Home › Drivetrain › K114 (MULTIDRIVE / CVT) › REVOLUTION SENSOR
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292455 REVOLUTION SENSOR G

K114 MULTIDRIVE / CVT  REVOLUTION SENSOR  INSPECTION  


PROCEDURE

Hide 89413P 1.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)

C200614C02
1.219,1.677 1.521,1.156 false 2.219,1.688 1.917,1.167 false 1,1.719 1.448,1.917 0.448,0.198 10 NIN+ 2.167,1.729 2.615,1.927 0.448,0.198 10 NIN- 0.229,0.156 0.542,0.354 0.313,0.198 10 *a
*a Component without harness connected
(Transmission Revolution Sensor (NIN))


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω


If the result is not as specified, replace the transmission revolution sensor (NIN).


Hide 89413M 2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

a.

Connect the battery to the transmission revolution sensor (NOUT) as shown in the illustration.


b.
C279306C08
0.833,0.656 1.479,0.656 false 1.865,0.719 2.5,0.719 false 0.875,2.479 1.354,2.479 false 0.26,2.292 0.531,2.292 false 0.427,0.573 0.906,0.885 0.479,0.313 10 false NOTB 0.156,0.083 0.469,0.354 0.313,0.271 10 false *a 2.573,0.635 3.063,0.927 0.49,0.292 10 false NOTO 1.51,1.719 1.813,1.958 0.302,0.24 10 false *d 1.49,4.094 1.802,4.292 0.313,0.198 10 false *c 1.427,2.396 1.594,2.604 0.167,0.208 10 false 1 0.146,2.208 0.396,2.448 0.25,0.24 10 false 2 2.396,2.365 2.708,2.563 0.313,0.198 10 false *1 2.219,3.813 2.573,4.052 0.354,0.24 10 false *b
*1 Battery
*a Component without harness connected
(Transmission Revolution Sensor (NOUT))
*b Magnet
*c 5 mm (0.197 in.) gap or closer
*d Ammeter


Wave a magnetic object left and right in front of the tip of the transmission revolution sensor (NOUT) (5 mm (0.197 in.) gap or closer) to change the high/low signals while measuring the current.

NOTICE:

Be sure to wave a magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low Signal 4 to 8 mA
High Signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NOUT).


Hide 89413N 3.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

a.

Connect the battery to the transmission revolution sensor (NT) as shown in the illustration.


b.
C279306C07
0.833,0.656 1.479,0.656 false 1.865,0.719 2.531,0.719 false 0.875,2.479 1.365,2.479 false 0.26,2.292 0.531,2.292 false 0.542,0.573 0.969,0.906 0.427,0.333 10 false NTB 0.156,0.083 0.469,0.354 0.313,0.271 10 false *a 2.604,0.635 3.094,0.927 0.49,0.292 10 false NTO 1.51,1.719 1.813,1.958 0.302,0.24 10 false *d 1.552,4.052 1.865,4.25 0.313,0.198 10 false *c 2.229,3.813 2.542,4.01 0.313,0.198 10 false *b 1.438,2.396 1.604,2.604 0.167,0.208 10 false 1 0.146,2.208 0.396,2.448 0.25,0.24 10 false 2 2.385,2.354 2.698,2.552 0.313,0.198 10 false *1
*1 Battery
*a Component without harness connected
(Transmission Revolution Sensor (NT))
*b Magnet
*c 5 mm (0.197 in.) gap or closer
*d Ammeter


Wave a magnetic object left and right in front of the tip of the transmission revolution sensor (NT) (5 mm (0.197 in.) gap or closer) to change the high/low signals while measuring the current.

NOTICE:

Be sure to wave a magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low Signal 4 to 8 mA
High Signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NT).