Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM32H0E _58 Vehicle Interior _059647 DOOR LOCK _0292599 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69040A 1.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

a.
B366803C10
1.208,3.646 0.656,3.552 true 1.198,3.917 0.698,4.115 true 1.417,3.979 1.073,4.354 true 1.604,3.979 1.646,4.375 true 1.813,3.979 2.115,4.344 true 2.208,3.688 2.635,3.583 true 0.844,2.969 1.156,3.125 0.313,0.156 10 false *a 2.104,2.24 2.417,2.396 0.313,0.156 10 false *b 1.625,2.583 1.938,2.74 0.313,0.156 10 false *c 0.531,3.458 0.844,3.615 0.313,0.156 10 false L 0.479,4.052 0.792,4.208 0.313,0.156 10 false UL 1.01,4.385 1.323,4.542 0.313,0.156 10 false L 1.5,4.396 1.938,4.594 0.438,0.198 10 false LSSR 2.083,4.375 2.396,4.531 0.313,0.156 10 false E 2.667,3.5 2.979,3.656 0.313,0.156 10 false UL
*a Component without harness connected (Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the door lock motor operation (for Driver Side).

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 9 (L)
Battery negative (-) → 10 (UL)
Set
Battery positive (+) → 10 (UL)
Battery negative (-) → 9 (L)
Unset


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly LH.



b.

Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω
9 (L) - 10 (UL) Unset 10 kΩ or higher
9 (L) - 10 (UL) Set Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly LH.



c.
B402290C05
1.208,3.969 0.885,4.344 true 1.438,4 1.385,4.344 true 1.802,3.99 2.031,4.333 true 0.75,2.938 1.063,3.094 0.313,0.156 10 false *a 2.073,0.74 2.385,0.896 0.313,0.156 10 false *b 1.885,1.292 2.198,1.448 0.313,0.156 10 false *c 2.177,1.875 2.49,2.031 0.313,0.156 10 false *d 0.781,4.354 1.094,4.51 0.313,0.156 10 false UL 1.323,4.365 1.635,4.521 0.313,0.156 10 false L 1.99,4.365 2.302,4.521 0.313,0.156 10 false E
*a Component without harness connected (Front Door Lock with Motor Assembly LH)
*b Unlock
*c Off
*d Lock


Check the resistance of the lock and unlock switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Held to lock side Below 1 Ω
9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher
10 (UL) - 7 (E) Held to unlock side Below 1 Ω
10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly LH.



d.
B366803C11
1.219,3.656 0.75,3.573 true 2.677,3.573 2.208,3.698 true 2.125,4.313 1.813,3.99 true 1.396,4.323 1.594,4 true 0.844,2.969 1.156,3.125 0.313,0.156 10 false *a 2.104,2.24 2.417,2.396 0.313,0.156 10 false *b 1.625,2.583 1.938,2.74 0.313,0.156 10 false *c 0.625,3.479 0.938,3.635 0.313,0.156 10 false L 1.208,4.333 1.646,4.51 0.438,0.177 10 false LSSR 2.104,4.354 2.417,4.51 0.313,0.156 10 false E 2.719,3.5 3.031,3.656 0.313,0.156 10 false UL
*a Component without harness connected (Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor (for Front Passenger Side).

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the front door lock with motor assembly LH.



e.

Check the operation of the door unlock detection switch (for Front Passenger Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly LH.



Hide 69030A 2.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

a.
B402291C03
1.219,3.656 0.781,3.604 true 2.625,3.604 2.188,3.667 true 2.042,4.292 1.833,3.979 true 1.375,4.281 1.583,3.969 true 0.698,3.042 1.01,3.198 0.313,0.156 10 false *a 1.177,2.188 1.49,2.344 0.313,0.156 10 false *b 1.625,2.635 1.938,2.792 0.313,0.156 10 false *c 0.635,3.51 0.885,3.698 0.25,0.188 10 false L 1.302,4.323 1.552,4.51 0.25,0.188 10 false E 2.677,3.5 2.99,3.677 0.313,0.177 10 false UL 1.896,4.313 2.333,4.51 0.438,0.198 10 false LSSR
*a Component without harness connected (Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor (for Front Passenger Side).

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Locks
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlocks


If the result is not as specified, replace the front door lock with motor assembly RH.



b.

Check the operation of the door unlock detection switch (for Front Passenger Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly RH.



c.
B366802C08
1.208,3.698 0.792,3.604 true 2.604,3.625 2.177,3.708 true 1.563,3.99 1.135,4.333 true 1.771,3.99 1.656,4.333 true 2,3.99 2.104,4.333 true 2.198,3.979 2.458,4.354 true 0.854,2.969 1.167,3.125 0.313,0.156 10 false *a 1.198,2.229 1.51,2.385 0.313,0.156 10 false *b 1.583,2.583 1.896,2.74 0.313,0.156 10 false *c 0.646,3.531 0.958,3.688 0.313,0.156 10 false L 1.073,4.365 1.385,4.521 0.313,0.156 10 false E 1.458,4.375 1.958,4.583 0.5,0.208 10 false LSSR 2.396,4.375 2.708,4.531 0.313,0.156 10 false UL 2.115,4.354 2.427,4.51 0.313,0.156 10 false L 2.667,3.531 2.979,3.688 0.313,0.156 10 false UL
*a Component without harness connected (Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the door lock motor operation (for Driver Side).

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Battery Connection Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Locks
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlocks
Battery positive (+) → 6 (L)
Battery negative (-) → 5 (UL)
Sets
Battery positive (+) → 5 (UL)
Battery negative (-) → 6 (L)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly RH.



d.

Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω
5 (UL) - 6 (L) Unset 10 kΩ or higher
5 (UL) - 6 (L) Set Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly RH.



e.
B366804C07
1.563,3.979 1.344,4.375 true 2,3.99 2.167,4.396 true 2.177,3.979 2.49,4.333 true 0.875,2.958 1.188,3.115 0.313,0.156 10 false *a 1.177,0.74 1.49,0.896 0.313,0.156 10 false *b 1.365,1.302 1.677,1.458 0.313,0.156 10 false *c 1.104,1.833 1.417,1.99 0.313,0.156 10 false *d 1.281,4.417 1.594,4.573 0.313,0.156 10 false E 2.563,4.281 2.875,4.438 0.313,0.156 10 false UL 2.146,4.417 2.458,4.573 0.313,0.156 10 false L
*a Component without harness connected (Front Door Lock with Motor Assembly RH)
*b Unlock
*c Off
*d Lock


Check the resistance of the lock and unlock switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly RH.



Hide 69040A 3.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

a.
B450671C02
1.521,3.76 1.125,3.115 true 1.875,3.76 2.24,3.167 true 2.167,3.771 2.594,3.479 true 2.219,4.073 2.667,4.26 true 2,4.135 2.24,4.406 true 1.792,4.125 1.75,4.406 true 1.573,4.125 1.354,4.406 true 0.75,3.688 1.219,3.802 true 0.906,3.042 1.219,3.198 0.313,0.156 10 false UL 2.531,2.385 2.844,2.542 0.313,0.156 10 false *b 2.115,2.635 2.427,2.792 0.313,0.156 10 false *c 0.479,2.917 0.792,3.073 0.313,0.156 10 false *a 2.313,3.063 2.625,3.219 0.313,0.156 10 false DL 0.604,3.594 0.917,3.75 0.313,0.156 10 false L 1.115,4.417 1.552,4.615 0.438,0.198 10 false LSSR 1.708,4.417 2.021,4.573 0.313,0.156 10 false E 2.073,4.427 2.531,4.604 0.458,0.177 10 false DLSR 2.729,4.188 3.042,4.344 0.313,0.156 10 false E 2.656,3.385 3.146,3.573 0.49,0.188 10 false UNDL
*a Component without harness connected (Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the front door lock motor (for Driver Side).

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Battery Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 3 (UL)
Locks
Battery positive (+) → Terminal 3 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks
Battery positive (+) → Terminal 2 (DL)
Battery negative (-) → Terminal 1 (UNDL)
Sets
Battery positive (+) → Terminal 1 (UNDL)
Battery negative (-) → Terminal 2 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly LH.



b.

Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (LSSR) - 7 (E) Locked 10 kΩ or higher
8 (LSSR) - 7 (E) Unlocked Below 1 Ω
6 (DLSR) - 5 (E) Unset 10 kΩ or higher
6 (DLSR) - 5 (E) Set Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly LH.



c.
B450674C02
1.208,3.771 0.729,4.104 true 1.417,3.792 1.292,4.198 true 1.771,3.802 1.854,4.188 true 0.385,2.698 0.698,2.854 0.313,0.156 10 false *a 1.99,1.573 2.302,1.729 0.313,0.156 10 false *b 1.885,0.458 2.198,0.615 0.313,0.156 10 false *c 0.5,4.031 0.813,4.188 0.313,0.156 10 false UL 1.823,4.229 2.146,4.417 0.323,0.188 10 false E 1.25,4.24 1.573,4.427 0.323,0.188 10 false L
*a Component without harness connected (Front Door Lock with Motor Assembly LH)
*b Lock
*c Unlock


Check the operation of the door key lock and unlock switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Held to lock side Below 1 Ω
9 (L) - 7 (E) Neutral or held to unlock side 10 kΩ or higher
10 (UL) - 7 (E) Held to unlock side Below 1 Ω
10 (UL) - 7 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly LH.



d.
B450671C03
1.521,3.76 1.083,3.115 true 1.906,3.76 2.271,3.146 true 2.177,3.781 2.594,3.688 true 2.198,4.104 2.688,4.292 true 2.01,4.135 2.229,4.417 true 1.823,4.115 1.781,4.396 true 1.552,4.125 1.323,4.396 true 0.76,3.75 1.198,3.792 true 0.333,2.979 0.646,3.135 0.313,0.156 10 false *a 2.531,2.385 2.844,2.542 0.313,0.156 10 false *b 2.115,2.635 2.427,2.792 0.313,0.156 10 false *c 0.885,3.052 1.198,3.208 0.313,0.156 10 false UL 2.344,3.063 2.656,3.219 0.313,0.156 10 false DL 2.656,3.615 3.219,3.813 0.563,0.198 10 false UNDL 2.729,4.219 3.042,4.375 0.313,0.156 10 false E 2.042,4.438 2.521,4.625 0.479,0.188 10 false DLSR 1.719,4.438 2.031,4.594 0.313,0.156 10 false E 1.135,4.438 1.594,4.594 0.458,0.156 10 false LSSR 0.615,3.667 0.927,3.823 0.313,0.156 10 false L
*a Component without harness connected (Front Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the front door lock motor (for Front Passenger Side).

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Battery Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 3 (UL)
Locks
Battery positive (+) → Terminal 3 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocks
Battery positive (+) → Terminal 2 (DL)
Battery negative (-) → Terminal 1 (UNDL)
Sets
Battery positive (+) → Terminal 1 (UNDL)
Battery negative (-) → Terminal 2 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly LH.



e.

Check the operation of the door unlock detection switch and double lock position switch (for Front Passenger Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (LSSR) - 7 (E) Locked 10 kΩ or higher
8 (LSSR) - 7 (E) Unlocked Below 1 Ω
6 (DLSR) - 5 (E) Unset 10 kΩ or higher
6 (DLSR) - 5 (E) Set Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly LH.



Hide 69030A 4.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

a.
B450672C02
1.531,3.75 1.25,3.125 true 1.823,3.74 2.25,3.104 true 2.156,3.771 2.531,3.448 true 1.823,4.125 2.177,4.417 true 1.635,4.125 1.802,4.417 true 1.438,4.146 1.406,4.427 true 1.219,4.125 0.938,4.396 true 1.219,3.823 0.813,3.708 true 0.417,2.969 0.729,3.125 0.313,0.156 10 false *a 0.792,2.375 1.104,2.531 0.313,0.156 10 false *b 1.219,2.646 1.531,2.802 0.313,0.156 10 false *c 0.844,3.063 1.354,3.24 0.51,0.177 10 false UNDL 2.313,3.01 2.521,3.198 0.208,0.188 10 false L 2.604,3.375 2.969,3.542 0.365,0.167 10 false UL 2.052,4.448 2.563,4.625 0.51,0.177 10 false LSSR 1.771,4.448 2.146,4.604 0.375,0.156 10 false E 1.219,4.438 1.729,4.615 0.51,0.177 10 false DLSR 0.875,4.427 1.146,4.604 0.271,0.177 10 false E 0.594,3.635 0.906,3.823 0.313,0.188 10 false DL
*a Component without harness connected (Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the front door lock motor (for Front Passenger Side).

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Battery Connection Result
Battery positive (+) → Terminal 2 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 2 (L)
Unlocks
Battery positive (+) → Terminal 4 (DL)
Battery negative (-) → Terminal 3 (UNDL)
Sets
Battery positive (+) → Terminal 3 (UNDL)
Battery negative (-) → Terminal 4 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly RH.



b.

Check the operation of the door unlock detection switch and double lock position switch (for Front Passenger Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω
9 (DLSR) - 10 (E) Unset 10 kΩ or higher
9 (DLSR) - 10 (E) Set Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly RH.



c.
B450672C03
1.573,3.76 1.292,3.073 true 1.865,3.75 2.271,3.073 true 2.177,3.823 2.583,3.635 true 1.802,4.135 2.156,4.406 true 1.635,4.135 1.719,4.406 true 1.438,4.135 1.323,4.396 true 1.188,4.125 0.896,4.385 true 1.198,3.854 0.792,3.708 true 0.385,2.938 0.698,3.094 0.313,0.156 10 false *a 0.792,2.375 1.104,2.531 0.313,0.156 10 false *b 1.219,2.646 1.531,2.802 0.313,0.156 10 false *c 0.906,3.021 1.375,3.188 0.469,0.167 10 false UNDL 0.573,3.635 0.865,3.802 0.292,0.167 10 false DL 0.833,4.406 1.063,4.573 0.229,0.167 10 false E 1.135,4.417 1.604,4.583 0.469,0.167 10 false DLSR 2.021,4.438 2.49,4.604 0.469,0.167 10 false LSSR 1.667,4.438 1.948,4.615 0.281,0.177 10 false E 2.635,3.542 3.104,3.708 0.469,0.167 10 false UL 2.344,2.99 2.573,3.167 0.229,0.177 10 false L
*a Component without harness connected (Front Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the front door lock motor (for Driver Side).

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Battery Connection Result
Battery positive (+) → Terminal 2 (L)
Battery negative (-) → Terminal 1 (UL)
Locks
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 2 (L)
Unlocks
Battery positive (+) → Terminal 4 (DL)
Battery negative (-) → Terminal 3 (UNDL)
Sets
Battery positive (+) → Terminal 3 (UNDL)
Battery negative (-) → Terminal 4 (DL)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock with motor assembly RH.



d.

Check the operation of the door unlock detection switch and double lock position switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω
9 (DLSR) - 10 (E) Unset 10 kΩ or higher
9 (DLSR) - 10 (E) Set Below 1 Ω


If the result is not as specified, replace the front door lock with motor assembly RH.



e.
B450673C02
1.375,4.156 1.594,3.771 true 2.156,4.177 1.969,3.792 true 2.615,4.01 2.177,3.76 true 0.49,2.667 0.802,2.823 0.313,0.156 10 false *a 1.146,1.563 1.458,1.719 0.313,0.156 10 false *b 1.292,0.448 1.604,0.604 0.313,0.156 10 false *c 1.313,4.188 1.625,4.344 0.313,0.156 10 false E 2.667,3.948 2.979,4.104 0.313,0.156 10 false UL 2.115,4.188 2.427,4.344 0.313,0.156 10 false L
*a Component without harness connected (Front Door Lock with Motor Assembly RH)
*b Lock
*c Unlock


Check the operation of the door key lock and unlock switch (for Driver Side).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Held to lock side Below 1 Ω
6 (L) - 8 (E) Neutral or held to unlock side 10 kΩ or higher
5 (UL) - 8 (E) Held to unlock side Below 1 Ω
5 (UL) - 8 (E) Neutral or held to lock side 10 kΩ or higher


If the result is not as specified, replace the front door lock with motor assembly RH.