FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Models with CVT *2: Models with manual transaxle |
||
| Front Side Ultrasonic Sensor (FLS) | ·
Transmits ultrasonic waves to detect empty parking spaces and sends signals to the clearance warning ECU assembly. ·
Detects the distance between the vehicle and an obstacle. |
|
| Front Side Ultrasonic Sensor (FRS) | ||
| Rear Side Ultrasonic Sensor (RLS) | ||
| Rear Side Ultrasonic Sensor (RRS) | ||
| Front Corner Ultrasonic Sensor (FL) | Detects the distance between the vehicle and an obstacle. | |
| Front Corner Ultrasonic Sensor (FR) | ||
| Front Center Ultrasonic Sensor (FLC) | ||
| Front Center Ultrasonic Sensor (FRC) | ||
| Rear Corner Ultrasonic Sensor (RL) | ||
| Rear Corner Ultrasonic Sensor (RR) | ||
| Rear Center Ultrasonic Sensor (RLC) | ||
| Rear Center Ultrasonic Sensor (RRC) | ||
| Clearance Warning ECU Assembly | Controls the simple intelligent parking assist system based on signals from various switches and sensors. | |
| Combination Meter Assembly | Multi-information Display | Displays the system operation status on the multi-information display. |
| IPA Indicator Light | Illuminates during system operation. | |
| Buzzer | Sounds according to system operating condition. | |
| IPA Main Switch Assembly | ·
Switches between each mode. ·
Depending on the system operating conditions, turns functions off or prohibits assist. |
|
| Power Steering ECU Assembly | ·
Sends power steering control status signals to the clearance warning ECU assembly. ·
Operates the steering based on signals from the clearance warning ECU assembly. |
|
| Park/Neutral Position Switch Assembly*1 | Transmits the shift position signal to the ECM. | |
| Back-up Light Switch Assembly*2 | ||
| ECM | Sends vehicle condition signals such as the engine speed signal and shift position signal to the clearance warning ECU assembly. | |
| Brake Actuator Assembly
·
Skid Control ECU |
Sends the vehicle speed signal to the clearance warning ECU assembly. | |
| Airbag Sensor Assembly | Sends the G information signal to the clearance warning ECU assembly. | |
| Spiral Cable with Sensor Sub-assembly | Sends the steering angle signal to the clearance warning ECU assembly. | |
| Air Conditioner Amplifier Assembly | Sends outside temperature information to the clearance warning ECU assembly. | |
OPERATING CONDITION
Perpendicular Parking Assist Mode
The system starts perpendicular parking assist mode when all of the following conditions are met:
An allowable parking space is detected.
The shift lever is not in P, N or R.*1
The shift lever is not in R.*2
The vehicle is stopped.
Perpendicular parking assist mode is selected using the IPA switch.
*1: Models with CVT
*2: Models with manual transaxle
If the vehicle speed is more than 0 km/h (0 mph), perpendicular parking assist mode cannot be selected (is not displayed). To use perpendicular parking assist mode, operate the IPA switch and select perpendicular parking assist mode with the vehicle completely stopped.
Parallel Parking Assist Mode
The system starts parallel parking assist mode when the vehicle speed is less than 30 km/h (19 mph) (including when the vehicle is stopped) and all of the following conditions are met:
The shift lever is not in P.*1
The shift lever is not in R.*2
Parallel parking assist mode is selected using the IPA switch.
*1: Models with CVT
*2: Models with manual transaxle
Parallel Parking Departure Assist Mode
The system starts parallel parking departure assist mode when all of the following conditions are met:
There is sufficient space to maneuver in front of and behind the vehicle.
The shift lever is in P.*1
When parking in parallel parking assist mode is completed, or the vehicle has not moved after the ignition switch is turned to ON.*2
The vehicle is stopped.
Parallel parking departure assist mode is selected using the IPA switch.
*1: Models with CVT
*2: Models with manual transaxle
SYSTEM CONTROL
Perpendicular Parking Assist Mode
When the vehicle is stopped in front of the target parking space, this system assists the driver in deciding the point at which to start reversing the vehicle into the parking space.
When the IPA switch is pressed while the vehicle is stopped beside the center of a suitable parking space with the parking space detected, guidance information will be displayed on the multi-information display in the combination meter assembly. When the vehicle is driven forward, the steering wheel automatically starts to operate.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When the vehicle reaches the point at which to start reversing, the display changes to instruct the driver to stop the vehicle and move the shift lever to reverse (R).
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When the shift lever has been moved to R, the driver is instructed to reverse the vehicle.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When the vehicle is in the desired position and park (P) is selected, guidance ends.*1
When the vehicle is in the desired position and the IPA switch is operated, guidance ends.*2
*1: Models with CVT
*2: Models with manual transaxle
When it is judged that the vehicle needs to change direction while maneuvering, the driver is instructed to stop the vehicle and then drive the vehicle forward or backward.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When the system judges that the desired parking position has been reached, guidance ends.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Parallel Parking Assist Mode
During parallel parking, this system detects the target parking space and displays the point at which to start reversing the vehicle into the parking space. When the driver reverses the vehicle, the steering wheel automatically starts to operate the vehicle until it is in the target parking position.
When the IPA switch is pressed while the vehicle is driving at low speeds (approximately less than 30 km/h (19 mph)) or the vehicle is stopped, parallel parking guidance information will be displayed on the multi-information display in the combination meter assembly.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Detection of an empty parking space is performed.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When an empty parking space has been detected and it is judged to be suitable, the display changes to instruct the driver to stop the vehicle and move the shift lever to R. When the driver reverses the vehicle according to the guidance, the steering wheel automatically starts to operate.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When it is judged that the vehicle needs to change direction while maneuvering, the driver is instructed to stop the vehicle and then drive the vehicle forward or backward.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When the system judges that the desired parking position has been reached, guidance ends.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Parallel Parking Departure Assist Mode
The system assists the driver when departing from the parallel parking space by operating the steering wheel automatically until the vehicle is out of the parking space.
When the IPA switch is pressed with the shift lever in P, the area surrounding the vehicle is detected and parallel parking departure assist begins.*
*: Models with CVT
When the IPA switch is pressed, the area surrounding the vehicle is detected and parallel parking departure assist begins*
*: Models with manual transaxle
The driver then needs to indicate the departure direction by using the appropriate turn signal.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
The system instructs the driver to move the vehicle forward or backward. When the driver changes the shift status according to the guidance, the steering wheel automatically starts to operate.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When it is judged that the vehicle needs to change direction while maneuvering, the system instructs the driver to stop the vehicle and the move the vehicle forward or backward.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
When the system judges that the vehicle has departed, guidance ends.
| *a | This Vehicle | *b | Multi-information Display |
| *c | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
Warning Message
The following messages are displayed on the multi-information display when the simple intelligent parking assist system cannot operate.
| Warning Message | Description |
|---|---|
| IPA System Check Visit Your Dealer | The system may be malfunctioning. |
| Currently Unavailable | There may be a system failure. |
| Power steering equipment is temporarily overheating. | |
| Ice, snow, dirt, etc., has adhered to the ultrasonic sensor. | |
| The ultrasonic sensor is frozen. | |
| The battery has been removed and reinstalled. | |
| Excessive speed | The IPA switch is operated when the vehicle speed exceeds 30 km/h (19 mph). |
| Narrow Space Try Another Location | The IPA switch is operated at a space that is too narrow for the vehicle to park in. |
| Obstruction Try Another Location | The IPA switch is operated in an area where there are obstacles to the front, and the vehicle cannot move forward to the starting point for backing up. |
| Unavailable Try Another Location | The IPA switch is operated in an area with no parking spaces. |
| The IPA switch is operated in an area where the road width for parking is narrow. | |
| Narrow Space | The IPA switch is operated when there is not enough space to the front and rear of the vehicle when departing from a parallel parking spot. |
| Unavailable | The IPA switch is operated in an area where there are obstacles to the sides and the vehicle cannot depart from the parallel parking spot. |
| Pressure Applied to Steering Wheel | Assist control is started while the steering wheel is held. |
| Stop the Vehicle | The vehicle is moved and assist control is started while the steering wheel is held. |
The following messages are displayed on the multi-information display when the simple intelligent parking assist system is canceled.
| Warning Message | Description |
|---|---|
| Park Assist Cancelled | While assist control is operating, the driver changes the shift position to P or operates the IPA switch. |
| Excessive speed | The vehicle speed exceeds 30 km/h (19 mph) when searching for a parallel parking assist mode space. |
| Narrow Space | Assist control is started in an area with narrow parking spaces. |
| Wrong Direction | When assist control starts, the vehicle proceeds in a direction opposite to the guidance. |
| No Exit Direction Specified | The shift position is changed without having used the turn signal lever to select a departure direction when using the parallel parking departure assist mode. |
| Cannot Reach Desired Position | The maximum number of movements for multi-turn maneuvering is reached during assist control, or the target parking spot cannot be reached due to the control being used on a road with steep grade. |
The following messages are displayed on the multi-information display when the simple intelligent parking assist system is suspended.
| Warning Message | Description |
|---|---|
| Steering Wheel Turned | The driver holds the steering wheel during assist control. |
| Excessive speed | The vehicle speed exceeds 7 km/h(4.3 mph) during assist control. |
| Pressure Applied to Steering Wheel | The IPA switch is pressed to start assist control when the steering wheel is held onto with assist control temporarily stopped. |
| Too Close to Obstacle at Front | The vehicle moved too close to an obstacle in front of the vehicle. |
| Too Close to Obstacle at Rear | The vehicle moved too close to an obstacle behind the vehicle. |
| Stop the Vehicle | The IPA switch is pressed to start assist control while the vehicle is moved with assist control temporarily stopped. |
The following message is displayed on the multi-information display when the vehicle speed exceeds 4.3 km/h (2.7 mph) during assist control.
| Warning Message | Description |
|---|---|
| Excessive speed Slow Down | The vehicle speed exceeds 4.3 km/h (2.7 mph) during assist control. |
FUNCTION
Parking Space Detection
Parking spaces are detected based on signals from the front and rear side ultrasonic sensors.
| *a | This Vehicle | *b | Parking Space |
| *c | The illustration shown is an example only. | - | - |
Multi-information Display
When the system is operating, the following screen is displayed on the multi-information display in the combination meter assembly.
| *a | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
| Item | Description | |
|---|---|---|
| (1) | Operation Display Area | Displays the operating condition of the simple intelligent parking assist system. |
| (2) | Steering Wheel AUTO Operation Display | Displays when the steering wheel AUTO operation is being performed. |
| (3) | Advice Display | Follow the instructions on the display and perform any indicated operations. |
| (4) | IPA Switch Icon | Displays when the assist mode can be changed and the assist control can be started using the IPA switch. |
| (5) | Clearance Sonar Display | If an obstacle is detected when the TOYOTA parking assist-sensor system is activated, the approximate distance between the vehicle and the obstacle is displayed. |
| (6) | Stop Display | When illuminated, depress the brake pedal and stop the vehicle at once. |
| (7) | Assistance Level Indicator | Displays a gauge indicating the level until the vehicle's stopping position/the position at which assist control ends. |
Assist Mode Selection (Models with CVT)
When the shift lever is not in P, N or R, perpendicular parking assist mode* or parallel parking assist mode can be selected using the IPA.
*: Can only be selected when the operating conditions of perpendicular parking assist mode are met.
When the shift lever is in P, parallel parking departure assist mode can be selected using the IPA switch.
The multi-information display of the combination meter assembly displays each mode display.
| *a | Parallel Parking Assist Mode | *b | Perpendicular Assist Mode (guidance to move forward) (Only when the operating conditions are met.) |
| *c | System Off (Assist mode is not selected.) | *d | The illustrations shown are examples only. The illustration may differ from the actual vehicle screens. |
|
IPA Switch Operation | - | - |
| *a | Parallel Parking Departure Assist Mode | *b | System Off (Assist mode is not selected.) |
| *c | The illustrations shown are examples only. The illustration may differ from the actual vehicle screens. | - | - |
|
IPA Switch Operation | - | - |
Assist Mode Selection (Models with Manual Transaxle)
When the shift lever is not in R, perpendicular parking assist mode* or parallel parking assist mode can be selected using the IPA switch.
*: Can only be selected when the operating conditions of perpendicular parking assist mode are met.
When parking in Parallel Parking Assist Mode is completed, or the vehicle has not moved after the ignition switch is turned to ON, parallel parking departure assist mode can be selected using the IPA switch.
The multi-information display of the combination meter assembly displays each mode display.
| *a | Parallel Parking Assist Mode | *b | Perpendicular Assist Mode (guidance to move forward) (Only when the operating conditions are met.) |
| *c | System Off (Assist mode is not selected.) | *d | The illustrations shown are examples only. The illustration may differ from the actual vehicle screens. |
|
IPA Switch Operation | - | - |
| *a | Parallel Parking Departure Assist Mode | *b | System Off (Assist mode is not selected.) |
| *c | The illustrations shown are examples only. The illustration may differ from the actual vehicle screens. | - | - |
|
IPA Switch Operation | - | - |
Parking Support Brake System Operation
Regardless of whether the parking support brake system is set to off, when the simple intelligent parking assist system is operating and the operating conditions of the parking support brake system are met, brake control is performed and operation of the simple intelligent parking assist system is suspended.
When the simple intelligent parking assist system is suspended due to brake control being performed by the parking support brake system, the buzzer sounds and the operation status of the parking support brake system is displayed on the multi-information display in the combination meter assembly.
After cancellation of the parking support brake system, if the operating conditions are met, the simple intelligent parking assist system can be operated again by pressing the IPA switch.
When the simple intelligent parking assist system is operating, if the parking support brake system performs brake control 3 times or more, operation of the simple intelligent parking assist system is canceled.
| *a | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
TOYOTA Parking Assist-sensor System Operation
Regardless of whether the TOYOTA parking assist-sensor system is set to off, when the simple intelligent parking assist system is operating and the operating conditions of the TOYOTA parking assist-sensor system are met, the buzzer sounds and the clearance sonar obstruction detection screen is displayed on the multi-information display in the combination meter assembly.
| *a | Clearance Sonar Obstruction Detection Screen | *b | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. |
DIAGNOSIS
If a system malfunction is detected, the clearance warning ECU assembly stores Diagnostic Trouble Codes (DTCs) in its memory. For details, refer to the Repair Manual.