FUNCTION OF MAIN COMPONENTS
| Component | Function |
|---|---|
|
*1: Models with panoramic view monitor system *2: Models with simple intelligent parking assist system *3: Models with CVT *4: Models with manual transaxle |
|
| Clearance Warning ECU Assembly | ·
Judges the approximate distance between the vehicle and an obstacle based on signals from the ultrasonic sensors. Output signals are sent to the multi-information display or parking assist ECU*1. ·
Sounds the No. 1 and No. 2 clearance warning buzzer. |
| Front Corner Ultrasonic Sensor (FL) | Detects the distance between the vehicle and an obstacle. |
| Front Corner Ultrasonic Sensor (FR) | |
| Front Center Ultrasonic Sensor (FLC) | |
| Front Center Ultrasonic Sensor (FRC) | |
| Rear Corner Ultrasonic Sensor (RL) | |
| Rear Corner Ultrasonic Sensor (RR) | |
| Rear Center Ultrasonic Sensor (RLC) | |
| Rear Center Ultrasonic Sensor (RRC) | |
| Front Side Ultrasonic Sensor (FLS)*2 | |
| Front Side Ultrasonic Sensor (FRS)*2 | |
| Rear Side Ultrasonic Sensor (RLS)*2 | |
| Rear Side Ultrasonic Sensor (RRS)*2 | |
| No. 1 Clearance Warning Buzzer (Front) | Changes the buzzer sound by controlling the clearance warning ECU assembly, in order to notify the driver of the approximate distance from the vehicle to a stationary object. |
| No. 2 Clearance Warning Buzzer (Rear) | |
| Combination Meter Assembly | ·
Sends an TOYOTA parking assist-sensor on/off signal to the clearance warning ECU assembly. ·
Receives stationary object detection signals from the clearance warning ECU assembly, and displays TOYOTA parking assist-sensor detection on the multi-information display. ·
When TOYOTA parking assist-sensor is off, turns the TOYOTA parking assist-sensor OFF indicator light on. ·
Sends a customization signal to the clearance warning ECU assembly. |
| Radio and Display Receiver Assembly*1 | Displays the location of an obstacle and the approximate distance between the vehicle and the obstacle. |
| Parking Assist ECU*1 | The clearance sonar information is superimposed on the captured image. Then, the image is sent to the radio and display receiver assembly as video signals. |
| Steering Pad Switch Assembly | Sends operation signals from switches to the spiral cable sub-assembly. |
| Spiral Cable with Sensor Sub-assembly | Sends operation signals from the steering pad switch assembly to the combination meter assembly. |
| Park/Neutral Position Switch Assembly*3 | Sends the shift position signal to the ECM. |
| Back-up Light Switch Assembly*4 | Sends an R shift position signal to the ECM. |
| ECM | Sends the shift position signal to the clearance warning ECU assembly. |
| Brake Actuator Assembly
·
Skid Control ECU |
Sends the vehicle speed signal to the clearance warning ECU assembly. |
| Air Conditioner Amplifier Assembly | Sends outside temperature information to the clearance warning ECU assembly. |
SYSTEM CONTROL
Detection Area
The detection areas of the ultrasonic sensor are as shown in the following illustration.
These detection areas are applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.
| *a | Approximately 570 mm (22.4 in.) | *b | Approximately 400 mm (15.7 in.) |
| *c | Approximately 150 mm (5.91 in.) | *d | Sensor Front (Cross Section A) Detection Area (Not Detection Area toward Front/Rear of Vehicle) |
| *e | The detection area in the illustration was calculated using a pole with a diameter of 60 mm (2.36 in.). | - | - |
|
Detection Area | - | - |
| *a | Approximately 1000 mm (39.4 in.) | *b | Approximately 1100 mm (43.3 in.) |
| *c | Approximately 600 mm (23.6 in.) | *d | Approximately 200 mm (7.87 in.) |
| *e | The detection area in the illustration was calculated using a pole with a diameter of 60 mm (2.36 in.). | - | - |
|
Detection Area | - | - |
The operating condition of each sensor differs according to its installed position as shown in the table below:
Ignition switch is ON.
System is activated.
Shift lever is in a position other than P.*
Vehicle speed is approximately 10 km/h (6 mph) or less.
*: Models with CVT
When a stationary object to the side of the vehicle is determined to be within the estimated path of the vehicle, the driver is informed by the multi-information display and by sounding the warning buzzer. (Models with simple intelligent parking assist system)
| *a | Estimated Vehicle Path | *b | When the vehicle is moving rearward. |
| *c | Stationary Object | - | - |
Warning Buzzer Sounding
The warning buzzer sound changes according to the distance from an identified stationary object.
The buzzer sounding interval changes approximately every 100 mm (3.94 in.) according to the distance from the stationary object.
| Identification Level | Detection Distance [mm (in.)] | Buzzer Sound |
|---|---|---|
|
*1: Front center sensor detection only *2: Rear center sensor detection only |
||
| Longest Range | 1000 (39.4) - 600 (23.6)*1
1500 (59.1) - 600 (23.6)*2 |
The sound interval changes every 100 mm (3.94 in.), and then sounds intermittently. |
| Long-range | 600 (23.6) - 450 (17.7) | |
| Medium-range | 450 (17.7) - 300 (11.8) | |
| Short-range | 300 (11.8) - 150 (5.91) | Sounds consecutively. |
| Shortest Range | 150 (5.91) or less | |
If sensors detect multiple stationary objects, the buzzer sounds according to the distance from the closest stationary object.
The TOYOTA parking assist-sensor warning buzzer does not sound if the RCTA warning buzzer is sounding.
FUNCTION
Detection Area Scan Display (Models with Simple Intelligent Parking Assist System)
After turning the ignition switch ON, the scanned detection areas are displayed on the multi-information display.
The detection areas are displayed for 3 seconds after the scan by all ultrasonic sensors is completed.
| *A | When the vehicle is moving forward. | *B | When the vehicle is moving rearward. |
| *a | Scanned Detection Area | *b | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. |
The side detection areas are scanned by the side ultrasonic sensors while the vehicle is moving. Therefore, the side detection areas are not displayed while the vehicle is stopped after turning the ignition switch ON.
TOYOTA Parking Assist-sensor Operation
The combination meter assembly customization setting can be used to turn TOYOTA parking assist-sensor on and off.
A TOYOTA parking assist-sensor OFF indicator light is located in the combination meter assembly to make it possible to check that TOYOTA parking assist-sensor is off.
Warning Buzzer Mute Function
When the warning buzzer is sounding, it is automatically muted if any of the following conditions are established.
There is no change to the distance from the stationary object over a certain period of time.
The distance between the vehicle and stationary object increases.
The stationary object is removed from the path.
When the warning buzzer has been automatically muted, it once again begins sounding if any of the following conditions are established.
A stationary object is detected within short-range.
The vehicle approaches a stationary object.
A stationary object that was out of the path of the vehicle is now on the path of the vehicle.
When the warning buzzer is sounding, the warning buzzer is temporarily muted if the steering pad switch assembly is used to do so.
When the warning buzzer has been temporarily muted, temporary muting is canceled if any of the following conditions are established.
The shift status is changed.
The vehicle speed reaches a certain value or higher.
It cannot be used (CAN communication abnormality).
The ignition switch was turned off.
Abnormality Judgment
When the TOYOTA parking assist-sensor is turned on, abnormality judgment is performed on all sensors regardless of the shift position.
If there is an open or frozen sensor, or if there is a communication malfunction in the clearance warning ECU, a warning is displayed on the multi-information display.
TOYOTA Parking Assist-sensor Settings
The combination meter assembly customization setting can be used to change the volume of the buzzer (3 levels).
The Global TechStream (GTS) can be connected to change settings for some functions as desired by the user. Refer to the Repair Manual for details.
DIAGNOSIS
If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.