Home › Suspension › FRONT SUSPENSION › FRONT LOWER BALL JOINT
RM32H0E _53 Suspension _059519 FRONT SUSPENSION _0291585 FRONT LOWER BALL JOINT A

FRONT SUSPENSION  FRONT LOWER BALL JOINT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front lower ball joint assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT AXLE ASSEMBLY

Hide 43340A 2.REMOVE FRONT LOWER BALL JOINT ASSEMBLY

a.
C345012

Secure the front axle assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C345013

Remove the cotter pin.


c.

Remove the nut.


d.
C345014C02
0.938,1.094 0.938,0.24 true 1.073,1.135 1.073,0.24 1.073,0.24 0.844,0.24 false 3.083,0.917 3.396,1.073 0.313,0.156 10 false *a 0.542,0.156 1,0.354 0.458,0.198 10 false SST
*a 1 mm (0.0394 in.)


Install SST to the front lower ball joint assembly as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.0394 in.).



e.
C345015C02
1.698,1.615 2.698,1.615 false 2.219,2.417 2.635,1.938 2.635,1.938 2.74,1.938 true 1.01,4.365 1.125,4.365 1.125,4.365 1.333,3.99 false 1.542,1.271 1.99,1.271 false 0.833,4.271 1.146,4.427 0.313,0.156 10 false *a 2.438,0.656 2.75,0.813 0.313,0.156 10 false *b 1.365,1.167 1.677,1.323 0.313,0.156 10 false *c 2.792,1.854 3.104,2.01 0.313,0.156 10 false *d 2.438,0.281 2.75,0.438 0.313,0.156 10 false *b 2.76,1.531 3.073,1.688 0.313,0.156 10 false SST 2.208,3.49 2.521,3.646 0.313,0.156 10 false A 2.208,3.771 2.521,3.927 0.313,0.156 10 false B
*a Center Nut
*b Molybdenum Grease Application Area
*c Place wrench here
*d String
V113147

Turn


Using SST, remove the front lower ball joint assembly from the front axle assembly as shown in the illustration.

SST
09960-20010  (09961-02010, 09961-02050)

NOTICE:
·

Apply molybdenum grease to the threads and end of the SST bolt.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the front lower ball joint dust cover may be damaged.

·

Be sure to place a wrench on the part shown in the illustration.

·

Do not damage the front lower ball joint dust cover.

·

Do not damage the steering knuckle.

·

Do not damage the front disc brake dust cover.