Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0290846 STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY G

STOP AND START  STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY  INSPECTION  


PROCEDURE

Hide 84390B 1.INSPECT ECO RUN CANCEL SWITCH ASSEMBLY (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for LHD)

a.

Check the resistance.

i.
A387514C01
2.583,1.667 2.24,1.385 true 1.333,1.75 1.719,1.375 true 0.083,0.083 0.313,0.333 0.229,0.25 10 false *a 1.188,1.719 1.344,1.917 0.156,0.198 10 false S 2.635,1.625 2.792,1.823 0.156,0.198 10 false E
*a Component without harness connected
(Eco Run Cancel Switch Assembly (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
11 (S) - 8 (E) Pushed Below 1 Ω
Not pushed 10 kΩ or higher


If the result is not as specified, replace the eco run cancel switch assembly (electric parking brake switch assembly).



b.

Check illumination.

i.
A387514C02
1.135,1.021 0.667,0.833 true 2.292,1.042 2.75,0.833 true 0.083,0.083 0.313,0.271 0.229,0.188 10 false *a 0.354,0.688 0.75,0.896 0.396,0.208 10 false ILL+ 2.802,0.719 3.198,0.927 0.396,0.208 10 false ILL-
*a Component without harness connected
(Eco Run Cancel Switch Assembly (Electric Parking Brake Switch Assembly))


Apply battery voltage between the terminals of the switch, and check the illumination condition of the eco run cancel switch assembly (electric parking brake switch assembly).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the eco run cancel switch assembly (electric parking brake switch assembly).



Hide 84390B 2.INSPECT ECO RUN CANCEL SWITCH ASSEMBLY (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for RHD)

a.

Check the resistance.

i.
A387514C03
2.396,1.76 2.24,1.375 true 1.146,1.781 1.344,1.396 true 0.083,0.083 0.313,0.333 0.229,0.25 10 false *a 1.083,1.802 1.24,2 0.156,0.198 10 false S 2.385,1.792 2.542,1.99 0.156,0.198 10 false E
*a Component without harness connected
(Eco Run Cancel Switch Assembly (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
13 (S) - 8 (E) Pushed Below 1 Ω
Not pushed 10 kΩ or higher


If the result is not as specified, replace the eco run cancel switch assembly (electric parking brake switch assembly).



b.

Check illumination.

i.
A387514C02
1.135,1.021 0.667,0.833 true 2.292,1.042 2.75,0.833 true 0.083,0.083 0.313,0.271 0.229,0.188 10 false *a 0.354,0.688 0.75,0.896 0.396,0.208 10 false ILL+ 2.802,0.719 3.198,0.927 0.396,0.208 10 false ILL-
*a Component without harness connected
(Eco Run Cancel Switch Assembly (Electric Parking Brake Switch Assembly))


Apply battery voltage between the terminals of the switch, and check the illumination condition of the eco run cancel switch assembly (electric parking brake switch assembly).

OK:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the eco run cancel switch assembly (electric parking brake switch assembly).