Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensors. Each speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) converts the wheel speed signals into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.
Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to the speed signal.
A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P050031 | Vehicle Speed Sensor "A" No Signal | While vehicle being driven, no vehicle speed sensor signal transmitted to ECM for 5.25 seconds (2 trip detection logic). | ·
Open or short in speed signal circuit ·
Combination meter assembly ·
ECM |
Does not come on | DTC stored | SAE Code:
P0500 |
If there is no speed signal from the combination meter assembly even though the ECM determines that the vehicle is being driven, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then stores a DTC.
Refer to Speed Signal Circuit.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the ignition switch to ON and wait for 3 seconds or more.
Drive the vehicle at 10 km/h (6.21 mph) or more for 5 seconds or more.
Check for DTCs again.
Click hereDrivetrain>EC6A (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.
The vehicle speed sensor is operating normally if the speedometer reading is normal.
If the speedometer does not operate, check it by following the diagnostic procedure for a malfunction of the speedometer.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.
| Tester Display |
|---|
| Vehicle Speed |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the wheel speed sensors. ·
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. |
Drive the vehicle.
According to the display on the GTS, read the Data List.
The values displayed on the GTS and speedometer are equal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F4 combination meter assembly connector.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F4-6 (+S) - A38-44 (SPD) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Proceed to Speed Signal Circuit in Meter/Gauge System.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle for 6 seconds or more.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs.
If no DTCs (no pending DTCs) are output, the repair has been successfully completed.
| Proceed to |
|---|
| NEXT |
NEXT