Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › 2020.08–2022.01
NM32H0E _51 Engine / Hybrid System _059914 CRUISE CONTROL _0293939 ROAD SIGN ASSIST SYSTEM CO CONTROL F

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  CONTROL  ROAD SIGN ASSIST CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components in the RSA have the following functions.

Components Function

*1: The threshold can be adjusted to 1 of 3 levels through the customization function.

*2: Models for Europe

*3: Models with navigation system

Forward Recognition Camera
·

Captures road signs.

·

Performs RSA system control based on information of road signs captured by the camera sensor.

·

Controls the supply of electric current to the forward recognition hood with heater sub-assembly when the ambient temperature is low.


Forward Recognition Hood with Heater Sub-assembly Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
ECM Sends the shift position signal to the forward recognition camera.
Brake Actuator Assembly Skid Control ECU Sends a vehicle speed signal from the speed sensor to the forward recognition camera.
Combination Meter Assembly Multi-information Display
·

Displays road signs recognized by the forward recognition camera.

·

The RSA system can be turned on and off through the settings tab.


Buzzer Sounds when the speed limit is exceeded*1, a no overtaking notification is displayed*2 or there is an entry prohibition notifications*2.
Steering Pad Switch Assembly Meter Control Switch Sends a multi-information operating signal to the forward recognition camera.
Airbag Sensor Assembly Yawrate Sensor Detects the yaw rate and sends it to the forward recognition camera.
Spiral Cable with Sensor Sub-assembly Steering Sensor Detects the angle and direction of steering and transmits signals to the forward recognition camera.
Headlight Dimmer Switch Assembly Sends a turn signal command to the combination meter assembly.
Main Body ECU (Multiplex Network Body ECU)
·

Sends the wiper operation signal to the forward recognition camera.

·

Sends country specification information signals to the forward recognition camera.


Navigation ECU*3
·

Sends map information to the radio and display receiver assembly.

·

Performs coordinated control with the forward recognition camera in regards to speed limit information.


Radio and Display Receiver Assembly*3 Sends map information from the navigation ECU to the forward recognition camera.
Network Gateway ECU Relays and transmits each CAN communication data signal.
Air Conditioning Amplifier Assembly Sends the outside temperature signal to the forward recognition camera.



FUNCTION


a.

The RSA system recognizes the following traffic signals using the forward recognition camera.

Models for Europe
Category Sign Type Example of Recognizable Sign
Speed Limit Round Maximum Speed Limit/End of Speed Limit
Y180848

No Overtaking No Overtaking/End of No Overtaking
Y205955

Supplemental Signs Road Condition Signs Ramp Way
Y180850

Rain
Y180851

Wet
Y224423

Ice
Y180852

Time
Y235976

End of Prohibition
Y180854


*: Models with navigation system

Information Signs Related Speed Limit Highway Sign (Entrance, Exit)
Y235941

Motorway Sign (Entrance, Exit)
Y235942

Urban Area Sign (Start, End)
Y235943

Y235975

Residential Area Sign (Start, End)
Y235944

No Entry*
Y236045

Stop
Y233205


Except Models for Europe
Category Sign Type Example of Recognizable Sign
Speed Limit Round Maximum Speed Limit
Y235974

Supplemental Sign School Zone
Y251539



b.

The RSA system displays the following traffic signals using the forward recognition camera.

Models for Europe
Category Display Example Details
Speed Limit Related
Y180848

·

Informs the driver of the maximum speed limit of the currently driven road.

·

The displayed sign reflects the speed limit on the recognized sign.


Speed Limit Related
Y235941

Informs the driver highway sign (entrance, exit).
Y235942

Informs the driver motorway sign (entrance, exit).
Y235943

Y235975

Informs the driver urban area sign (start, end).
Y235944

Informs the driver residential area sign (start, end).
No Overtaking Related
Y205955

Informs the driver when they are in a no overtaking zone on the currently driven road.
No Entry*
Y236045

Informs the driver that there are vehicle entry restricted sections on the currently driven road.
All Canceled (All restrictions canceled. Return to default road regulations.)
Y180854

Informs the driver when all applicable prohibitions, such as speed limit and no overtaking, have ended.
Stop
Y233205

Informs the driver that there is a stop ahead.

*: Models with navigation system

Speed Limit with Supplemental Sign Related Ramp Way
Y180858

Informs the driver of the ramp way direction. However, this item is not displayed when making a lane change without operating the turn signal light.
Rain
Y235940

Informs the driver of the maximum speed limit on the currently driven road when it is raining or the road surface is wet.
Ice
Y180860

Informs the driver of the maximum speed limit on the currently driven road when there is accumulated snow or ice.
Time
Y235977

Informs the driver when of the time zone speed limit sign on the currently driven road.
Blank
Y180853

The display is blank when the system is unable to recognize a supplemental sign.

Except Models for Europe
Category Display Example Details
Speed Limit Related
Y235974

·

Informs the driver of the maximum speed limit of the currently driven road.

·

The displayed sign reflects the speed limit on the recognized sign.


Conditional Speed Limit Sign School Zone
Y260234

Informs the driver that the currently driven road is in a school zone and its speed limit changes depending on the time of day.

HINT:

A non-official (sign not meeting Vienna Convention) or a recently introduced traffic sign may not be recognized.



c.

Notification functions are used in the RSA system which invert the colors of displayed signs, flash signs, etc. to notify the driver.

i.

Speed Limit Exceeded Notification

·

While a speed limit sign is displayed, if the actual vehicle speed exceeds the speed limit plus a designated threshold*1, the colors of the displayed sign are inverted and the buzzer sounds.*2 For example, if the threshold is set to 5 km/h (3 mph) and the speed limit sign is 60 km/h (37 mph), the colors of the displayed sign are inverted and the buzzer sounds, when the actual vehicle speed exceeds 65 km/h (40 mph). Furthermore, the system also inverts a speed limit sign with supplemental sign in the same way. However, the system does not invert the colors of the supplemental sign.

HINT:

*1: The threshold can be adjusted to 1 of 3 levels through the customization function.

*2: Customization is required for inverted display and sounding of the buzzer.



Notification Method Display Example
Inverted Display
Y180861



ii.

No Overtaking Notification (Models for Europe)

·

While a no overtaking sign is displayed, if the system detects that the vehicle is attempting to overtake another vehicle, the system flashes the displayed sign and sounds the meter buzzer.*

HINT:

*: Customization is required for blinking display and sounding of the meter buzzer.



Notification Method Display Example
Flashing Display
Y205956



iii.

No-entry Notification (Models with Navigation System)

·

While a no entry sign is recognized, if the system detects that the driver is driving on a road where entry is prohibited, based on map information, the system flashes the displayed sign and sounds the meter buzzer.*

HINT:

*: Customization is required for blinking display and sounding of the meter buzzer.



Notification Method Display Example
Flashing Display
Y187317




d.

The RSA system can be turned on or off through the settings tab of the multi-information display.


e.

A customization function is used for the RSA, which allows settings such as the notification method and level for exceeding the speed limit to be changed. Setting changes are made through the customization tab of the multi-information display. Refer to the Repair Manual for details.



SYSTEM CONTROL


a.

RSA Control Pattern 1

i.

After a road sign* other than a stop sign is recognized by the forward recognition camera, the sign is displayed on the multi-information display.

*: Except for stop sign


ii.

While a sign is displayed on the multi-information display, if no sign has been recognized within a specified distance, display of the current sign is turned off.

Y260083E01
2.313,0.813 2.479,0.813 2.479,0.813 2.719,1.344 true 1.635,0.708 2.406,0.979 0.771,0.271 10 false Road Sign 3.875,0.698 5.521,0.948 1.646,0.25 10 false Specified Distance Driven 0.875,2.656 2.375,2.906 1.5,0.25 10 false : Sign display off 0.875,3.198 2.375,3.448 1.5,0.25 10 false : Sign display on



b.

RSA Control Pattern 2 (Models for Europe)

i.

After a stop sign is recognized by the forward recognition camera, the sign is displayed on the multi-information display.


ii.

While a sign is displayed on the multi-information display, display of the sign is turned off when the vehicle passes the road sign.

Y244471E02
4.448,1.521 4.635,2.385 4.635,2.385 4.865,2.385 true 4.927,2.25 6.406,2.625 1.479,0.375 10 false Road Sign Recognized 1.042,3.115 2.521,3.49 1.479,0.375 10 false : Sign Display On 1.021,2.531 2.5,2.906 1.479,0.375 10 false : Sign Display Off



c.

RSA Control Pattern 3

i.

When the ignition switch is turned off while a speed limit sign is displayed on the multi-information display, the same sign is displayed when the ignition switch is turned ON (IG) again.

Y260084E01
1.167,2.99 3.771,3.188 2.604,0.198 10 false : Sign display on 0.917,0.438 2.865,0.667 1.948,0.229 10 false Ignition switch is turned off. 4.688,0.427 6.844,0.667 2.156,0.24 10 false Ignition switch is turned ON (IG).



d.

RSA Control Pattern 4

i.

While a sign is displayed on the multi-information display, the sign is turned off when turning left or right onto a new road.

Y260085E01
5.708,3.958 7.115,4.448 1.406,0.49 10 false Road Sign Recognized 0.833,4.281 2.292,4.531 1.458,0.25 10 false : Sign display off 0.844,5.042 2.302,5.292 1.458,0.25 10 false : Sign display on




DIAGNOSIS


a.

In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the GTS. For details, refer to the Repair Manual.