Wear protective gloves. Sharp areas on the parts may injure your hands.
73178A
1.REMOVE SEAT BELT ANCHOR COVER CAP (for RH Side)
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Using a moulding remover A, disengage the claws and guides to separate the rear seat shoulder belt cover with seat belt anchor cover cap as shown in the illustration.
|
Remove in this Direction |
Disengage the guides to remove the seat belt anchor cover cap as shown in the illustration.
73373F
2.REMOVE REAR SEAT SHOULDER BELT HOLE COVER (for RH Side)
Remove the rear seat shoulder belt hole cover.
72679
3.REMOVE REAR SEATBACK LOCK CONTROL BEZEL (for RH Side)
Disengage the claws to remove the rear seatback lock control bezel.
Disengage the hooks from the separate type rear seatback cover.
71701C
4.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH (for RH Side)
Disengage the hook.
| *a | Fastener |
Open the 2 fasteners as shown in the illustration.
Disengage the claws and guides to remove the rear seatback board sub-assembly RH.
71931A
5.REMOVE REAR SEAT HEADREST SUPPORT (for RH Side)
|
Remove in this Direction |
Disengage the claws to remove the 2 rear seat headrest supports as shown in the illustration.
71931A
6.REMOVE REAR SEAT CENTER HEADREST SUPPORT (w/ Center Headrest)
|
Remove in this Direction |
Disengage the claws to remove the 2 rear seat center headrest supports as shown in the illustration.
7.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)
Pass the rear center seat outer belt assembly through the separate type rear seatback cover with pad and remove the separate type rear seatback cover with pad from the rear seatback frame sub-assembly RH.
71077S
8.REMOVE SEPARATE TYPE REAR SEATBACK COVER (for RH Side)
Using a screwdriver, disengage the claws to remove the separate type rear seatback cover from the separate type rear seatback pad RH as shown in the illustration.
| *a | Screwdriver | - | - |
73350C
9.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side)
72630C
10.REMOVE REAR SEATBACK LOCK ASSEMBLY RH (for RH Side)
Remove the 2 bolts.
Disengage the guides to rear seatback lock assembly RH.
72679
11.REMOVE REAR SEATBACK LOCK CONTROL BEZEL (for LH Side)
Disengage the claws to remove the rear seatback lock control bezel.
Disengage the hooks from the separate type rear seatback cover.
71702C
12.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH (for LH Side)
Disengage the hook.
| *a | Fastener |
Open the 2 fasteners as shown in the illustration.
Disengage the claws and guides to remove the rear seatback board sub-assembly LH.
71931A
13.REMOVE REAR SEAT HEADREST SUPPORT (for LH Side)
|
Remove in this Direction |
Disengage the claws to remove the 2 rear seat headrest supports as shown in the illustration.
14.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)
Remove the separate type rear seatback cover with pad from the rear seatback frame sub-assembly LH.
71078S
15.REMOVE SEPARATE TYPE REAR SEATBACK COVER (for LH Side)
Using a screwdriver, disengage the claws to remove the separate type rear seatback cover from the separate type rear seatback pad LH as shown in the illustration.
| *a | Screwdriver | - | - |
72640A
16.REMOVE REAR SEATBACK LOCK ASSEMBLY LH (for LH Side)
Remove the 2 bolts.
Disengage the guides to rear seatback lock assembly LH.
73731B
17.REMOVE NO. 1 CHILD RESTRAINT SEAT COVER (w/ Cover)
|
Remove in this Direction |
Disengage the claws and guides to remove the No. 1 child restraint seat cover as shown in the illustration.
Use the same procedure for all No. 1 child restraint seat covers.
73731C
18.REMOVE NO. 2 CHILD RESTRAINT SEAT COVER (w/ Cover)
|
Remove in this Direction |
Disengage the claws to remove the No. 2 child restraint seat cover as shown in the illustration.
Use the same procedure for all No. 2 child restraint seat covers.
73735
19.REMOVE CHILD RESTRAINT SEAT GUIDE CUP (w/ Cover)
Remove the child restraint seat guide cup.
Use the same procedure for all child restraint seat guide cups.
71075B
20.REMOVE BENCH TYPE REAR SEAT CUSHION COVER
for 2WD:
Disengage the hook and loop fastener and hooks.
| *a | Hook and Loop Fastener | - | - |
Remove the rear seat cushion pad from the No. 1 rear seat cushion pad sub-assembly.
for 4WD:
Disengage the hook and loop fastener and hooks.
| *a | Hook and Loop Fastener | - | - |
Remove the rear seat cushion pad from the No. 1 rear seat cushion pad sub-assembly.
Using a screwdriver, disengage the claws to remove the bench type rear seat cushion cover from the No. 1 rear seat cushion pad sub-assembly as shown in the illustration.
| *a | Screwdriver | - | - |