Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › from 2019.09
NM32H0E _56 Audio / Visual / Telematics _060816 PARK ASSIST / MONITORING _0406398 PARKING SUPPORT BRAKE SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  CONTROL  PARKING SUPPORT BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*: Models with RCTA function

Front Corner Ultrasonic Sensor (FL) Sends ultrasonic waves to detect stationary objects and outputs a signal to the clearance warning ECU assembly.
Front Corner Ultrasonic Sensor (FR)
Front Center Ultrasonic Sensor (FLC)
Front Center Ultrasonic Sensor (FRC)
Rear Corner Ultrasonic Sensor (RL)
Rear Corner Ultrasonic Sensor (RR)
Rear Center Ultrasonic Sensor (RLC)
Rear Center Ultrasonic Sensor (RRC)
Blind Spot Monitor Sensor LH* Sends a vehicle behind approaching detection signal to the clearance warning ECU assembly.
Clearance Warning ECU Assembly
·

Receives information regarding to a stationary object, etc. in the vehicle traveling direction detected by the ultrasonic sensor, a vehicle approaching the driver's own vehicle from behind detected by the blind spot monitor sensor*, and judges the vehicle condition based on signals from sensors, switches and ECUs located various places to perform parking support brake system control.

·

Sends a parking support brake system control signal to the ECM and skid control ECU.

·

Sends a parking support brake system control status signal, warning request signal and malfunction judgment signal to the combination meter assembly.


Combination Meter Assembly
·

Sends a parking support brake system on/off signal to the clearance warning ECU assembly.

·

Receives a control status signal, warning request signal and combination meter assembly malfunction judgment signal from the clearance warning ECU assembly and displays a message on the multi-information display.

·

Illuminates the PKSB OFF indicator light when the parking support system is off.


ECM
·

Sends a shift position signal, accelerator pedal depression amount signal, etc. to the clearance warning ECU assembly.

·

Performs drive force suppression control in response to a parking support brake system control signal received from the clearance warning ECU assembly.


Brake Actuator Assembly
·

Skid Control ECU


·

Sends wheel speed information, a brake pedal status signal and a master cylinder pressure signal to the clearance warning ECU assembly.

·

Performs brake control in response to a parking support brake system control signal received from the clearance warning ECU assembly.


Airbag Sensor Assembly Sends a lateral acceleration signal, which was detected by the yawrate sensor, to the clearance warning ECU assembly.
Spiral Cable with Sensor Sub-assembly Sends a steering angle signal to the clearance warning ECU assembly.
Air Conditioning Amplifier Assembly Sends an outside temperature signal to the clearance warning ECU assembly.


OPERATING CONDITION


a.

Drive Force Suppression Control

i.

When all of the following conditions are met, drive force suppression control is performed.

Detectable Item Condition

*: Models with RCTA function

Stationary Object
·

The ignition switch is ON.

·

The parking support brake system is on.

·

A stationary object is in the traveling direction of the driver's own vehicle.

·

The vehicle speed is 15 km/h (9 mph) or less.

·

The driver can avoid the object by braking operations.


Vehicle Approaching from Rear*
·

The ignition switch is ON.

·

The parking support brake system is on.

·

The shift position is R.

·

The vehicle speed is 15 km/h (9 mph) or less.

·

An approaching vehicle may collide with the driver's own vehicle.




ii.

When any of the following conditions is met, drive force suppression control is stopped.

Detectable Item Condition

*: Models with RCTA function

Stationary Object
·

The ignition switch is off.

·

The parking support brake system is off.

·

Collision is avoided.

·

A stationary object moves or is moved away from the traveling direction of the driver's own vehicle.


Vehicle Approaching from Rear*
·

The ignition switch is off.

·

The parking support brake system is off.

·

Collision is avoided.

·

A vehicle, which was approaching the driver's vehicle from behind, has moved away.





b.

Brake Control

i.

When all of the following conditions are met, brake control is performed.

Detectable Item Condition
All Objects
·

Drive force suppression control is in operation.

·

Collision is difficult to avoid by braking by the driver.




ii.

When the following conditions are met, brake control is stopped.

Detectable Item Condition

*: Models with RCTA function

Stationary Object
·

The ignition switch is off.

·

The parking support brake system is off.

·

A stationary object moves or is moved away from the traveling direction of the driver's own vehicle.

·

The driver depresses the brake pedal after the vehicle is stopped by brake control.

·

Approximately 2 seconds have elapsed since the vehicle is stopped by brake control.


Vehicle Approaching from Rear*
·

The ignition switch is off.

·

The parking support brake system is off.

·

A vehicle, which was approaching the driver's vehicle from behind, has moved away.

·

The driver depresses the brake pedal after the vehicle is stopped by brake control.

·

Approximately 2 seconds have elapsed since the vehicle is stopped by brake control.



NOTICE:

When brake control operates, the parking support brake system automatically turns off. The system remains off until it is turned on by an operation on the multi-information display screen, the object of brake control goes away, the vehicle reverses approximately 300 mm (11.8 in.) or more*1 or approximately the entire length of the vehicle*2, the vehicle moves forward approximately the entire length of the vehicle*3, or the ignition switch is turned off and back on.

*1: A vehicle approaching from the rear is detected.

*2: A stationary object that is behind the vehicle is detected.

*3: A stationary object is detected.






SYSTEM CONTROL


a.

Parking Support Brake (Stationary Objects) Detection Range

i.

The ultrasonic sensor detects stationary objects that come within approximately 4 m (13 ft.). In addition, the detection distance may differ depending on the shape of the stationary object.


ii.

When the vehicle is moving forward, 2 or more front ultrasonic sensors must simultaneously detect a stationary object for the parking support brake system to operate. Similarly, when the vehicle is moving in reverse, 2 or more rear ultrasonic sensors must detect a stationary object for the system to operate.

Y242370C02
3.844,1.448 4.156,1.604 0.313,0.156 10 false *a 3.135,2.896 3.448,3.052 0.313,0.156 10 false *b 1.969,1.146 2.281,1.302 0.313,0.156 10 false *c 0.729,1.042 1.042,1.198 0.313,0.156 10 false *d 0.24,3.51 0.552,3.667 0.313,0.156 10 false *e 5.094,2.583 5.406,2.74 0.313,0.156 10 false *c 6.333,2.458 6.646,2.615 0.313,0.156 10 false *d
*a While Driving Ahead *b While Reversing
*c Approximately 4 m (13 ft.) *d Object
*e The detection range shown in the illustration is for when detecting an object that is 2 m (6.7 ft.) wide, 1 m (3.3 ft.) tall and is perpendicular to the ground. - -


NOTICE:

Even though the parking support brake system detects stationary objects, it may not operate depending on the vehicle condition.




b.

Parking Support Brake System Control

i.

The parking support brake system determines the state of the vehicle and its surroundings based on signals that the clearance warning ECU assembly receives from sensors, switches and ECUs installed in various locations on the vehicle, and sends the necessary control signals to ECUs to control the vehicle.

Y190224E02
0.729,0.042 2.927,0.344 2.198,0.302 10 false Drive Force Suppression Control 4.927,0.063 5.979,0.438 1.052,0.375 10 false Brake Control 0.438,0.469 3.198,1.104 2.76,0.635 10 false Drive force is suppressed when the operation conditions are met. 3.958,0.469 6.802,1.146 2.844,0.677 10 false Brake control is performed when the operation conditions are met. 1.281,1.573 2.646,1.917 1.365,0.344 10 false Collision is Possible 4.427,1.583 6.604,1.938 2.177,0.354 10 false Possibility of Collision is Very High 0.083,2.406 0.813,2.708 0.729,0.302 10 false Drive Force 1.01,3.188 1.885,3.563 0.875,0.375 10 false Start control 4.542,3.188 5.417,3.563 0.875,0.375 10 false Start control 3.927,2.313 4.406,2.677 0.479,0.365 10 false Braking Force 2.26,2.646 2.896,2.938 0.635,0.292 10 false DOWN 5.875,2.74 6.51,3.031 0.635,0.292 10 false UP 3.073,3.073 3.479,3.365 0.406,0.292 10 false Time 6.625,3.083 7.031,3.375 0.406,0.292 10 false Time


ii.

When the system operates, a warning message is displayed in the multi-information display of the combination meter assembly and the meter buzzer sounds to warn the driver.


iii.

The parking support brake system detects stationary objects using sensors, and when it determines that there is a risk of collision, suppress the drive force.

Drive Force Suppression Control
Y242371E01
0.844,1.24 2.417,1.51 1.573,0.271 10 false Vehicle Condition 1.125,2.031 2.75,2.438 1.625,0.406 10 false Situation 3.052,1.865 4.719,2.406 1.667,0.542 10 false Risk of collision and brake pedal is not depressed 5.094,1.865 6.948,2.333 1.854,0.469 10 false Due to drive force suppression control, vehicle cannot move 0.115,3.135 0.896,4.104 0.781,0.969 10 false Combination Meter Assembly 1.094,2.833 2.719,3.24 1.625,0.406 10 false Multi-information Display 1.042,3.438 2.667,3.844 1.625,0.406 10 false PKSB OFF Indicator Light 1.531,3.938 3.156,4.344 1.625,0.406 10 false Buzzer 3.604,2.833 5.229,3.24 1.625,0.406 10 false BRAKE! 3.375,3.438 5,3.844 1.625,0.406 10 false Not Illuminated 3.604,3.948 4.844,4.344 1.24,0.396 10 false Sounds 5.094,2.729 6.896,3.24 1.802,0.51 10 false Object Detected Acceleration Reduced 0.094,5.188 5.688,5.531 5.594,0.344 10 false This illustration is only for explaining what happens when a stationary object is detected. 5.531,3.438 7.156,3.844 1.625,0.406 10 false Not Illuminated 5.76,3.99 7,4.385 1.24,0.396 10 false Sounds


iv.

When the system determines that there is a high possibility of a collision even after the above operations, brake control is performed in addition to drive force suppression control.

Drive Force Suppression Control and Brake Control 1
Y242372E01
1.188,2.188 2,2.458 0.813,0.271 10 false Situation 0.896,1.021 2.125,1.313 1.229,0.292 10 false Vehicle Condition 2.865,2.021 4.896,2.406 2.031,0.385 10 false High possibility of a collision and brake pedal is not depressed 5.115,1.958 6.958,2.646 1.844,0.688 10 false Vehicle is stopped by system operation and accelerator pedal is depressed 3.625,3.688 4.604,3.938 0.979,0.25 10 false BRAKE! 3.469,4.74 4.552,4.979 1.083,0.24 10 false Not Illuminated 5.656,4.75 6.635,5 0.979,0.25 10 false Illuminates 3.615,5.26 4.229,5.458 0.615,0.198 10 false Sounds 5.74,5.25 6.354,5.448 0.615,0.198 10 false Sounds 5.438,3.906 6.802,4.24 1.365,0.333 10 false Switch to Brake 1.104,3.698 2.906,4 1.802,0.302 10 false Multi-information Display 1.042,4.719 2.896,4.938 1.854,0.219 10 false PKSB OFF Indicator Light 1.604,5.25 3.26,5.469 1.656,0.219 10 false Buzzer 0.115,3.917 0.938,4.51 0.823,0.594 10 false Combination Meter Assembly 0.083,5.99 6.281,6.25 6.198,0.26 10 false This illustration is only for explaining what happens when a stationary object is detected.

Drive Force Suppression Control and Brake Control 2
Y242373E01
1.156,2.146 1.938,2.365 0.781,0.219 10 false Situation 0.896,1.073 2.219,1.323 1.323,0.25 10 false Vehicle Condition 3.74,2.094 6.448,2.625 2.708,0.531 10 false Vehicle is stopped by system operation and accelerator pedal is not depressed 4.594,4.781 5.573,5.031 0.979,0.25 10 false Illuminates 4.667,5.292 5.281,5.49 0.615,0.198 10 false Sounds 1.146,3.708 2.833,4.052 1.688,0.344 10 false Multi-information Display 1.083,4.771 2.854,5.01 1.771,0.24 10 false PKSB OFF Indicator Light 1.729,5.281 3.385,5.5 1.656,0.219 10 false Buzzer 0.167,4 0.99,4.615 0.823,0.615 10 false Combination Meter Assembly 0.083,6.333 6.531,6.604 6.448,0.271 10 false This illustration is only for explaining what happens when a stationary object is detected. 4.344,3.917 6.073,4.302 1.729,0.385 10 false Press Brake Pedal




FUNCTION


a.

Parking Support Brake System Operation

i.

The combination meter assembly customization setting can be used to turn the parking support brake system on and off.


ii.

A PKSB OFF indicator light is added to make it possible to check that the parking support brake system is off in the combination meter assembly. When the parking support brake system is off, the PKSB OFF indicator light illuminates.




FAIL-SAFE


a.

When the clearance warning ECU assembly detects a malfunction in the system, the system enters fail-safe mode. For details, refer to the Repair Manual.



DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the Global TechStream (GTS). Refer to the Repair Manual for details.