Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2820  Pressure Control Solenoid "J" Performance or Stuck Off  


DESCRIPTION

According to current control by the ECM, the shift solenoid valve SLP controls primary pulley pressure in accordance with the requested gear ratio to perform gear ratio changes.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2820 Pressure Control Solenoid "J" Performance or Stuck Off Either one of the following conditions is met (1 trip detection logic):
·

When the oil pressure sensor output is 0.333 MPa (3.4 kgf/cm2, 48 psi) or more and the target gear ratio is less than 1.0, the actual gear ratio is 2.0 or more for 2 seconds or more.

·

When the oil pressure sensor output is 0.333 MPa (3.4 kgf/cm2, 48 psi) or more and the target gear ratio is 2.0 or more, the actual gear ratio is less than 0.5 for 1.5 seconds or more.


Continuously variable transaxle assembly (Shift solenoid valve SLP) Comes on DTC stored

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The oil pressure sensor output value is 0.333 MPa (3.4 kgf/cm2, 48 psi) or more and the target gear ratio is less than 1.0. ○ -
The oil pressure sensor output value is 0.333 MPa (3.4 kgf/cm2, 48 psi) or more and the target gear ratio is 2.0 or more. - ○
Malfunction Condition The actual gear ratio is 2.0 or more. ○ -
The actual gear ratio is less than 0.5. - ○
Duration 2 seconds or more 1.5 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is output when either of the above detection patterns is met.


MONITOR DESCRIPTION

The ECM compares the actual gear ratio with the target gear ratio. When the actual gear ratio and target gear ratio are different, the ECM detects the malfunction, illuminates the MIL and stores this DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2820)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P2820 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Only DTC P2820 is output A
DTC P2820 and other DTCs are output B



A

2.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

2.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT