FUNCTION OF MAIN COMPONENTS
The main components in the dynamic radar cruise control system have the following functions:
| Component | Function | |
|---|---|---|
|
*: Models with dynamic radar cruise control with road sign assist |
||
| Millimeter Wave Radar Sensor Assembly | ·
Radiates millimeter radar waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance and the relative speed. ·
While the system is in vehicle-to-vehicle distance control mode, the millimeter wave radar sensor assembly detects the vehicle ahead based on signals from the millimeter wave radar sensor assembly and forward recognition camera. Then, the millimeter wave radar sensor assembly calculates the acceleration or deceleration rate required in order to attain the target vehicle-to-vehicle distance, and outputs a request signal to the ECM. ·
If the system detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs). |
|
| Forward Recognition Camera | ·
Detects lane markers and objects on the road ahead using the image captured by the camera sensor. ·
Controls the supply of electric current to the forward recognition hood when the ambient temperature is low. |
|
| Forward Recognition Hood | Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up. | |
| Cruise Control Main Switch | ON-OFF Button | ·
Turns the cruise control system on and off. ·
Vehicle to vehicle distance control mode becomes activated immediately after the main switch is turned on. The mode shifts to constant speed control mode by pressing and holding the button more than 1.5 sec from the cruise control system off. |
| CANCEL Switch | A cancel signal is output to the ECM when this switch is operated. | |
| +RES Switch | ·
The acceleration function and resuming of a preset speed can be performed by operating this switch. A signal is output to the ECM when this switch is operated. ·
The dynamic radar cruise control with road sign assist operation signals are sent to the ECM.* |
|
| -SET Switch | ·
The deceleration function and vehicle speed setting resume signals are output to the ECM when this switch is operated. ·
The dynamic radar cruise control with road sign assist operation signals are sent to the ECM.* |
|
| Steering Pad Switch Assembly | Vehicle-to-vehicle Distance Control Switch | While the system is in vehicle-to-vehicle distance control mode, the driver can operate the vehicle-to-vehicle distance control switch to select the vehicle-to-vehicle distance in three levels: long, middle and short. |
| Combination Meter Assembly | Cruise Control Indicator | ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly illuminates the cruise control indicator (constant speed control mode) or cruise control indicator (vehicle-to-vehicle distance control mode) when the cruise control system has been turned on using the cruise control main switch. ·
Based on a cruise control indicator operation signal sent by the ECM, the combination meter assembly turns off the cruise control indicator if a malfunction occurs in the cruise control system. |
| Cruise SET Indicator | Illuminates when the vehicle speed is set. | |
| Multi-information Display | ·
Displays a warning message to alert the driver in accordance with a signal provided by the ECM. ·
During dynamic radar cruise control operation, the multi-information display receives signals from the ECM in order to display the system conditions. |
|
| Buzzer | ·
Sounds a buzzer when it receives a signal from the ECM to alert the driver that the distance between vehicles is short. ·
If the ECM detects automatic cancel or warning signals while the vehicle is operating under cruise control, this buzzer sounds to inform the driver. |
|
| Headlight Dimmer Switch Assembly | Sends a turn signal command to the combination meter assembly. | |
| Spiral Cable with Sensor Sub-assembly | Steering Sensor | Detects the angle and direction of steering and transmits signals to the skid control ECU and ECM. |
| Airbag Sensor Assembly | Yawrate Sensor | Detects the yaw rate of the vehicle and transmits signals to the ECM. |
| Stop Light Switch Assembly | Detects brake pedal depression and transmits its signal to the ECM. | |
| Brake Actuator Assembly | Skid Control ECU | ·
While the system is operating in vehicle-to-vehicle distance control mode, the skid control ECU operates the brake actuator in accordance with the brake request signal received from ECM. ·
Applies the brakes in accordance with signals from the ECM. ·
During stop retention control, when this ECU detects that the vehicle is parked through a driver side courtesy light switch signal or driver side seat belt buckle switch signal, or an electric parking brake switch assembly signal is input, the ECU operates the parking brake, then the system control is canceled. |
| ECM | ·
Controls the dynamic radar cruise control system in accordance with signals from switches, sensors. ·
If the ECM detects a malfunction in the dynamic radar cruise control system, it will store Diagnostic Trouble Codes (DTCs). |
|
| Throttle Body with Motor Assembly | Throttle Control Motor | Adjusts the throttle valve opening angle in accordance with signals from the ECM. |
| Throttle Position Sensor | Detects the throttle valve opening angle and outputs it to the ECM. | |
| Park/Neutral Position Switch Assembly | Detects the shift lever position. | |
| Shift Lock Control Unit Assembly | Transmission Control Switch | ·
Detects the shift lever position and transmits signals to the transmission control ECU. ·
Informs the transmission control ECU of driver upshift or downshift operations while the shift lever is in M. |
| Accelerator Pedal Sensor Assembly | Detects the accelerator pedal depression angle and transmits it to the ECM. | |
| Electric Parking Brake Switch Assembly | Electric Parking Brake Switch | Outputs a parking brake application signal to the parking brake ECU (skid control ECU) |
| VSC OFF (TRC OFF) Switch | Detects the VSC OFF (TRC OFF) signals and outputs it to the skid control ECU. | |
| Parking Brake Actuator Assembly | Operates the parking brake actuator according to signals from the parking brake ECU (skid control ECU). | |
| Pre-collision City Buzzer | Sounds a buzzer when it receives a signal from the forward recognition camera to alert the driver that the distance between vehicles is short. | |
| Network Gateway ECU | Relays and transmits each CAN communication data signal. | |
FUNCTION
Function List
The control of the dynamic radar cruise control system varies depending on the mode:
A: Constant Speed Control Mode
B: Vehicle-to-vehicle Distance Control Mode
| Function | Outline | Mode | |
|---|---|---|---|
| A | B | ||
|
○: Available -: Not Available |
|||
| Constant Speed Control | The ECM compares the actual vehicle speed and the set speed and if the vehicle speed is lower than the set speed, it uses the throttle control motor to increase the throttle valve opening angle. | ○ | ○ |
| Deceleration Control | Performs throttle control and brake control in order to decelerate the vehicle so that the vehicle-to-vehicle distance between the driver's own vehicle and the vehicle ahead equals the set distance. | - | ○ |
| Follow-up Control | After performing deceleration control, the driver's own vehicle follows the vehicle ahead in order to maintain the proper vehicle-to-vehicle distance in accordance with the vehicle speed. | - | ○ |
| Acceleration Control | Accelerates the vehicle in order to attain the set vehicle speed if the vehicle ahead or the driver's own vehicle has changed lanes. | - | ○ |
| Stop Control | Detects if the vehicle ahead has stopped, performs motive force control and stops the vehicle while maintaining proper vehicle-to-vehicle distance. | - | ○ |
| Stop Retention Control | Judges if the vehicle is stopped, performs brake control and keeps the vehicle stopped through the brake hold function. | - | ○ |
| Start Control | Detects that the vehicle ahead starts moving again, displays the message on the multi-information display to urge the driver to perform the start-off operation (to operate the +RES switch on the cruise control main switch or depress the accelerator pedal), and resumes follow-up control after the vehicle is started. | - | ○ |
| Turn Signal-linked Control | If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed. | - | ○ |
| Dynamic Radar Cruise Control with Road Sign Assist | This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit. | - | ○ |
| Set Control | When the following conditions are met, and the cruise control main switch is pressed to the -/SET side and released, the ECM stores the vehicle speed and maintains the vehicle constantly at the current speed.
·
The ON-OFF button on the cruise control main switch is pressed. |
○ | ○ |
| The vehicle is being driven at a speed of approximately 30 km/h (20 mph) or more. | ○ | - | |
| The vehicle is traveling at a speed within the range of approximately 30 km/h (20 mph) or more. | - | ○ | |
| Low Speed Limit Control | The low speed limit is the lowest speed that cruise control can be set at and it is designed to be approximately 25 km/h (16 mph). The cruise control cannot be set below that speed. If the vehicle speed drops below that speed while driving using cruise control, the cruise control will be canceled automatically. The set vehicle speed is kept in memory. | ○ | ○ |
| Coast Control | While the cruise control main switch is held to the SET/- side, the vehicle speed and the set vehicle speed change as follows, according to the mode: | ○ | ○ |
·
The vehicle decelerates constantly. ·
The set vehicle speed changes to the speed at which the -SET switch is released. |
○ | - | |
·
The set vehicle speed decreases in increments of 5 km/h or 5 mph. [Example: 103 → 100 → 95 → 90 → 85 km/h (mph)] ·
The vehicle decelerates rapidly. The vehicle will remain at the speed that the vehicle is traveling at when the -SET switch is released. |
- | ○ | |
| Tap Down Control | When the cruise control main switch is moved momentarily (approximately 0.6 seconds or less) to the -SET side, the vehicle speed and the set vehicle speed change as follows, according to the mode: | ○ | ○ |
·
The vehicle will decelerate in increments of approximately 1 km/h or 1 mph each time the -SET switch is pushed. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will change to the speed at which the vehicle was being driven at the time the -SET switch was operated. |
○ | - | |
| The vehicle will decelerate in increments of approximately 1 km/h or 1 mph for each time the -SET switch is pushed. | - | ○ | |
| Accelerator Control | While the cruise control main switch is held to the +RES side, the vehicle speed and the set vehicle speed change as follows, according to the mode: | ○ | ○ |
·
The vehicle will accelerate constantly. ·
The set vehicle speed changes to the speed at which the +RES switch is released. |
○ | - | |
·
The set vehicle speed increases in increments of 5 km/h or 5 mph. [Example: 83 → 85 → 90 → 95 → 100 km/h (mph)] ·
The vehicle will accelerate to the speed that is set at the time the +RES switch is released. However, only the set vehicle speed will change during follow-up control. |
- | ○ | |
| Resume Control | If the vehicle speed is above the low speed limit, the +RES switch can be pushed to resume cruise control operation and reach the vehicle speed that was set at the time the driver canceled cruise control. | ○ | ○ |
| Even if the vehicle speed drops below the low speed limit, resumption can be performed when the vehicle speed increases to above the low speed limit. However, resumption can be performed even if the vehicle speed is below the low speed limit when the vehicle is running in mode B and there is a vehicle ahead. | - | ○ | |
| If the vehicle ahead changes driving lanes during follow-up control, the vehicle speed is gradually increased to the set vehicle speed. At this time, the vehicle speed can be increased promptly by pushing the +RES switch. | - | ○ | |
| After the vehicle ahead has started running again under stop retention control and then the message that urges the driver to perform the start-off operation has been displayed, when the cruise control main switch is pushed to the +RES side, follow-up control is resumed and the vehicle can be accelerated up to the set speed. | - | ○ | |
| Tap Up Control | When the cruise control main switch is moved momentarily (approximately 0.6 seconds or less) to the +RES side, the vehicle speed and the set vehicle speed change as follows: | ○ | ○ |
·
The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch was pushed. ·
However, if the difference between the actual vehicle speed and the set vehicle speed is greater than 5 km/h (3 mph), the set vehicle speed will not change. |
○ | - | |
| The vehicle will accelerate in increments of approximately 1 km/h or 1 mph for each time the +RES switch is pushed. | - | ○ | |
| Manual Cancel Control | If any of the following signals are sent to the ECM, the cruise control is canceled accordingly:
·
Stop light switch on signal (The brake pedal is depressed). ·
Shift lever is moved from D to any other position. ·
CANCEL switch on signal (cruise control main switch is moved to CANCEL side). ·
Electric parking brake is applied. |
○ | ○ |
| Automatic Cancel Control | When an automatic cancel signal is sent to the ECM, cruise control operation is canceled. At this time, the type of warning sent to the driver and the control resumption condition varies according to the cancel signal. | ○ | ○ |
| Mode Switching Control | The following operations switch modes:
·
Vehicle-to-vehicle distance control mode is activated immediately after the switch is turned on. The mode is changed to constant speed control mode by pressing and holding the switch for more than 1.5 seconds while the dynamic radar cruise control system is turned off. |
○ | ○ |
| Other Cancel Conditions | ·
VSC operates during cruise control driving. ·
TRC operates for a certain period of time while the cruise control. ·
TRC is off or VSC is off. ·
Ignition switch off. ·
PCS operates during cruise control driving. ·
Electric parking brake operates during cruise control driving. ·
DSC operates during cruise control driving (Only during vehicle-to-vehicle distance control mode). |
○ | ○ |
| Diagnosis | If a malfunction occurs in the dynamic radar cruise control system during cruise control operation, the ECM cancels cruise control and memorizes information related to the malfunction. | ○ | ○ |
Constant Speed Control Mode
The ECM compares the set vehicle speed and the actual vehicle speed, and performs constant speed control in order to attain the set vehicle speed.
Vehicle-to-vehicle Distance Control Mode
In vehicle-to-vehicle distance control mode, the ECM performs constant speed control function, deceleration control function, follow-up control function, acceleration control function, stop control function, stop retention control function, start control function or turn signal-linked control function based on the information about the vehicle ahead transmitted from the millimeter wave radar sensor assembly and forward recognition camera.
Constant Speed Control Function
The ECM compares the set vehicle speed and the actual vehicle speed, and performs constant speed control by regulating the throttle in order to attain the set vehicle speed. The millimeter wave radar sensor assembly uses the millimeter radar wave signal and information from the forward recognition camera to determine the condition in front of the vehicle and sends acceleration/deceleration requests to the ECM.
Deceleration Control Function
The millimeter wave radar sensor assembly calculates the target deceleration rate in accordance with signals from the millimeter wave radar sensor assembly and forward recognition camera and transmits a deceleration request signal to the ECM. Upon receiving this signal, the ECM closes the throttle valve in order to cause the vehicle to decelerate.
This control is not performed in the presence of a parked vehicle or object or below the settable vehicle speed range.
If the millimeter wave radar sensor assembly determines that further deceleration is necessary, it transmits a brake request signal to the ECM. Upon receiving this signal, the ECM transmits a brake request signal to the skid control ECU. The skid control ECU then controls the brake actuator to apply the brakes.
At this time, if the deceleration rate is higher than a predetermined value, the skid control ECU outputs a stop light illumination request signal to the stop lights in order to warn any vehicles behind.
If the vehicle is not decelerating adequately, ECM sounds a buzzer. The buzzer is sounded to urge the driver to depress the brake pedal.
Follow-up Control Function
After performing deceleration control, the millimeter wave radar sensor assembly transmits a request signal to the ECM so that the vehicle can follow the vehicle ahead while maintaining the proper vehicle-to-vehicle distance according to the vehicle speed. Upon receiving this signal, the ECM regulates the throttle in order to perform follow-up control.
3 stages (long, middle and short) of vehicle-to-vehicle distance can be selected by operating the vehicle-to-vehicle distance control switch.
Acceleration Control Function
If the millimeter wave radar sensor assembly detects (based on the millimeter wave radar sensor assembly and forward recognition camera) that either the vehicle ahead or the driver has changed lanes, an acceleration request signal is transmitted to the ECM in order to attain the set vehicle speed. Upon receiving this signal, the ECM regulates the throttle in order to perform acceleration control.
Stop Control Function
During vehicle-to-vehicle distance control mode, if the vehicle ahead stops, the millimeter wave radar sensor assembly maintains an appropriate vehicle-to-vehicle distance while at the same time calculating the necessary driving force to stop the vehicle, and sends a drive request signal to the ECM and skid control ECU. When the ECM and skid control ECU receive this signal, they control the driving force and stop the vehicle.
At this time, the skid control ECU outputs a stop light illumination request signal in order to inform anyone who might be following the vehicle.
The distance between the driver's own vehicle and the preceding vehicle when the vehicles are stopped is set to approximately 3 m to 5 m (10 ft. to 16 ft.) regardless of the vehicle-to-vehicle distance preset by using the distance control switch.
Stop Retention Control Function
After the vehicle has stopped under stop control, the ECM transmits a stop retention request signal to the skid control ECU. Upon receiving this signal, the skid control ECU activates the brake hold function and keeps the vehicle stopped.
If the vehicle ahead starts off within approximately 3 seconds after own vehicle stops, follow-up cruising will be resumed.
Start Control Function
When the millimeter wave radar sensor assembly detects that the vehicle ahead starts moving again from the millimeter wave radar sensor assembly and forward recognition camera signal, it displays the messages on the multi-information display to urge the driver to perform the start-off operation (to push the +RES switch or depress the accelerator pedal).
Upon receiving the start-off operation signal generated by pushing the +RES switch on the cruise control main switch or by depressing the accelerator pedal, the millimeter wave radar sensor assembly transmits a motive force request signal to the ECM. Upon receiving this signal, the ECM controls the motive force, starts the vehicle and resumes follow-up control.
Pressing the +RES switch while the vehicle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pressed.
Turn Signal-linked Control Function
If the turn signal switch is operated when changing lanes to the passing lane at a vehicle speed of approximately 80 km/h (50 mph) during follow-up control, the vehicle will begin preliminary acceleration; once the vehicle has changed lanes it will first maintain this preliminary acceleration, and then slowly accelerate to the set vehicle speed.
Dynamic Radar Cruise Control with Road Sign Assist (Models with Dynamic Radar Cruise Control with Road Sign Assist)
This function is turned on and while RSA system speed limit information is displayed, the speed limit can be set by holding down the +RES switch to increase the set vehicle speed to the speed limit, or by holding down the -SET switch to reduce the set vehicle speed to the speed limit.
Automatic Cancel Control
If one of the conditions listed below occurs while the vehicle is being driven using cruise control, speed control by the cruise control system will be canceled. Then, the following warning items will appear for the driver.
| Situation | Warning | |
|---|---|---|
| Multi-information Display | Buzzer | |
| If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·
An open or short circuit in the stop light switch assembly. Speed control by the cruise control system is disabled until the ignition switch is turned off. |
Cruise Control
Malfunction Visit Your Dealer |
Sounds |
| If any of the following conditions occurs, the ECM cancels the cruise control.
·
Stop light switch assembly input signal is abnormal. ·
Cancel circuit malfunction. ·
Brake control system malfunction. ·
Communication malfunction between the skid control ECU and ECM. Speed control by the cruise control system is disabled until the ignition switch is turned off. |
Cruise Control
Malfunction Visit Your Dealer |
Sounds |
| If the following condition occurs, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.
·
The vehicle speed drops below the low speed limit [approximately 30 km/h (20 mph)]. |
- | - |
| If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·
The vehicle speed drops more than 16 km/h (10 mph) below the set vehicle speed. |
- | - |
| If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·
Malfunction in engine control system. Speed control by the cruise control system is disabled until the ignition switch is turned off and the cruise control switch is turned on again. |
- | - |
| If any of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
VSC operates during cruise control driving. ·
TRC operates for a certain period of time during cruise control driving. ·
TRC is off or VSC is off. ·
PCS operates during cruise control driving. ·
Electric parking brake operates during cruise control driving. |
- | - |
| Situation | Warning | |
|---|---|---|
| Multi-information Display | Buzzer | |
| If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·
An open or short circuit in the stop light switch assembly. Speed control by the cruise control system is disabled until the ignition switch is turned off. |
Cruise Control
Malfunction Visit Your Dealer |
Sounds |
| If one of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·
Malfunction of the millimeter wave radar sensor assembly. ·
Misalignment of the axis of the millimeter wave radar sensor assembly. ·
Malfunction in the dynamic radar cruise control system other than those given above. ·
Stop light switch assembly input signal is abnormal. ·
Cancel circuit malfunction. ·
The brake holding control system has a malfunction. Speed control by the cruise control system is disabled until the ignition switch is turned off. |
Cruise Control
Malfunction Visit Your Dealer |
Sounds |
| If the following condition occurs, the ECM clears the set vehicle speed and cancels the cruise control.
·
Malfunction in engine control system. Speed control by the cruise control system is disabled until the ignition switch is turned off. |
- | - |
| If the following condition occurs, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.
·
The millimeter wave radar sensor assembly or the emblem are dirty. Speed control by the cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly. |
Radar Cruise
Control Unavailable See Owner's Manual |
Sounds |
| If any of the following conditions occurs, the ECM cancels the cruise control while retaining the set vehicle speed in its memory.
·
The measurement becomes extremely unstable due to poor weather conditions. ·
Brake control by the dynamic radar cruise control system is temporarily unavailable. ·
The beam axis of the millimeter wave radar sensor assembly is being aligned. ·
A malfunction in the forward recognition camera. ·
Forward recognition camera temporarily not available. Speed control by the cruise control system is prohibited until the condition is corrected or the cruise control system is turned off and back on again using the cruise control switch on the steering pad switch assembly. |
Radar Cruise
Control Unavailable |
Sounds |
| If the following condition occurs, the ECM cancels the cruise control while retaining the setting vehicle speed in its memory.
·
The vehicle speed drops below the low speed limit [approximately 25 km/h (16 mph)]. |
- | Sounds
Twice |
| If any of the conditions listed below occurs, the ECM clears the set vehicle speed and cancels speed control by the cruise control system.
·
VSC operates during cruise control driving. ·
TRC operates for a certain period of time during cruise control driving. ·
TRC is off or VSC is off. ·
PCS operates during cruise control driving. ·
DSC or electric parking brake operates during cruise control driving. |
- | - |
| If any of the following conditions occur while the vehicle is stopped, the ECM cancels control of vehicle speed by the dynamic radar cruise control system.
·
The driver seat belt is unfastened. ·
The driver door is opened. ·
The vehicle is parked for a long period of time. ·
The vehicle is driving on a steep hill. |
Radar Cruise
Control Unavailable Press Brake to Resume Driving |
- |
| If any of the conditions listed below occurs while the vehicle is stopped, the ECM cancels speed control by the cruise control system while retaining the set vehicle speed in its memory.
·
Stop light switch assembly input signal is abnormal. ·
Malfunction in the millimeter wave radar sensor assembly. ·
Beam axis of millimeter wave radar sensor assembly misaligned. ·
The electric parking brake system is malfunctioning. ·
An open or short circuit in the stop light switch. ·
Problem with cruise control switch cancel circuit. ·
Millimeter wave radar sensor assembly becomes dirty. ·
Brake control by the dynamic radar cruise control system is temporarily unavailable. ·
The forward recognition camera is temporarily unavailable. |
Cruise Control
Fault Press Brake to Deactivate Visit Your Dealer |
Sounds |
DIAGNOSIS
In order to make system inspections easier to perform, a diagnosis function is used in consideration of serviceability. The DTCs of malfunctioning parts can be read by connecting the GTS. For details, refer to the Repair Manual.