The ECM uses the shift solenoid valves SC and SL to switch control of the shift solenoid valve SLU between forward and reverse clutch control and lock-up control in response to driving conditions.
If DTC P07407F is stored after the engine has stalled, the lock-up shift solenoid valve (shift solenoid valve SL) may be malfunctioning.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P07407F | Torque Converter Clutch Actuator Stuck Off | One of the following conditions is met (2 trip detection logic):
·
When the ECM sends a lock-up OFF command and turns the shift solenoid valves SC and SL OFF, the difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less for 1 second or more. ·
When the ECM turns the shift solenoid valves SC and SL ON, the difference between the input turbine speed (NT) and primary pulley speed (NIN) is 300 rpm or more for 1 second or more. ·
While the vehicle is driven, a lock-up ON command is sent, but lock-up control is not performed for 1 second or more. |
·
Torque converter assembly ·
Continuously variable transaxle assembly |
Comes on (Euro-OBD)
Does not come on (Except Euro-OBD) |
DTC stored | SAE Code:
P0741 |
| P099A7F | Shift Solenoid "G" Control Actuator Stuck Off | One of the following conditions is met (2 trip detection logic):
·
When the ECM sends a lock-up ON command and turns the shift solenoid valves SC and SL ON, the difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less for 1 second or more. ·
When the ECM turns the shift solenoid valves SC and SL OFF, the difference between the input turbine speed (NT) and primary pulley speed (NIN) is 300 rpm or more for 1 second or more. ·
While the vehicle is driven, a lock-up ON command is sent, but lock-up control is not performed for 1 second or more. |
·
Torque converter assembly ·
Continuously variable transaxle assembly |
Comes on (Euro-OBD)
Does not come on (Except Euro-OBD) |
DTC stored | SAE Code:
P075B |
| P27567F | Torque Converter Clutch Pressure Control Solenoid Control Actuator Stuck Off | One of the following conditions is met (2 trip detection logic):
·
When the ECM sends a lock-up ON command and turns the shift solenoid valves SC and SLU OFF and SL ON, the difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less for 1 second or more. ·
While the vehicle is driven, a lock-up signal is turned ON, but the lock-up remains OFF for 1 second or more. |
·
Torque converter assembly ·
Continuously variable transaxle assembly |
Comes on (Euro-OBD)
Does not come on (Except Euro-OBD) |
DTC stored | SAE Code:
P2757 |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnostic Condition | The ECM sends a lock-up OFF command and turns the shift solenoid valves SC and SL OFF. | ○ | - | - |
| The ECM turns the shift solenoid valves SC and SL ON. | - | ○ | - | |
| The vehicle is being driven. | - | - | ○ | |
| Malfunction Condition | The difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less. | ○ | - | - |
| The difference between the input turbine speed (NT) and primary pulley speed (NIN) is 300 rpm or more. | - | ○ | - | |
| The lock-up ON command is sent, but lock-up control is not performed. | - | - | ○ | |
| Duration | 1 second or more | 1 second or more | 1 second or more | |
| Detection Logic | 2 trip detection logic | 2 trip detection logic | 2 trip detection logic | |
This DTC is output when any one of the above detection patterns is met.
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnostic Condition | The ECM turns the shift solenoid valves SC and SL OFF. | ○ | - | - |
| The vehicle is being driven. | - | ○ | - | |
| The ECM sends a lock-up ON command and turns the shift solenoid valves SC and SL ON. | - | - | ○ | |
| Malfunction Condition | The difference between the input turbine speed (NT) and primary pulley speed (NIN) is 300 rpm or more. | ○ | - | - |
| The lock-up ON command is sent, but lock-up control is not performed. | - | ○ | - | |
| The difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less. | - | - | ○ | |
| Duration | 1 second or more | 1 second or more | 1 second or more | |
| Detection Logic | 2 trip detection logic | 2 trip detection logic | 2 trip detection logic | |
This DTC is output when any one of the above detection patterns is met.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnostic Condition | The ECM sends a lock-up ON command, and turns the shift solenoid valves SC and SLU OFF and SL ON. | ○ | - |
| The vehicle is being driven. | - | ○ | |
| Malfunction Condition | The difference between the engine speed (NE) and input turbine speed (NT) is 25 rpm or less. | ○ | - |
| The lock-up signal is turned ON, but the lock-up remains OFF. | - | ○ | |
| Duration | 1 second or more | 1 second or more | |
| Detection Logic | 2 trip detection logic | 2 trip detection logic | |
This DTC is output when either of the above detection patterns is met.
When performing lock-up control (on/off) of the torque converter, the ECM compares the transmission revolution sensor (NT) output speed and engine speed (NE) to detect mechanical malfunctions in the shift solenoid valves SL and SC.
If the torque converter does not lock-up while a lock-up ON command is being sent, the ECM detects it as a mechanical malfunction of the shift solenoid valve SLU.
If the difference between the engine speed (NE) and transmission revolution sensor (NT) output speed or transmission revolution sensor (NIN) output speed and transmission revolution sensor (NT) output speed is outside of the threshold, the ECM detects the malfunction, illuminates the MIL* and stores a DTC.
*: Euro-OBD
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Turn the ignition switch off.
Perform step (1) again.
Check for DTCs again.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
If any DTCs other than P07407F, P099A7F or P27567F are output, perform troubleshooting for those DTCs first.
| Result | Proceed to |
|---|---|
| Only DTC P07407F, P099A7F and/or P27567F is output | A |
| DTC P07407F, P099A7F and/or P27567F and other DTCs are output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Strictly observe posted speed limits, traffic laws and road conditions when performing a road test.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform the test with the air conditioning off.
Lock-up control will not operate when the CVT fluid temperature is 40°C (104°F) or less and the vehicle speed is 60 km/h (37 mph) or less, or when the CVT fluid temperature is 5°C (41°F) or less.
Lock-up control will not operate when the engine coolant temperature is 30°C (86°F) or less.
The lock-up OFF vehicle speed may vary depending on the electrical load, and air conditioning and brake operations.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Engine Speed, NT Sensor Speed, NIN Sensor Speed, Lock Up Status, Solenoid (SL) and Solenoid (SC).
| Tester Display |
|---|
| Engine Speed |
| NT Sensor Speed |
| NIN Sensor Speed |
| Lock Up Status |
| Solenoid (SL) |
| Solenoid (SC) |
According to the display on the GTS, read the Data List while driving.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383 rpm |
680 to 780 rpm: Idling (shift lever in N, engine warmed up and A/C switch off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| NT Sensor Speed | Input turbine speed (NT) | Min.: 0 rpm
Max.: 12750 rpm |
·
Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (After warming up engine) ·
Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (Idling with shift lever in P or N) ·
0 rpm: Vehicle stopped with shift lever in R |
Data is displayed in increments of 50 rpm. |
| NIN Sensor Speed | Primary pulley speed (NIN) | Min.: 0 rpm
Max.: 12750 rpm |
·
0 rpm: Vehicle stopped ·
Primary pulley speed (NIN) equal to engine speed (NE): Lock-up ON (After warming up engine) |
Data is displayed in increments of 50 rpm. |
| Lock Up Status | Lock-up | OFF or ON | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Solenoid (SL) | Shift solenoid valve SL status | OFF or ON | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Solenoid (SC) | Shift solenoid valve SC status | OFF or ON | ·
ON: For 1 second after moving shift lever from P to D or R, or N to D or R ·
ON: Lock-up ON to OFF ·
OFF: Engine idling |
- |
| Result | Proceed to |
|---|---|
| When Lock Up Status is ON, the input turbine speed (NT) is lower than the engine speed (NE). | A |
| When the shift solenoid valves SC and SL are OFF, the input turbine speed (NT) is equal to the engine speed (NE). | |
| When the shift solenoid valves SC and SL are ON, there is a large difference between the input turbine speed (NT) and the primary pulley speed (NIN). | |
| When Lock Up Status is ON, the input turbine speed (NT) is equal to the engine speed (NE). | B |
| When the shift solenoid valves SC and SL are OFF, the input turbine speed (NT) is lower than the engine speed (NE). | |
| When the shift solenoid valves SC and SL are ON, the input turbine speed (NT) is equal to the primary pulley speed (NIN). |
A
B
Replace the continuously variable transaxle assembly and torque converter assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT