771 1.406,0.375 10 false Outer Rear View Mirror Indicator Light 0.125,3.531 1.75,3.74 1.625,0.208 10 false Brake Actuator Assembly 0.229,3.927 1.854,4.135 1.625,0.208 10 false Skid Control ECU 0.156,4.552 1.781,4.76 1.625,0.208 10 false Airbag Sensor Assembly 0.229,4.948 1.292,5.146 1.063,0.198 10 false Yawrate Sensor 0.115,5.563 1.635,5.927 1.521,0.365 10 false Spiral Cable with Sensor Sub-assembly 0.219,6.156 1.26,6.354 1.042,0.198 10 false Steering Sensor 0.896,7.115 2.781,7.313 1.885,0.198 10 false : CAN Communication Line 4.885,4.917 5.26,5.104 0.375,0.188 10 false ECM 4.865,3.917 6.844,4.135 1.979,0.219 10 false Combination Meter Assembly 3.26,3.615 3.833,4.635 0.573,1.021 10 false Central Gateway ECU (Network Gateway ECU)


g.

According to operation conditions, the RCTA function promotes safety confirmation by using the outer rear view mirror indicator lights and RCTA buzzer (blind spot monitor buzzer) to inform the driver that another vehicle has entered the blind spot monitor sensor alert area of this vehicle.


h.

When this vehicle is reversing, if a vehicle enters the detection area of the blind spot monitor sensors and it is determined the vehicle will cross the path of this vehicle, the system alerts the driver by flashing the outer rear view mirror indicator lights and sounding the RCTA buzzer (blind spot monitor buzzer).

Y207740E01
0.188,0.573 1.604,0.927 1.417,0.354 10 false Outer Rear View Mirror Assembly LH 0.333,1.396 1.75,1.75 1.417,0.354 10 false Outer Rear View Mirror Indicator Light 2.396,1.094 3.063,1.583 0.667,0.49 10 false Blind Spot Monitor Sensor LH 3.979,1.115 4.646,1.604 0.667,0.49 10 false Blind Spot Monitor Sensor RH 5.083,0.563 6.5,0.917 1.417,0.354 10 false Outer Rear View Mirror Assembly RH 5.219,1.396 6.635,1.75 1.417,0.354 10 false Outer Rear View Mirror Indicator Light 5.073,2.354 6.646,2.719 1.573,0.365 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 0.135,3.531 1.792,3.74 1.656,0.208 10 false Brake Actuator Assembly 0.24,3.927 1.438,4.125 1.198,0.198 10 false Skid Control ECU 0.135,4.552 1.938,4.76 1.802,0.208 10 false Airbag Sensor Assembly 0.229,4.948 1.271,5.146 1.042,0.198 10 false Yawrate Sensor 0.125,5.552 1.635,5.927 1.51,0.375 10 false Spiral Cable with Sensor Sub-assembly 0.229,6.146 1.354,6.354 1.125,0.208 10 false Steering Sensor 0.885,7.104 2.667,7.302 1.781,0.198 10 false : CAN Communication Line 3.26,3.625 3.833,4.646 0.573,1.021 10 false Central Gateway ECU (Network Gateway ECU) 4.885,3.948 5.292,4.135 0.406,0.188 10 false ECM



FUNCTION


a.

Blind Spot Monitor System On/Off Setting

i.

The blind spot monitor system and RCTA can be turned on or off via the setting screen displayed on the multi-information display.

HINT:

It is not possible to enable the RCTA function only.



ii.

The BSM and RCTA indicator lights are located in the combination meter assembly so that the driver can see whether the blind spot monitor system and RCTA are on. When the system is on, the applicable indicator light illuminates.




DIAGNOSIS


a.

The blind spot monitor system is equipped with a diagnosis function that can display warning messages in the multi-information display. For details, refer to the Repair Manual.