Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2019.09
NM32H0E _59 Vehicle Exterior _060808 LIGHTING (EXT) _0298246 LIGHTING SYSTEM CO CONTROL F

LIGHTING (EXT)  LIGHTING SYSTEM  CONTROL  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function

*1: Models with static control type automatic headlight beam level control system

*2: Models with dynamic control type automatic headlight beam level control system

Headlight ECU Sub-assembly LH
·

Controls the automatic headlight beam level control system.

·

Detects the vehicle posture and vehicle driving conditions based on the rear height control sensor sub-assembly LH and skid control ECU to control the headlight leveling motor LH*1 or headlight swivel motor LH*2.


Headlight ECU Sub-assembly RH Controls the headlight leveling motor RH*1 or headlight swivel motor RH*2 according to control signals from the headlight ECU sub-assembly LH.
Headlight Leveling Motor LH/RH*1 Moves the headlights vertically and controls the beam axis direction according to control signals from the headlight ECU sub-assembly LH/RH.
Headlight Swivel Motor LH/RH*2 Moves the headlights vertically and controls the beam axis direction according to control signals from the headlight ECU sub-assembly LH/RH.
Brake Actuator Assembly
·

Skid Control ECU


Transmits the vehicle speed signal to the headlight ECU sub-assembly LH.
Rear Height Control Sensor Sub-assembly LH Detects vehicle movement and transmits a signal to the headlight ECU sub-assembly LH.
Headlight Dimmer Switch Assembly Transmits a light control signal to the main body ECU (multiplex network body ECU).
Main Body ECU (Multiplex Network Body ECU) Receives a light control signal and transmits it to the headlight ECU sub-assembly LH.


SYSTEM CONTROL


a.

Static Control Type

i.

The headlight ECU sub-assembly LH receives vehicle height change signals sent from the rear height control sensor sub-assembly LH and calculates the changes in the pitch angle of the vehicle. The headlight ECU sub-assembly LH/RH drives the headlight leveling motor LH/RH in accordance with the change.

Control Mode Details
While Stopped If the vehicle attitude is stable for approximately 3 seconds with the headlights on while stopped, the headlight ECU sub-assembly LH/RH operates the headlight leveling motor LH/RH in accordance with the detected change in vehicle attitude.



b.

Dynamic Control Type

i.

The headlight ECU sub-assembly LH receive changes in the height of the vehicle which is detected by the rear height control sensor LH and calculate the change in pitch of the vehicle.


ii.

The headlight ECU sub-assemblies adjust the vertical aim of the headlights based on the calculated angle of the vehicle in order to maintain a constant beam angle.

Y194545E01
1,1.625 1.177,1.208 1.177,1.208 1.417,1.208 false 1.094,2.167 1.208,2.5 1.208,2.5 1.375,2.5 false 4.646,1.698 4.823,1.281 4.823,1.281 5.063,1.281 false 4.531,1.99 4.677,2.521 4.677,2.521 4.865,2.521 false 0.042,0.594 0.979,0.896 0.938,0.302 10 false Vehicle Speed 3.354,0.635 4.302,0.927 0.948,0.292 10 false Vehicle Speed 0.063,1.833 0.813,2.469 0.75,0.635 10 false Base Beam Angle 3.583,1.823 4.323,2.375 0.74,0.552 10 false Base Beam Angle 3.302,2.885 3.74,3.167 0.438,0.281 10 false Time 6.698,2.844 7.135,3.125 0.438,0.281 10 false Time 4.469,3.135 7.021,3.771 2.552,0.635 10 false Models with Automatic Headlight Leveling Control (Dynamic Control Type) 1.052,3.073 3.302,3.594 2.25,0.521 10 false Models without Automatic Headlight Leveling Control 1.458,1.135 3.177,1.5 1.719,0.365 10 false Change in vehicle speed 1.417,2.427 3.458,2.719 2.042,0.292 10 false Deviation from Base Beam Angle 5.125,1.208 6.844,1.573 1.719,0.365 10 false Change in vehicle speed 4.906,2.448 6.948,2.74 2.042,0.292 10 false Deviation from Base Beam Angle




FUNCTION


a.

Static Control Type

i.

The rear height control sensor sub-assembly LH detects the changes in vehicles rear ride height due to cargo loads etc., and operates the headlight leveling motor RH/LH in accordance with the changes, keeping the headlight axes at a constant angle.



b.

Dynamic Control Type

i.

The headlight ECU sub-assemblies calculates changes in the vehicle posture based on the signals from the rear height control sensor sub-assembly LH.


ii.

Following this, the ECUs controls the headlight swivel motor based on this information, in order to change the projector headlight unit angle.




FAIL-SAFE


a.

If the headlight ECU sub-assembly detects a malfunction in the automatic headlight beam level control system, the headlight ECU sub-assembly performs the fail-safe operation. For details, refer to the Repair Manual.