Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2016.10–2019.09
RM32H0E _55 Steering _059605 POWER ASSIST SYSTEMS _0292301 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


NOTICE:
·

It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specification.

·

Turn the ignition switch to ON and park the vehicle on level ground. Check the freeze frame data by using the GTS.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Check the freeze frame data on the GTS.

Chassis > EMPS
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from speedometer Min.: 0.0 km/h (0.0 MPH)
Max.: 300.0 km/h (186.4 MPH)
·

0 km/h (0 MPH): Engine running and vehicle stopped

·

No significant fluctuation: Engine running and vehicle driven at a constant speed


-
Wheel Speed Right Rear right wheel speed Min.: 0 km/h (0 MPH)
Max.: 255 km/h (158 MPH)
·

0 km/h (0 MPH): Engine running and vehicle stopped

·

No significant fluctuation: Engine running and vehicle driven at a constant speed


-
Wheel Speed Left Rear left wheel speed Min.: 0 km/h (0 MPH)
Max.: 255 km/h (158 MPH)
·

0 km/h (0 MPH): Engine running and vehicle stopped

·

No significant fluctuation: Engine running and vehicle driven at a constant speed


-
Engine Revolution Engine speed Min.: 0 rpm
Max.: 12800 rpm
No significant fluctuation Engine running at a constant speed
Motor Actual Current Amount of current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right
Engine running and steering wheel being turned
Command Value Current Requested current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right
Engine running and steering wheel being turned
Steering Angle Velocity Steering angle speed Min.: -32768 deg/s
Max.: 32767 deg/s
Value changes in proportion to steering speed
- The value increases when turning left and decreases when turning right
Engine running and steering wheel being turned
Thermistor Temperature ECU substrate temperature Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F)
-50°C to 150°C (-58°F to 302°F) -
IG Power Supply IG power source voltage Min.: 0.0000 V
Max.: 20.1531 V
8 to 16 V Ignition switch ON
Steering Wheel Torque Steering wheel torque Min.: -7.00 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right
Engine running and steering wheel being turned
Motor Rotation Angle Motor rotation angle Min.: 0.000 deg
Max.: 360.000 deg
During steering operation, motor rotation angle value changes from 0 to 360° Engine running and steering wheel being turned
Command Val Current 2 Requested current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Motor Voltage Motor power supply voltage Min.: 0.000 V
Max.: 98.000 V
9 to 16 V Engine running and steering wheel being turned
TRQ1 Zero Point Value Zero point value of torque sensor 1 Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Engine running and steering wheel not being turned (without load)
TRQ2 Zero Point Value Zero point value of torque sensor 2 Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Engine running and steering wheel not being turned (without load)
PS Assist Signal Status of the record of power steering assist signal OFF or ON OFF: Ignition switch ON
ON: Engine running
-
Motor Actual Current 2 Amount of current to motor Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Stop&Start Ctrl Mode Status of the record of stop and start control mode IG, Run, Stopreq, Stop, Restart IG: Ignition switch ON (Before engine started)
Run: Engine running
Stopreq: Engine stop requested
Stop: Engine stopped
Restart: Engine restarting
-
Steering Angle Steering angle Min.: -3072.0 deg
Max.: 3070.5 deg
- -
Torque Sensor 1 Output Torque sensor 1 output value Min.: 0.0000 V
Max.: 4.9725 V
- -
Torque Sensor 2 Output Torque sensor 2 output value Min.: 0.0000 V
Max.: 4.9725 V
- -
Torque Sensor 1 Power Supply Torque sensor 1 power supply voltage Min.: 0.0000 V
Max.: 4.9725 V
- -
Torque Sensor 2 Power Supply Torque sensor 2 power supply voltage Min.: 0.0000 V
Max.: 4.9725 V
- -
Rotation Angle Sensor Output 1 Rotation angle sensor Vx1 output voltage Min.: 0.0000 V
Max.: 4.9725 V
- -
Rotation Angle Sensor Output 2 Rotation angle sensor Vx2 output voltage Min.: 0.0000 V
Max.: 4.9725 V
- -
Rotation Angle Sensor Output 3 Rotation angle sensor Vy1 output voltage Min.: 0.0000 V
Max.: 4.9725 V
- -
Rotation Angle Sensor Output 4 Rotation angle sensor Vy2 output voltage Min.: 0.0000 V
Max.: 4.9725 V
- -
Motor 1 Terminal Current (U) Motor 1 terminal current (U phase) Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Motor 1 Terminal Current (V) Motor 1 terminal current (V phase) Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Motor 1 Terminal Current (W) Motor 1 terminal current (W phase) Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Motor 2 Terminal Current (U) Motor 2 terminal current (U phase) Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Motor 2 Terminal Current (V) Motor 2 terminal current (V phase) Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Motor 2 Terminal Current (W) Motor 2 terminal current (W phase) Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Engine running and steering wheel being turned
Motor 1 U Phase Duty Motor 1 U phase duty Min.: 0.00%
Max.: 100.00%
- -
Motor 1 V Phase Duty Motor 1 V phase duty Min.: 0.00%
Max.: 100.00%
- -
Motor 1 W Phase Duty Motor 1 W phase duty Min.: 0.00%
Max.: 100.00%
- -
Motor 2 U Phase Duty Motor 2 U phase duty Min.: 0.00%
Max.: 100.00%
- -
Motor 2 V Phase Duty Motor 2 V phase duty Min.: 0.00%
Max.: 100.00%
- -
Motor 2 W Phase Duty Motor 2 W phase duty Min.: 0.00%
Max.: 100.00%
- -
Motor 1 Terminal Volt (U) Motor 1 terminal voltage (U phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor 1 Terminal Volt (V) Motor 1 terminal voltage (V phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor 1 Terminal Volt (W) Motor 1 terminal voltage (W phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor 2 Terminal Volt (U) Motor 2 terminal voltage (U phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor 2 Terminal Volt (V) Motor 2 terminal voltage (V phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor 2 Terminal Volt (W) Motor 2 terminal voltage (W phase) Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Engine running and steering wheel being turned
Motor 1 PIG Power Supply Power supply voltage to active motor 1 Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Engine running and steering wheel being turned
Motor 2 PIG Power Supply Power supply voltage to active motor 2 Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Engine running and steering wheel being turned