Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR GLASS
RM32H0E _59 Vehicle Exterior _059645 MIRROR (EXT) _0292589 OUTER REAR VIEW MIRROR GLASS G

MIRROR (EXT)  OUTER REAR VIEW MIRROR GLASS  INSPECTION  


PROCEDURE

Hide 87961 1.INSPECT OUTER MIRROR LH (for LED Type Turn Signal Light)

a.
B458199C01
1.552,1.229 0.833,1.813 true 0.656,0.25 1.552,0.854 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.531,0.125 0.677,0.323 0.146,0.198 10 false 1 0.698,1.74 0.865,1.938 0.167,0.198 10 false 2
*a Component without harness connected
(Outer Mirror LH)


Check the resistance.

i.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, replace the outer mirror LH.



b.
B458200C01
0.385,0.542 0.698,0.698 0.313,0.156 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Check the operation of the outer rear view mirror indicator.

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
6 V battery positive (+) → Terminal 1
6 V battery negative (-) → Terminal 2
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror LH.



Hide 87931 2.INSPECT OUTER MIRROR RH (for LED Type Turn Signal Light)

a.
B458201C01
1.875,0.844 2.833,0.333 true 1.875,1.208 2.5,1.833 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 2.917,0.24 3.229,0.396 0.313,0.156 10 false 1 2.51,1.844 2.823,2 0.313,0.156 10 false 2
*a Component without harness connected
(Outer Mirror RH)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, replace the outer mirror RH.



b.
B458202C01
2.302,0.469 2.615,0.667 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Check the operation of the outer rear view mirror indicator.

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
6 V battery positive (+) → Terminal 1
6 V battery negative (-) → Terminal 2
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror RH.



Hide 87961 3.INSPECT OUTER MIRROR LH (for Bulb Type Turn Signal Light)

a.
B450647C02
1.469,0.677 2.104,0.25 true 2.146,0.979 2.76,0.479 true 0.031,0.042 0.219,0.229 0.188,0.188 10 true *a 2.167,0.156 2.354,0.344 0.188,0.188 10 false 1 2.823,0.396 3.01,0.583 0.188,0.188 10 false 2
*a Component without harness connected
(Outer Mirror LH)


Check the resistance.

i.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, replace the outer mirror LH.



b.
B450648C03
1.167,1.313 1.385,1.521 0.219,0.208 10 true *a
*a Component without harness connected
(Outer Mirror LH)


Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
6 V battery positive (+) → Terminal 1
6 V battery negative (-) → Terminal 2
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror LH.



Hide 87931 4.INSPECT OUTER MIRROR RH (for Bulb Type Turn Signal Light)

a.
B450649C03
1.958,0.677 1.333,0.25 true 0.708,0.531 1.281,0.979 true 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 1.198,0.146 1.427,0.354 0.229,0.208 10 false 1 0.563,0.427 0.792,0.635 0.229,0.208 10 false 2
*a Component without harness connected
(Outer Mirror RH)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, replace the outer mirror RH.



b.
B450650C03
1.198,1.271 1.406,1.458 0.208,0.188 10 true *a
*a Component without harness connected
(Outer Mirror RH)


Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
6 V battery positive (+) → Terminal 1
6 V battery negative (-) → Terminal 2
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror RH.