Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2016.10–2019.09
RM32H0E _53 Suspension _059519 FRONT SUSPENSION _0291583 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front shock absorber assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

SST used when removing/installing the coil spring are shown as follows.

C428017C03
0.677,1.24 6.115,3.719 5.438,2.479 1.313,0.542 1.313,0.188 1.313,0.188 3.563,0.188 true 2.396,0.542 2.396,0.198 true 4.167,1.646 4.594,1.646 true 5.323,0.458 5.323,0.167 true 4.292,0.448 4.292,0.177 4.292,0.177 6.542,0.177 true 6.115,2.427 6.531,2.427 true 3.625,0.083 3.938,0.281 0.313,0.198 10 false *1 6.604,2.333 6.917,2.531 0.313,0.198 10 false *4 4.677,1.552 4.99,1.75 0.313,0.198 10 false *3 6.604,0.083 6.917,0.281 0.313,0.198 10 false *2
*1 SST (09727-58100) *2 SST (09727-58140)
*3 SST (09727-58030) *4 SST (09727-58010)




PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 3.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

a.

for LHD:

i.
C365622

Disengage the claw and remove the No. 1 heater air duct splash shield seal from the outer cowl top panel sub-assembly.



b.

for RHD:

i.
C365623

Disengage the claw and remove the No. 1 heater air duct splash shield seal from the outer cowl top panel sub-assembly.



Hide 55735A 4.REMOVE WATER GUARD PLATE LH

a.

for LHD:

i.
C365624

Disengage the claw and remove the water guard plate LH.



b.

for RHD:

i.
C365625

Disengage the claw and remove the water guard plate LH.



Hide 55736D 5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

a.

for LHD:

i.
C365626

Remove the bolt and cowl body mounting reinforcement LH from the vehicle body.



b.

for RHD:

i.
C365627

Remove the bolt and cowl body mounting reinforcement LH from the vehicle body.



Hide 55735C 6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

a.

for LHD:

i.
C365628

Remove the 2 bolts and cowl body mounting reinforcement RH from the vehicle body.



b.

for RHD:

i.
C365629

Remove the 2 bolts and cowl body mounting reinforcement RH from the vehicle body.



Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

a.

w/ Windshield Deicer:

i.
C365630

Disconnect the connector.


ii.

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.



b.
C365632

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.


c.
C365634

Remove the 8 bolts, 4 nuts and outer cowl top panel sub-assembly.


Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

a.

w/ Windshield Deicer:

i.
C365631

Disconnect the connector.


ii.

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.



b.
C365633

Disengage the 2 clamps and separate the wire harness from the outer cowl top panel sub-assembly.


c.
C365635

Remove the 8 bolts, 4 nuts and outer cowl top panel sub-assembly.


Hide 48684B 9.REMOVE FRONT SUSPENSION SUPPORT DUST COVER

a.
C344895

Remove the front suspension support dust cover from the front shock absorber assembly.


Hide 48609E 10.LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C344897

Temporarily install the 2 nuts to the front shock absorber assembly.


b.
C344899

Loosen the front support to front shock absorber nut.

CAUTION:
C320511

·

Only loosen the front support to front shock absorber nut if the front shock absorber with coil spring needs to be disassembled.

·

Only loosen the front support to front shock absorber nut, do not remove it.

·

If the front support to front shock absorber nut is removed with the front coil spring under tension, components of the front shock absorber with coil spring may fly off.




Hide 48810 11.SEPARATE FRONT STABILIZER LINK ASSEMBLY

a.
C348712

Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



Hide 89543 12.SEPARATE FRONT SPEED SENSOR

a.
C344900

Disengage the clamp.


b.

Remove the bolt.


c.
C365638

Disengage the 2 hooks to separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



Hide 13.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C344901C02
2.188,1.417 2.833,1.417 true 0.813,2.188 1.354,2.188 false 2.875,1.354 3.188,1.51 0.313,0.156 10 false *a 0.646,2.115 0.958,2.271 0.313,0.156 10 false *b
*a Wooden Block
*b Jack
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.

NOTICE:

Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.



b.
C344902

Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

NOTICE:
·

When removing the nuts, keep the bolts from rotating.

·

Use wire or an equivalent tool to hang the separated steering knuckle.




c.
C351018

Remove the 3 nuts, 2 spacers and front shock absorber with coil spring.


Hide 48609E 14.REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

a.
C427981

Fold back the front spring seat sub-assembly with insulator.

HINT:

Check that the front spring seat sub-assembly with insulator is not excessively deformed or crushed.



b.
C427982C02
1.917,0.667 1.917,0.333 1.917,0.333 2.917,0.333 true 1.76,1.083 2.656,0.688 2.656,0.688 2.896,0.688 true 2.969,0.25 3.281,0.406 0.313,0.156 10 false *a 2.917,0.594 3.208,0.792 0.292,0.198 10 true *b
*a Cloth, etc.
*b Shock Rod


Using a piece of cloth, etc., clean the shock rod and remove any foreign matter and oil.

NOTICE:

Thoroughly clean the shock rod to prevent damage to the shock rod due to contact of foreign matter.



c.
C428022C02
1.167,2.375 1.167,2.292 1.167,2.292 1.333,2.292 true 2.76,2.375 2.76,2.292 2.76,2.292 2.927,2.292 true 1.135,3.406 1.135,3.323 1.135,3.323 1.302,3.323 true 2.719,3.396 2.719,3.313 2.719,3.313 2.885,3.313 true 1.375,2.229 1.688,2.385 0.313,0.156 10 false *1 1.354,3.24 1.667,3.396 0.313,0.156 10 false *2 2.969,2.229 3.281,2.385 0.313,0.156 10 false *1 2.938,3.24 3.25,3.396 0.313,0.156 10 false *2
*1 SST (09727-58100)
*2 SST (09727-58140)


Attach SST (09727-58140) to SST (09727-58100).

SST
09727-58100  
09727-58140  

NOTICE:

Check that there are no cracks or damage in SST (09727-58140) that could prevent it from securing the shock rod of the front shock absorber assembly.

If there are, replace SST (09727-58140) with a new one.



d.
C428012C02
1.646,0.938 1.854,0.344 1.854,0.344 2.104,0.344 true 2.729,1.885 2.563,1.885 2.563,1.885 2.448,1.542 true 2.167,0.271 2.51,0.458 0.344,0.188 10 false *a 2.802,1.802 3.25,2.01 0.448,0.208 10 false SST
*a Installation Surface


Clean the surface of SST (09727-58140) to which the front shock absorber assembly is installed and remove any foreign matter and oil.

NOTICE:

Thoroughly clean the installation surface to prevent damage to the shock rod due to contact of foreign matter.



e.
C427984N01
1.583,1.333 1.583,2 1.583,2 1.417,2 true 1.083,1.906 1.448,2.094 0.365,0.188 10 false SST

Using a long ball hexagon 5, install SST (09727-58100) and SST (09727-58140) to the shock rod.

NOTICE:

When installing SST (09727-58100) and SST (09727-58140), do not fold back the front spring seat sub-assembly with insulator in an improper direction and deform it.


HINT:
·

Install SST (09727-58100) and SST (09727-58140) to the base of the shock rod and check that SST (09727-58100) and SST (09727-58140) are securing the shock rod.

·

The front shock absorber assembly has a built-in rebound spring and is constructed to constantly contract the shock rod.

For this reason, it is difficult to sufficiently contract the coil spring to a level that frees the front suspension support sub-assembly using only the coil spring compressor (09727-30022), making it necessary for SST (09727-58100), SST (09727-58140) and a long ball hexagon 5 to be used to ensure a shock rod free length in which work can be performed with a small amount of compression.




f.
C287918N04
2.427,1.281 2.427,0.979 2.427,0.979 2.688,0.979 false 2.729,0.906 3.188,1.104 0.458,0.198 10 false SST

Secure SST in a vise.

SST
09727-00051  
09727-30022  (09727-00010, 09727-00031)


g.

Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:
·
C322989

Make sure that the hooks are securely attached to the coil spring.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344903

Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C312080

Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




h.

Install the stopper pins to the hooks of SST.

CAUTION:
C322990

·

Make sure that the stopper pins are installed securely.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.




i.
C344904C02
0.448,0.854 0.906,0.854 false 0.646,0.854 0.646,1.031 0.646,1.031 1.188,1.031 true 1.573,1.146 2.948,1.146 true 1.375,1.333 2.208,1.333 2.208,1.333 2.208,1.146 true 2.99,1.083 3.302,1.24 0.313,0.156 10 false SST 0.281,0.781 0.594,0.938 0.313,0.156 10 false *a
*a Vehicle Nut


Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST
09727-30022  (09727-00090, 09727-00100)


j.

Using SST, compress the coil spring.

CAUTION:
·
C344905

If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344906

Do not compress the coil spring to the point where the coils touch each other.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

·
C344907

Do not use an impact wrench.

·

If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.

·
C344908C02
0.792,3.125 1.74,3.125 true 0.49,3.042 0.802,3.198 0.313,0.156 10 false SST

If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.

·

If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.

·

If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.



SST
09727-00110  


k.

Check that the coil spring has become detached, and then remove the front support to front shock absorber nut.

CAUTION:
C344909

·

Do not remove the front support to front shock absorber nut while the coil spring is under tension.

·

If the front support to front shock absorber nut is removed with the coil spring under tension, components of the front shock absorber with coil spring may fly off, resulting in injury.




Hide 15.REMOVE COLLAR

a.

Remove the collar from the front shock absorber assembly.


Hide 48609 16.REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

a.

Remove the front suspension support sub-assembly from the front shock absorber assembly.


Hide 48045A 17.REMOVE FRONT SPRING SEAT SUB-ASSEMBLY WITH INSULATOR

a.
C344875C02
0.75,1.719 0.854,1.719 0.854,1.719 1.469,1.594 true 1.531,1.552 1.792,1.938 1.792,1.938 2.042,1.542 true 0.583,1.646 0.896,1.802 0.313,0.156 10 false *1 1.74,1.969 2.052,2.125 0.313,0.156 10 false *a
*1 Front Spring Seat Sub-assembly with Insulator
*a Claw


Disengage the front spring seat sub-assembly with insulator from the claws of the front shock absorber assembly.


b.

Remove the front spring seat sub-assembly with insulator from the front shock absorber assembly.


Hide 48132 18.REMOVE FRONT COIL SPRING

a.

Remove the front coil spring and SST.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 48331C 19.REMOVE FRONT SPRING BUMPER

a.
C365636C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front spring bumper from the front shock absorber assembly as shown in the illustration.


Hide 48158C 20.REMOVE FRONT LOWER COIL SPRING INSULATOR

a.

Remove the front lower coil spring insulator from the front shock absorber assembly.


Hide 48520 21.REMOVE FRONT SHOCK ABSORBER ASSEMBLY

a.

Using SST (09727-58010), remove SST (09727-58100) and SST (09727-58140) from the front shock absorber assembly.

SST
09727-58010  (09727-58030)

C428018C02
2.385,0.823 2.385,1.406 2.385,1.406 2.563,1.406 true 2.104,5.667 1.938,5.667 1.938,5.667 1.542,5.188 true 1.865,3.677 1.698,3.677 1.698,3.677 1.448,3.26 true 4.938,3.917 4.771,3.917 4.771,3.917 4.771,3.594 true 6.469,3.885 6.302,3.885 6.302,3.885 6.302,3.594 true 5,2.354 4.708,1.792 4.708,1.792 4.542,1.792 true 2.615,1.313 2.927,1.51 0.313,0.198 10 true *1 1.208,2.792 1.521,2.99 0.313,0.198 10 true *a 0.25,3.229 0.563,3.427 0.313,0.198 10 true *b 5,3.792 5.313,3.99 0.313,0.198 10 true *c 3.854,0.052 4.24,0.271 0.385,0.219 10 false [#2] 3.927,1.5 4.313,1.719 0.385,0.219 10 false [#3] 0.115,1.938 0.5,2.156 0.385,0.219 10 true [#4] 0.115,0.083 0.5,0.302 0.385,0.219 10 false [#1] 0.219,4.438 0.604,4.656 0.385,0.219 10 true [#5] 2.146,5.563 2.458,5.76 0.313,0.198 10 true *2 1.938,3.583 2.25,3.781 0.313,0.198 10 true *d 6.51,3.781 6.823,3.979 0.313,0.198 10 true *c 4.323,1.698 4.635,1.896 0.313,0.198 10 true *d
*1 Front Shock Absorber Assembly *2 Shock Absorber Outer Shell
*a Turn *b Hold
*c Fixing Nut *d Bolt


NOTICE:
C434261C02
0,0 0,0 false
V100155

Application Area


Apply molybdenum grease to the bolt (area with diagonal lines) of SST (09727-58010).


i.

Install SST (09727-58030) to the end of the shock rod of the front shock absorber assembly.[#1]


ii.

Install SST (09727-58010) to the front shock absorber assembly.[#2]

NOTICE:

Take due care when installing SST (09727-58010) to ensure the shock rod is not damaged.



iii.

Secure the SST (09727-58010) bolt and SST (09727-58030) with the fixing nut.[#3]


iv.

After securing the SST (09727-58010) bolt, rotate the nut clockwise.[#4]

NOTICE:

Extend the shock rod until SST (09727-58100) and SST (09727-58140) separate from the shock absorber outer shell.



v.

Using a long ball hexagon 5, remove SST (09727-58100) and SST (09727-58140).[#5]

NOTICE:

If SST (09727-58100) and SST (09727-58140) are removed without using SST (09727-58010), the action of the rebound spring will cause the shock rod to contract suddenly. Therefore, remove SST (09727-58100) and SST (09727-58140) after securing the shock rod with SST (09727-58010).



vi.

Using a piece of cloth, etc., clean the shock rod of the front shock absorber assembly and remove any foreign matter and oil.

NOTICE:

If the shock rod is expanded/contracted while foreign matter or oil are still present, it may damage the front shock absorber assembly or cause oil leaks.



vii.

After securing the SST (09727-58010) bolt, rotate the nut counterclockwise.


viii.

Check that the shock rod and SST (09727-58030) have become free before releasing the fixing nut and removing SST (09727-58010) from the shock rod.

NOTICE:

Take due care when removing SST (09727-58010) to ensure the shock rod is not damaged.



ix.

Remove SST (09727-58030) from the end of the shock rod.


x.

Using a piece of cloth, etc., clean the end of the shock rod threads and remove any foreign matter and oil.