Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM32H0E _59 Vehicle Exterior _059645 MIRROR (EXT) _0292588 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (for LED Type Turn Signal Light)

a.
B458224C01
1.219,3.635 0.698,3.354 true 1.198,3.781 0.677,4.115 true 1.354,3.792 1.604,4.146 true 0.729,2.906 1.042,3.063 0.313,0.156 10 false *a 0.438,3.271 0.75,3.427 0.313,0.156 10 false MV 0.417,4.031 0.729,4.188 0.313,0.156 10 false MH 1.5,4.167 1.813,4.323 0.313,0.156 10 false M+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror surface.

i.

Apply battery voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)
Turns upward
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)
Turns right
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.
B458225C01
1.698,3.625 2.177,3.031 true 1.656,3.802 2.177,4.302 true 0.708,2.781 1.021,2.938 0.313,0.156 10 false *a 2.26,2.938 2.573,3.094 0.313,0.156 10 false + 2.271,4.219 2.583,4.375 0.313,0.156 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (+) - 12 (-) 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, check the outer mirror LH.


ii.

Connect a cable from the positive (+) battery terminal to terminal 4 and the negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror LH.



c.
B458226C01
1.594,1.354 1.24,1.844 true 2.635,0.823 2.313,1.125 true 0.24,0.125 0.552,0.281 0.313,0.156 10 false *a 2.719,0.75 3.198,0.948 0.479,0.198 10 false BSL+ 1.198,1.865 1.354,2.063 0.156,0.198 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the blind spot monitor indicator.

NOTICE:

Do not apply a voltage of 6 V or higher.


i.

Check the operation of the blind spot monitor indicator.


ii.

Connect 4 dry-cell batteries (1.5 V each) in series.


iii.

Connect a positive (+) lead from the batteries to terminal 8 (BSL+) and a negative (-) lead to terminal 12 (-) and check that the blind spot monitor indicator comes on.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 8 (BSL+)
Battery negative (-) → Terminal 12 (-)
Blind spot monitor indicator comes on


If the result is not as specified, check the outer mirror LH.



d.
B458227C01
1.552,3.844 1.146,3.313 true 1.552,4.01 1.24,4.344 true 0.438,3.021 0.75,3.177 0.313,0.156 10 false *a 1.323,0.052 1.635,0.208 0.313,0.156 10 false (A) 0.948,1.083 1.26,1.281 0.313,0.198 10 false (B) 1.146,2.135 1.458,2.333 0.313,0.198 10 false (C) 1.635,2.427 1.948,2.625 0.313,0.198 10 false (D) 2.177,2.74 2.49,2.938 0.313,0.198 10 false (E) 0.896,3.26 1.208,3.417 0.313,0.156 10 false MR 0.979,4.26 1.292,4.417 0.313,0.156 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the retractable mirror. (w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87940 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (for Bulb Type Turn Signal Light)

a.
B450635C03
2.125,3.604 2.625,3.125 true 2.094,3.781 2.573,4.156 true 1.906,3.781 1.438,4.115 true 1.021,2.896 1.333,3.052 0.313,0.156 10 false *a 2.646,2.906 2.958,3.063 0.313,0.156 10 false MV 2.625,4.104 2.938,4.26 0.313,0.156 10 false M+ 1.188,4.083 1.5,4.24 0.313,0.156 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror surface.

i.

Apply voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 14 (M+)
Turns upward
Battery positive (+) → Terminal 14 (M+)
Battery negative (-) → Terminal 7 (MV)
Turns downward
Battery positive (+) → Terminal 13 (MH)
Battery negative (-) → Terminal 14 (M+)
Turns right
Battery positive (+) → Terminal 14 (M+)
Battery negative (-) → Terminal 13 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.
B450636C03
1.292,3.792 0.917,4.094 true 1.438,3.792 1.5,4.125 true 1.021,2.927 1.333,3.083 0.313,0.156 10 false *a 0.802,4.052 1.115,4.208 0.313,0.156 10 false + 1.5,4.156 1.813,4.313 0.313,0.156 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (+) - 9 (-) 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, check the outer mirror LH.


ii.

Connect a cable from the positive (+) battery terminal to terminal 8 and the negative (-) battery terminal to terminal 9, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror LH.



c.
B450637C03
1.354,1.344 0.938,1.74 true 1.875,1.354 2.198,1.75 true 0.302,0.198 0.615,0.354 0.313,0.156 10 false *a 0.896,1.719 1.198,1.906 0.302,0.188 10 false - 2.073,1.781 2.552,1.979 0.479,0.198 10 false BSL+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor)

NOTICE:

Do not apply a voltage of 6 V or higher.


i.

Check the operation of the blind spot monitor indicator.


ii.

Connect 4 dry-cell batteries (1.5 V each) in series.


iii.

Connect a positive (+) lead from the batteries to terminal 12 (BSL+) and a negative (-) lead to terminal 9 (-) and check that the blind spot monitor indicator comes on.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 12 (BSL+)
Battery negative (-) → Terminal 9 (-)
Blind spot monitor indicator comes on


If the result is not as specified, check the outer mirror LH.



d.
B450638C02
1.917,4 2.333,3.583 true 2.042,4.021 2.5,3.813 true 1.073,3.385 1.385,3.542 0.313,0.156 10 false *a 1.292,0.073 1.615,0.271 0.323,0.198 10 false (A) 0.948,1.01 1.271,1.208 0.323,0.198 10 false (B) 1.156,2.146 1.479,2.344 0.323,0.198 10 false (C) 1.646,2.427 1.969,2.625 0.323,0.198 10 false (D) 2.177,2.74 2.5,2.938 0.323,0.198 10 false (E) 2.396,3.479 2.719,3.635 0.323,0.156 10 false MR 2.563,3.708 2.885,3.865 0.323,0.156 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the retractable mirror. (w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87910 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (for LED Type Turn Signal Light)

a.
B458228C01
1.208,3.771 0.823,4.198 true 1.396,3.781 1.698,4.188 true 0.781,3.469 1.208,3.615 true 0.604,2.927 0.917,3.083 0.313,0.156 10 false *a 0.552,4.125 0.865,4.313 0.313,0.188 10 false MH 1.76,4.104 2.073,4.292 0.313,0.188 10 false M+ 0.521,3.365 0.833,3.552 0.313,0.188 10 false MV
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror surface.

i.

Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 10 (M+)
Turns upward
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 7 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)
Turns left
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.
B458229C01
1.656,3.594 2.208,3.042 true 1.656,3.771 2.156,4.177 true 0.667,2.969 0.979,3.125 0.313,0.156 10 false *a 2.26,2.958 2.573,3.115 0.313,0.156 10 false + 2.219,4.094 2.531,4.25 0.313,0.156 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (+) - 12 (-) 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, check the outer mirror RH.


ii.

Connect a cable from the positive (+) battery terminal to terminal 4 and negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror RH.



c.
B458226C02
1.594,1.323 1.219,1.792 true 2.323,1.125 2.667,0.917 true 0.219,0.188 0.531,0.344 0.313,0.156 10 false *a 1.177,1.781 1.49,1.938 0.313,0.156 10 false - 2.729,0.844 3.24,1.031 0.51,0.188 10 false BSR+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the blind spot monitor indicator.

NOTICE:

Do not apply a voltage of 6 V or higher.


i.

Check the operation of the blind spot monitor indicator.


ii.

Connect 4 dry-cell batteries (1.5 V each) in series.


iii.

Connect a positive (+) lead from the batteries to terminal 8 (BSR+) and a negative (-) lead to terminal 12 (-) and check that the blind spot monitor indicator comes on.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 8 (BSR+)
Battery negative (-) → Terminal 12 (-)
Blind spot monitor indicator comes on


If the result is not as specified, check the outer mirror RH.



d.
B458230C01
1.604,3.844 1.948,3.281 true 1.031,4.323 1.531,4.031 true 0.531,3.177 0.844,3.333 0.313,0.156 10 false *a 2.208,0.073 2.521,0.281 0.313,0.208 10 false (A) 2.531,1.125 2.844,1.333 0.313,0.208 10 false (B) 2.375,2.156 2.688,2.365 0.313,0.208 10 false (C) 1.771,2.438 2.083,2.646 0.313,0.208 10 false (D) 1.333,2.771 1.646,2.979 0.313,0.208 10 false (E) 2.01,3.177 2.323,3.333 0.313,0.156 10 false MR 0.781,4.26 1.094,4.417 0.313,0.156 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the retractable mirror. (w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 5 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 5 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 5 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 5 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 5 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.



Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (for Bulb Type Turn Signal Light)

a.
B450639C03
2.094,3.594 2.427,3.271 true 2.104,3.792 2.406,4.094 true 1.917,3.792 1.604,4.115 true 1.052,2.917 1.365,3.073 0.313,0.156 10 false *a 2.49,3.167 2.802,3.375 0.313,0.208 10 false MV 2.469,4.031 2.781,4.188 0.313,0.156 10 false M+ 1.354,4.083 1.667,4.24 0.313,0.156 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror surface.

i.

Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 7 (MV)
Battery negative (-) → Terminal 14 (M+)
Turns upward
Battery positive (+) → Terminal 14 (M+)
Battery negative (-) → Terminal 7 (MV)
Turns downward
Battery positive (+) → Terminal 13 (MH)
Battery negative (-) → Terminal 14 (M+)
Turns left
Battery positive (+) → Terminal 14 (M+)
Battery negative (-) → Terminal 13 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.
B450640C02
1.281,3.781 0.896,4.188 true 1.479,3.792 1.708,4.188 true 1.031,2.896 1.344,3.052 0.313,0.156 10 false *a 0.802,4.188 1.115,4.344 0.313,0.156 10 false + 1.74,4.208 2.052,4.365 0.313,0.156 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (+) - 9 (-) 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, check the outer mirror RH.


ii.

Connect a cable from the positive (+) battery terminal to terminal 8 and negative (-) battery terminal to terminal 9, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror RH.



c.
B450637C04
1.354,1.354 0.948,1.719 true 1.896,1.354 2.198,1.698 true 0.281,0.198 0.594,0.354 0.313,0.156 10 false *a 0.844,1.625 1.156,1.781 0.313,0.156 10 false - 2.25,1.635 2.74,1.844 0.49,0.208 10 false BSR+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor)

NOTICE:

Do not apply a voltage of 6 V or higher.


i.

Check the operation of the blind spot monitor indicator.


ii.

Connect 4 dry-cell batteries (1.5 V each) in series.


iii.

Connect a positive (+) lead from the batteries to terminal 12 (BSR+) and a negative (-) lead to terminal 9 (-) and check that the blind spot monitor indicator comes on.

OK:
Measurement Connection Specified Condition
Battery positive (+) → Terminal 12 (BSR+)
Battery negative (-) → Terminal 9 (-)
Blind spot monitor indicator comes on


If the result is not as specified, check the outer mirror RH.



d.
B450641C02
1.917,4 2.417,3.417 true 2.063,4.021 2.49,3.635 true 1.01,3.365 1.323,3.521 0.313,0.156 10 false *a 2.188,0.063 2.51,0.292 0.323,0.229 10 false (A) 2.448,0.948 2.771,1.177 0.323,0.229 10 false (B) 2.313,2.135 2.635,2.365 0.323,0.229 10 false (C) 1.792,2.448 2.115,2.677 0.323,0.229 10 false (D) 1.333,2.74 1.656,2.969 0.323,0.229 10 false (E) 2.469,3.313 2.781,3.469 0.313,0.156 10 false MR 2.563,3.573 2.875,3.729 0.313,0.156 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the retractable mirror. (w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 5 (MR)
Battery negative (-) → Terminal 6 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 6 (MF)
Battery negative (-) → Terminal 5 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.