FUNCTION
Buzzer
The table below shows the warning and reminder functions of the buzzer in the combination meter assembly.
|
*1: Models with simple intelligent parking assist system *2: Models with entry and start system *3: Models with CVT *4: Models without entry and start system *5: Models with Toyota safety sense *6: Models with speed limiter control system *7: Models with road sign assist system |
|
| Priority | Item |
| 1 | Simple Intelligent Parking Assist Indication Pattern 1 (Once)*1 |
| 2 | Simple Intelligent Parking Assist Indication Pattern 1 (Twice)*1 |
| 3 | Simple Intelligent Parking Assist Indication Pattern 2 (Once)*1 |
| 4 | Simple Intelligent Parking Assist Indication Pattern 2 (Twice)*1 |
| 5 | Simple Intelligent Parking Assist Indication Pattern 3 (Once)*1 |
| 6 | Engine Stall Warning*2 |
| 7 | Engine Stall Warning*4 |
| 8 | Entry and Start System Warning (Intermittent)*2 |
| 9 | Reverse Notification |
| 10 | Door Open when Shift Lever not in P Warning*2, *3 |
| 11 | Key Reminder*4 |
| 12 | Brake Fluid Low Warning |
| 13 | EPS Warning (Intermittent) |
| 14 | Engine Switch Operation while Driving Warning*2 |
| 15 | Vehicle Roll-away Notification Pattern 2 |
| 16 | Lane Departure Alert Warning*5 |
| 17 | Warning Buzzer for Shift Lever in P Advice*2, *3 |
| 18 | Vehicle Roll-away Notification Pattern 1 |
| 19 | Parking Brake Engaged Warning |
| 20 | Speed Limit Exceed Warning*6 |
| 21 | Engine Oil Pressure Warning |
| 22 | Hands off Steering Wheel Warning*5 |
| 23 | Lane Departure Alert System Cancel Warning*5 |
| 24 | Seat Belt Warning (Level 2) |
| 25 | Seat Belt Warning (Level 1) |
| 26 | Alert Buzzer for Driving with Door Ajar |
| 27 | Entry and Start System Warning (Intermittent, Maximum 9 Times)*2 |
| 28 | Engine Start while Driving Notice*2 |
| 29 | Sport Shift Reject Warning*3 |
| 30 | Low Speed Zone Leading Vehicle Lost Warning*5 |
| 31 | Dynamic Radar Cruise Control Cancellation due to Low Speed Warning*5 |
| 32 | Vehicle Sway Warning*5 |
| 33 | Road Sign Assist Indication*7 |
| 34 | EPS Warning (Once) |
| 35 | Engine Coolant Temperature Warning |
| 36 | Brake Hold Warning |
| 37 | Multi-information Display Warning |
| 38 | Engine Malfunction Warning |
| 39 | Light Reminder |
| 40 | Entry and Start System Warning (Once)*2 |
| 41 | Immobiliser Certification Reminder*2 |
| 42 | Turn Signal/Hazard Warning Operation |
Multi-information Display
Display Function Flow
The multi-information display can be switched as shown in the flow chart below:
| Item | Display Change Condition |
|---|---|
| *a | Conditions are met. |
| *b | Conditions are not met. |
| *c | If there are multiple display requests, items will be displayed in sequence |
| *d | Item or display is selected by operating the steering pad switch |
| *e | After engine start |
| *f | The ending display is displayed for a certain period of time after the ignition switch is turned off. |
Display Tab Operation
The information currently displayed can be switched using the RIGHT/LEFT switch of the steering pad switch assembly.
| *A | Models with Navigation System | *B | Models with Display Audio System |
| *C | Models with Toyota Safety Sense | - | - |
| *1 | Steering Pad Switch Assembly | - | - |
| *a | LEFT Switch | *b | RIGHT Switch |
| *c | Drive Information Tab | *d | Navigation Information Tab |
| *e | Audio Information Tab | *f | Driving Assist System Information Tab |
| *g | Warning Message Tab | *h | Setting Tab |
| *i | The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen. | - | - |
|
RIGHT switch operation |
|
LEFT switch operation |
Drive Information
The drive information tab shows vehicle information such as drivable range and fuel consumption.
The drive information display can be changed using the UP/DOWN switch of the steering pad switch assembly.
| *A | Models with CVT | *B | AWD Models |
| *C | 2WD Models | - | - |
| *1 | Steering Pad Switch Assembly | - | - |
| *a | UP Switch | *b | DOWN Switch |
| *c | Drive Information 1 | *d | Drive Information 2 |
| *e | Eco Driving Indicator Zone Display | *f | Digital Vehicle Speed and Cruising Range Display |
| *g | AWD Control Display | *h | G Monitor |
| *i | Blank | *j | The illustrations shown are examples only. The illustrations may differ from the actual vehicle screen. |
|
DOWN switch operation |
|
UP switch operation |
Setting Function
The following items can be selected on the information setting screen.
| Item | Available Setting |
|---|---|
| Steering Assist | Setting for steering assist can be set to on/off: -
On -
Off |
| Warning Sensitivity | Alert sensitivity of alert system can be changed: -
High -
Standard |
| Vehicle Sway Warning | Vehicle sway warning can be selected: -
On -
Off |
| Vehicle Sway Warning Sensitivity | Vehicle sway warning sensitivity can be selected: -
High -
Standard -
Low |
| Item | Available Setting |
|---|---|
| PCS | The pre-collision system can be set to on/off: -
On -
Off |
| The pre-collision system warning timing | The pre-collision system warning timing can be selected: -
Far (Icon is displayed) -
Middle (Icon is displayed) -
Near (Icon is displayed) |
| Item | Available Setting |
|---|---|
| BSM | The blind spot monitor system can be set to on/off: -
ON -
OFF |
| RCTA | The RCTA function can be set to on/off: -
ON -
OFF
|
| Item | Available Setting |
|---|---|
| TOYOTA Parking Assist-sensor System | The parking support alert system can be set to on/off: -
On -
Off |
The buzzer volume can be selected: -
1 (Icon is displayed) -
2 (Icon is displayed) -
3 (Icon is displayed) |
| Item | Available Setting |
|---|---|
| PKSB | The parking support brake system can be set to on/off: -
On -
Off |
| Item | Available Setting |
|---|---|
| Road Sign Assist | The road sign assist system can be set to on/off: -
ON -
OFF |
| Item | Available Setting |
|---|---|
| Drive Mode | The drive mode can be changed: -
SPORT -
NORMAL -
ECO |
| Item | Available Setting |
|---|---|
| Display Brightness | Select to adjust brightness of the instrument panel light. |
| Item | Available Setting | |
|---|---|---|
|
*1: Models with road sign assist system *2: Models with tire pressure warning system |
||
| Road Sign Assist Setup*1 | Notification Method | Select to change the notification method of the following warnings between No Notification, Only Visual and Visual and Audible: -
Excess Speed Warns the driver if the vehicle exceeds the speed on the speed limit sign displayed on the multi-information display. -
Others Warns the driver if the system determines that the vehicle is overtaking when a no overtaking sign is displayed on the multi-information display. |
| Notification Level | Select to set the speed threshold over which the excess speed warning starts to operate when a speed limit sign is displayed on the multi-information display. -
2 km/h (1 mph) -
5 km/h (3 mph) -
10 km/h (5 mph) |
|
| TPMS Setup*2 | The tire pressure monitor system can be initialized. | |
| Item | Available Setting |
|---|---|
|
*1: Models with CVT *2: Models with display audio system |
|
| Language | The language used on the multi-information display can be selected: -
English (Default) -
German -
French -
Spanish -
Italian -
Portuguese -
Dutch -
Swedish -
Norwegian -
Danish -
Russian -
Finnish -
Greek -
Polish -
Ukrainian -
Turkish -
Hungarian -
Czech -
Slovak -
Romanian |
| Unit | The unit displayed on the multi-information display can be selected: -
km (km/L) -
km (L/100 km) -
miles (MPG) |
| Eco Driving Indicator Light*1 | The Eco Driving Indicator Light can be switched: -
ON (Default) -
OFF |
| Drive Information 1 | 2 items can be selected among the following: -
Current Fuel Consumption (Bar Display) (Default of upper area) -
Current Fuel Consumption (Value Display) -
Total Average Fuel Consumption between Rest Operations (Default of lower area) -
Average Fuel Consumption after Engine Startup -
Average Fuel Consumption after Refueling -
Total Average Vehicle Speed between Reset Operations -
Average Vehicle Speed after Engine Start-up -
Total Elapsed Time between Reset Operations -
Elapsed Time after Engine Start-up -
Cruising Range -
Cruising Range after Engine Start-up -
Blank |
| Drive Information 2 | 2 items can be selected among the following: -
Current Fuel Consumption (Bar Display) -
Current Fuel Consumption (Value Display) -
Total Average Fuel Consumption between Rest Operations -
Average Fuel Consumption after Engine Startup -
Average Fuel Consumption after Refueling -
Total Average Vehicle Speed between Reset Operations (Default of lower area) -
Average Vehicle Speed after Engine Start-up -
Total Elapsed Time between Reset Operations -
Elapsed Time after Engine Start-up -
Cruising Range (Default of upper area) -
Cruising Range after Engine Start-up -
Blank |
| Interruption Display | The following displays that appear as soon as the set conditions are met can be switched to ON (Default) or OFF: -
Incoming Telephone Display*2 |
| Initialization | The set items can be initialized. |
Warning Mode Function
When a warning is necessary, the warning display interrupts the current display on the multi-information display.
The master warning light may illuminate or blink* and the buzzer in the combination meter assembly may sound depending on the item displayed on the multi-information display.
*: Models with TFT monochrome multi-information display
| Priority | Display | Buzzer |
|---|---|---|
|
*1: AWD models *2: Models with Toyota safety sense *3: Models with entry and start system *4: Models with CVT *5: Models with manual transaxle *6: Models with Toyota parking assist-sensor system *7: Models with Parking Support Brake System *8: Models with blind spot monitor system *9: Models with cruise control system *10: Models with speed limiter control system *11: Models with road sign assist system *12: Models with Projector Headlight *13: Models with washer fluid level warning system *14: Models with 8NR-FTS engine |
||
| 1 | 4WD(AWD) TEST MODE*1 | - |
| ADJUSTING LDA CAMERA*2 | - | |
| ADJUSTING FRONT RADAR BEAM*2 | - | |
| ADJUSTING FRONT RADAR BEAM ERROR*2 | - | |
| ADJUSTING FRONT RADAR BEAM ALONG VERTICAL AXIS*2 | - | |
| ADJUSTING FRONT RADAR BEAM ALONG HORIZONTAL AXIS*2 | - | |
| CHECKING CRUISE CONTROL BRAKE*2 | - | |
| CHECKING PCS BRAKE*2 | - | |
| Headlight system Uninitialized. Visit your dealer.*12 | - | |
| BRAKE!*2 | - | |
| Push and Hold ENGINE Switch for Emergency Stop*3 | - | |
| Shift to N Position & Push ENGINE Switch to Restart*3, *4 | - | |
| Depress Clutch Pedal & Push ENGINE Switch to Restart*3, *5 | - | |
| Engine Stopped. Shift to P Position*3, *4 | - | |
| Engine Stopped. Stop in a Safe Place.*3 | - | |
| 2 | Switch to Brake.*7 | Sounds |
| Press brake pedal*7 | Sounds | |
| BRAKE!*7 | Sounds | |
| Object Detected, Acceleration Reduced.*7 | Sounds | |
| 3 | Shift to P Before Exiting Vehicle*3 | Sounds |
| Parking assist Malfunction Visit your dealer*6 | Sounds | |
| Parking assist unavailable. Clean parking assist sensor*6 | Sounds | |
| Parking assist unavailable.*6 | Sounds | |
| Check Fuel Cap | Sounds | |
| Speed Limit Exceeded*10 | - | |
| 4 | Power Steering Malfunction. Steering Power Low. Visit Your Dealer. | Sounds |
| Power Steering Malfunction. Steering Power Low. Visit Your Dealer. | Sounds | |
| Abnormal Voltage. Steering Power Low. Visit Your Dealer. | Sounds | |
| Abnormal Voltage. Steering Power Low. Visit Your Dealer. | Sounds | |
| Power Steering Malfunction. Visit Your Dealer. | Sounds | |
| EPB Applied. | Sounds | |
| Vehicle May Roll Out. Shift to P.*4 | Sounds | |
| Brake Hold Fault. Depress Brake to Deactivate. Visit Your Dealer. | Sounds | |
| Brake Hold Warning. Depress Brake on Slope | Sounds | |
| EPB Activation Incomplete. | Sounds | |
| Key Not Detected, Check Key Location.*3 | Sounds | |
| EPB Release Unavailable, Depress Brake Pedal for EPB Release. | Sounds | |
| Release Accelerator. | Sounds | |
| 5 | LDA. Driver Attention Required.*2 | Sounds |
| LDA. Hold Steering Wheel.*2 | - | |
| LDA Steering Assist Unavailable, Hold Steering Wheel.*2 | Sounds | |
| LDA. Hold Steering Wheel.*2 | Sounds | |
| EPB Frequently Operated, Wait a Minute. | Sounds | |
| 6 | Check Engine. Visit Your Dealer. | - |
| Check Engine. Reduced Engine Power. Visit Your Dealer. | - | |
| Reduced Engine Power. Visit Your Dealer. | - | |
| Engine Maintenance Required. Visit Your Dealer. | - | |
| Engine Stopped. Stop in a Safe Place. | Sounds | |
| Engine Stopped. Shift to P.*4 | Sounds | |
| Engine Stopped. Shift to N.*4 | Sounds | |
| Strongly Depress Brake And Then Start Engine. | Sounds | |
| Depress Brake and Then Start Engine.*4 | Sounds | |
| Depress Clutch and Then Start Engine.*5 | Sounds | |
| Antilock Brake System Malfunction. Visit Your Dealer. | Sounds | |
| Engine Coolant Temperature High. Stop in a Safe Place. See Owner's Manual. | Sounds | |
| Vehicle May Roll Out. Park The Vehicle on Flat Road. | Sounds | |
| Charging System Malfunction. Stop in a Safe Place. See Owner's Manual. | Sounds | |
| Clean Radar Sensor.*2 | Sounds | |
| Cruise Control unavailable.*2 | Sounds | |
| Cruise Control Unavailable. Depress The Brake Pedal.*2 | - | |
| Cruise Control Off. Shifted to P Position. Depress The Brake Pedal and Shift to D to Restart.*2, *4 | Sounds | |
| LDA Unavailable.*2 | Sounds | |
| Entry & Start System Malfunction. See Owner's Manual.*2 | Sounds | |
| Blind Spot Monitor Unavailable.*8 | Sounds | |
| Check Cruise Control System. Visit Your Dealer.*9 | Sounds | |
| Check Cruise Control System. Depress The Brake Pedal. Visit Your Dealer.*9 | Sounds | |
| Check Speed Limiter System.*10 | Sounds | |
| Lane Departure Alert Malfunction. Visit Your Dealer.*2 | Sounds | |
| Front Camera Unavailable.*2 | Sounds | |
| LDA ON. Steering Assist Active.*2 | - | |
| LDA ON. Steering Assist Inactive.*2 | - | |
| Front Camera Vision Blocked. Clean and Demist Windshield.*2 | Sounds | |
| Pre-Collision System Malfunction. Visit Your Dealer.*2 | Sounds | |
| Blind Spot Monitor System Malfunction. Visit Your Dealer.*8 | Sounds | |
| Engine Oil Pressure Low. Stop in a Safe Place. See Owner's Manual. | Sounds | |
| AWD System Malfunction. 2WD Mode Engaged Visit Your Dealer.*1 | Sounds | |
| EPB Unavailable. | Sounds | |
| Check RSA System.*11 | Sounds | |
| EPB Malfunction. Visit Your Dealer. | Sounds | |
| For Motorway Use Only. Beware of Stopping or Merging Vehicles!*2 | - | |
| LDA Unavailable Below Approx. 50 km/h.*2 | - | |
| LDA Unavailable Below Approx. 32 MPH.*2 | - | |
| LDA Unavailable at Current Speed.*2 | - | |
| 7 | Engine Stopped. Steering Power Low. | Sounds |
| Turn Power Off.*3 | Sounds | |
| Would You Like To Take A Rest?*2 | Sounds | |
| Please Take A Rest.*2 | Sounds | |
| Key Detected in Vehicle.*3 | - | |
| Turn Lights Off. | Sounds | |
| Window Open. | Sounds | |
| Depress Brake Pedal and Touch ENGINE Switch with Key.*3, *4 | Sounds | |
| Depress Clutch Pedal and Touch ENGINE Switch with Key.*3, *5 | Sounds | |
| Not Ready to Drive. Depress Brake Pedal & Push ENGINE Switch to Start.*3, *4 | - | |
| Not Ready to Drive.*3, *5 | - | |
| Depress Brake Pedal & Push ENGINE Switch to Start.*3, *4 | - | |
| Depress Clutch Pedal & Push ENGINE Switch to Start.*3, *5 | - | |
| Push ENGINE Switch while Turning The Steering Wheel in Either Direction.*3 | Sounds | |
| 8 | Brake Hold Malfunction. Visit Your Dealer. | Sounds |
| Brake Hold Less Effective during Icy Conditions. | - | |
| Brake Hold Active. Depress Brake and Switch to Deactivate. | Sounds | |
| Brake Hold Unavailable. Driver Door Open. | Sounds | |
| EPB Can't be Released. Close Door and Fasten Your Seatbelt. | Sounds | |
| Brake Hold Unavailable. Driver Seat Belt Unbuckled. | Sounds | |
| Brake Hold Unavailable. Hood or Trunk Open. | Sounds | |
| Depress Brake to Maintain Brake Hold. | Sounds | |
| Close Driver Door to Maintain Brake Hold. | Sounds | |
| Fasten Driver Seat Belt to Maintain Brake Hold. | Sounds | |
| Brake hold unavailable. | - | |
| Brake hold deactivated | Sounds | |
| Brake hold deactivated. Parking brake automatically applying | Sounds | |
| EPB Automatically Applied. | Sounds | |
| AWD System Overheated. 2WD Mode Engaged.*1 | Sounds | |
| AWD System Overheated. Switching to 2WD Mode.*1 | Sounds | |
| ICS Malfunction. Visit Your Dealer.*7 | Sounds | |
| Parking Support Brake Malfunction Visit Your Dealer*7 | Sounds | |
| Drive-Start Control Malfunction. Visit Your Dealer. | Sounds | |
| Brake Override Malfunction. Visit Your Dealer. | Sounds | |
| Reverse Speed Control Activated. | Sounds | |
| ICS Unavailable.*7 | - | |
| Parking Support Brake Unavailable*7 | - | |
| Parking Support Brake Unavailable Remove the Dirt of Rear Camera*7 | - | |
| 9 | RCTA Malfunction Visit Your Dealer.*7 | Sounds |
| RCTA Unavailable.*7 | Sounds | |
| Key Battery Low. Replace Key Battery.*3 | Sounds | |
| Engine Oil Level Low. Add or Replace Oil. | - | |
| Headlight System Malfunction. Visit Your Dealer.*12 | Sounds | |
| Accelerator and Brake Pedals Depressed Simultaneously. | - | |
| 10 | CHECKING PCS BRAKE*2 | - |
| Low Washer Fluid.*13 | - | |
| Traction Control Turned OFF. | - | |
| Oil Maintenance Required Soon.*14 | - | |
| Oil Maintenance Required Visit Your Dealer.*14 | - | |
| To Activate AHB, Switch Headlights to High Beam.*2 | - | |
| Resetting Oil Maintenance Data.*14 | - | |
| Resetting of Oil Maintenance Data Incomplete.*14 | - | |
| Depress Brake Pedal & Push ENGINE Switch to Start.*3, *4 | - | |
| Depress Clutch Pedal & Push ENGINE Switch to Start.*3, *5 | - | |
| VSC Turned Off. Pre-Collision Brake System Unavailable.*2 | - | |
| Pre-Collision System Unavailable.*2 | - | |
| Front Camera Unavailable.*2 | - | |
| Front Camera Vision Blocked. See Owner's Manual.*2 | - | |
| Pre-Collision System Unavailable.*2 | - | |
| Pre-Collision System Unavailable. Clean Sensor.*2 | - | |
| iMT System Malfunction. Visit Your Dealer.*5 | - | |
| Depress The Accelerator Pedal When Starting Off.*5 | - | |
| EPB Shift Interlock Function Activated. | Sounds | |
| EPB Shift Interlock Function Deactivated. | Sounds | |
| Pre-Collision System Off.*2 | - | |
| 11 | A New Key has been Registered. Contact Your Dealer for Details.*3 | - |
OPERATION
Eco Driving Indicator Light and Eco Driving Indicator Zone Display (Models with CVT)
The following table shows the operation of Eco Driving Indicator Light and Eco Driving indicator zone display in different driving conditions:
| Driving Condition | Eco Driving Indicator Light | Eco Driving Indicator Zone Display |
|---|---|---|
| While Stopped | Turns off |
|
| While Eco Driving | Turns on |
|
| While Non-eco Driving | Turns off |
|
| When any of the following conditions is met, operation is stopped.
·
Ignition switch off ·
Engine stopped. ·
Shift lever is not in D. ·
Normal or Eco mode is not selected. ·
The vehicle is being driven at a speed of 130 km/h (81 mph) or higher. |
Turns off |
|