Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the driver side and front passenger side.
The procedure listed below is for the driver side.
72443B
1.INSTALL VERTICAL ADJUSTER GEAR LH (w/ Vertical Adjuster)
Install the front seat vertical adjuster assembly.
Install the front vertical adjuster brake sub-assembly LH.
Make sure to insert the stud bolt of the front vertical adjuster brake sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.
Install the vertical adjuster spacer.
Install the vertical adjuster plate with the 3 nuts.
Tighten the nuts in the order shown in the illustration.
82824A
2.INSTALL CONNECTOR MALE HOUSING (w/o Seat Heater System)
Engage the claw to install the connector male housing.
82667D
3.INSTALL CONNECTOR HOLDER (for Front Passenger Side)
Engage the claw to install the connector holder.
72211C
4.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the claws to install the seat track adjusting handle to the front seat adjuster assembly.
71052A
5.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage the hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
7181B
6.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER
Engage the claw to install the front seat cushion wire harness holder.
Install the 2 screws.
82192
7.INSTALL FRONT SEAT WIRE (for Driver Side)
Engage the claw.
Disengage the clamps to install the front seat wire.
82191
8.INSTALL FRONT SEAT WIRE (for Front Passenger Side)
Engage the claw.
Disengage the clamps to install the front seat wire.
8219B
9.INSTALL NO. 2 FRONT SEAT WIRE (w/ Seat Position Airbag Sensor)
Engage the claw and clamp to install the No. 2 front seat wire.
71875G
10.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Driver Side)
Engage the claws to install the LH seat reclining adjuster inside cover RH.
71876G
11.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Driver Side)
Engage the claws to install the LH seat reclining adjuster inside cover LH.
w/ Lumbar Support:
Engage the claw.
71875F
12.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER RH (for Front Passenger Side)
Engage the claws to install the RH seat reclining adjuster inside cover RH.
71876F
13.INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER LH (for Front Passenger Side)
Engage the claws to install the RH seat reclining adjuster inside cover LH.
71873A
14.INSTALL FRONT SEAT LOWER CUSHION SHIELD (w/ Vertical Adjuster)
| *a | Hook |
| *b | Guide |
Engage the claw and guide.
Engage the hook to install the front seat lower cushion shield.
71874A
15.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)
| *a | Hook |
| *b | Guide |
Engage the claw and guide.
Engage the hook to install the front seat lower cushion shield LH.
87510L
16.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71072S
17.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION
Engage the claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
Be careful not to damage the separate type front seat cushion cover.
18.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the hooks (A) and hooks (B) to install the separate type front seat cushion cover with pad.
Engage the hooks.
for Front Passenger Side:
Engage the claw to install the occupant detection sensor connector.
w/ Seat Heater System:
Connect the connector.
Engage the clamp.
82192B
19.INSTALL NO. 2 FRONT SEAT WIRE (w/ Lumbar Support)
Engage the clamp to install the No. 2 front seat wire.
71759B
20.INSTALL FRONT SEATBACK HOOK
Engage the claws to install the 2 front seatback hooks from the front seatback frame sub-assembly.
71054S
21.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Lumbar Support)
Install the 2 front seatback edge protectors to the front seatback spring sub-assembly.
|
Install in this Direction |
Engage the guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.
Engage the claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.
72760D
22.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)
73920A
23.INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
87510N
24.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71074S
25.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION
w/ Front Seat Airbag Assembly:
Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.
Be careful not to damage the separate type front seatback cover.
w/o Front Seat Airbag Assembly:
Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.
Be careful not to damage the separate type front seatback cover.
26.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.
71931
27.INSTALL FRONT SEAT HEADREST SUPPORT
|
Install in this Direction |
Engage the claws to install the 2 front seat headrest supports as shown in the illustration.
Close the 2 fasteners as shown in the illustration.
w/ Seat Heater System:
Engage the clamp.
Engage the hooks.
28.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.
Install the 4 bolts.
w/ Front Seat Side Airbag
Engage the claw and clamps to install the front seat airbag assembly wire harness.
Engage the claw first.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
w/ Lumbar Support:
Engage the clamp.
Connect the connector.
Engage the hooks.
72497B
29.INSTALL VERTICAL ADJUSTER BRACKET COVER (w/ Vertical Adjuster)
Engage the claw to install the vertical adjuster bracket cover.
71862
30.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)
|
Install in this Direction |
Engage the claws and guides as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat inner cushion shield as shown in the illustration.
84922A
31.INSTALL FRONT LUMBAR POWER SEAT SWITCH (w/ Lumbar Support)
71812D
32.INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)
w/ Lumbar Support:
Connect the connector.
Engage the clamps.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the claws and guides (B) as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat cushion shield as shown in the illustration.
71849F
33.INSTALL SEAT ADJUSTER COVER CAP (w/ Vertical Adjuster)
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides as shown in the illustration.
Engage the claws to install the seat adjuster cover cap as shown in the illustration.
71861
34.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
|
Install in this Direction |
Engage the claws and guides as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat inner cushion shield as shown in the illustration.
71811D
35.INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the claws and guides (B) as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat cushion shield as shown in the illustration.
72526A
36.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the guide to install the reclining adjuster release handle.
72538
37.INSTALL RECLINING HINGE OUTER COVER
|
Install in this Direction |
Engage the guide and claw to install the reclining hinge outer cover as shown in the illustration.
72495
38.INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)
|
Install in this Direction |
Engage the claw to install the vertical adjusting handle as shown in the illustration.
71074S
39.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73240
40.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
41.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
87501B
42.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
89178A
43.INSTALL SEAT POSITION AIRBAG SENSOR (w/ Seat Position Airbag Sensor)
for 6 Way Seat Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>INSTALLATION
for 4 Way Seat Type:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>INSTALLATION
72277A
44.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (w/ Seat Position Airbag Sensor)