Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P050031  Vehicle Speed Sensor "A" No Signal  


DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the brake actuator assembly (skid control ECU) and wheel speed sensor. The wheel speed sensor monitors the wheel rotation speed and sends a signal to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.



A283589E13
2.74,0.625 3.333,0.833 0.594,0.208 10 false 4-Pulse 4.708,0.615 5.25,0.833 0.542,0.219 10 false 4-Pulse 5.771,1.854 6.188,2.104 0.417,0.25 10 false ECM 3.094,1.875 4.99,2.25 1.896,0.375 10 false Combination Meter Assembly 1.229,1.875 2.844,2.427 1.615,0.552 10 false Brake Actuator Assembly (Skid Control ECU) 0.229,1.198 1.125,1.583 0.896,0.385 10 false from Wheel Speed Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P050031 Vehicle Speed Sensor "A" No Signal While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

Brake actuator assembly (Skid control ECU)

·

ECM


Comes on DTC stored SAE Code:
P0500

MONITOR DESCRIPTION

for CVT:

The ECM assumes that the vehicle is being driven when the vehicle speed sensor signal is being transmitted by the combination meter. If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores this DTC.


for Manual Transaxle:

The ECM assumes that the vehicle is being driven when the fuel cut operation* is being executed. If there is no speed signal, despite the conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

*: Idle fuel cut is executed when the throttle valve is fully closed and engine speed is over 2800 rpm.


MONITOR STRATEGY

Required Sensors/Components (Main) Vehicle speed sensor
Combination meter assembly
Brake actuator assembly (Skid control ECU)
Required Sensors/Components (Related) Park/Neutral position switch*
Engine coolant temperature sensor
Crankshaft position sensor
Throttle position sensor
Mass air flow meter
Frequency of Operation Continuous

*: for CVT


TYPICAL ENABLING CONDITIONS

for CVT
Engine Running

for Manual Transaxle
Fuel cut On

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No signal

CONFIRMATION DRIVING PATTERN

for CVT:

A232052E36
0.729,0.865 2.208,1.26 1.479,0.396 10 false 24 km/h (15 mph) 1.417,2 1.938,2.229 0.521,0.229 10 false Idling 0.677,2.385 2.146,2.771 1.469,0.385 10 false Ignition Switch ON 2.385,2.219 2.615,2.385 0.229,0.167 10 false [A] 4.708,0.417 4.917,0.583 0.208,0.167 10 false [B] 6.25,3.229 6.448,3.427 0.198,0.198 10 false [C] 4.063,3.104 5.76,3.375 1.698,0.271 10 false Total of 30 seconds or more 0.969,0.25 2.281,0.542 1.313,0.292 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Start the engine.

9.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Stop the vehicle.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P050031.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




for Manual Transaxle:

A240416E35
6.083,2.948 5.906,3.531 5.906,3.531 5.531,3.531 false 0.708,0.875 2.052,1.271 1.344,0.396 10 false 24 km/h (15 mph) 1.417,2.052 1.813,2.219 0.396,0.167 10 false Idling 0.594,2.396 1.771,2.583 1.177,0.188 10 false Ignition Switch ON 2.385,2.271 2.615,2.438 0.229,0.167 10 false [A] 4.708,0.469 4.917,0.635 0.208,0.167 10 false [B] 6.25,3.292 6.448,3.49 0.198,0.198 10 false [D] 6.063,1.125 6.26,1.323 0.198,0.198 10 false [C] 4.01,3.052 5.823,3.313 1.813,0.26 10 false Total of 30 seconds or more 4.323,3.448 5.51,3.594 1.188,0.146 10 false 5 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine.

7.

Turn the GTS on [A].

8.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel cut [C].

10.

Stop the vehicle.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P050031.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A309967E11
0.333,1.021 1.594,1.583 1.26,0.563 10 false from Brake Actuator Assembly (Skid Control ECU) 2.563,0.979 2.823,1.198 0.26,0.219 10 false 5 4.26,0.979 4.521,1.198 0.26,0.219 10 false 6 2.771,0.979 3.031,1.198 0.26,0.219 10 false SI 3.99,0.979 4.25,1.198 0.26,0.219 10 false +S 2.563,1.865 2.823,2.083 0.26,0.219 10 false F4 2.563,2.021 4.552,2.271 1.99,0.25 10 false Combination Meter Assembly 5.333,0.99 5.594,1.208 0.26,0.219 10 false 44 5.563,0.99 6.24,1.281 0.677,0.292 10 false SPD 6.063,1.896 6.417,2.146 0.354,0.25 10 false A38 6.052,2.052 6.406,2.302 0.354,0.25 10 false ECM 5.125,2.99 6.146,3.198 1.021,0.208 10 false to Other ECUs

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 372 212

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B




A

2.CHECK COMBINATION METER SYSTEM (SPEED SIGNAL CIRCUIT)

B

2.CHECK COMBINATION METER SYSTEM (SPEED SIGNAL CIRCUIT)
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372
HINT:

If no DTCs (no pending DTCs) are output to the GTS, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END