Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › TRANSFER ASSEMBLY
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0292792 TRANSFER ASSEMBLY A

GF1A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Steps 9 to 16 are temporary reassembly procedures for adjustment purposes.


PROCEDURE

Hide 36128B 1.INSTALL BREATHER OIL DEFLECTOR

C284183

a.

Install a new breather oil deflector to the transfer case with the 2 bolts.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 41319 2.INSTALL TRANSFER RING GEAR MOUNTING CASE

C130226N08
0.906,0.729 0.75,0.417 0.75,0.417 0.667,0.417 true 1.031,1.302 1.24,1.833 1.24,1.833 1.333,1.833 true 0.365,0.354 0.698,0.5 0.333,0.146 10 SST 1.365,1.75 1.677,1.917 0.313,0.167 10 SST

a.

Using SST and a press, press the transfer ring gear mounting case into the transfer ring gear.

SST
09316-12010  
09950-60010  (09951-00560)

NOTICE:

Do not put stress on the teeth of the transfer ring gear.



Hide 36212L 3.INSTALL SHAFT SNAP RING

C109636

a.

Using a snap ring expander, install a new shaft snap ring.


Hide 41301H 4.INSTALL RING GEAR MOUNTING CASE BEARING RH

a.
C156148C03
1.333,0.667 1.167,1.469 true 1.271,1.563 1.271,2.167 1.271,2.167 1.396,2.167 true 0.333,1.917 0.417,1.917 0.417,1.917 0.594,1.469 true 1,1.333 1.333,0.667 true 0.917,1.083 1.333,0.667 1.333,0.667 1.417,0.667 true 1.49,0.583 2,0.844 0.51,0.26 10 false SST 1.427,2.094 1.833,2.333 0.406,0.24 10 false *1 0.135,1.833 0.333,2 0.198,0.167 10 false *2
*1 No. 2 Transfer Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing RH (Outer Race)


Install a new No. 2 transfer ring gear mounting case washer to the No. 1 transfer case cover.

HINT:

Install a No. 2 transfer ring gear mounting case washer with the same thickness as the one before the disassembly.



b.

Using SST and a press, press the ring gear mounting case bearing RH (outer race) into the No. 1 transfer case cover.

SST
09950-60020  (09951-00750, 09952-06010)
09950-70010  (09951-07150)
09951-00850  

NOTICE:
·

Press in the ring gear mounting case bearing RH (outer race) and No. 2 transfer ring gear mounting case washer until they fit to the edge.

·

Do not put stress on the rolling contact surface of the ring gear mounting case bearing RH (outer race).




c.
C130227N08
0.75,0.333 0.833,0.333 0.833,0.333 1.083,0.583 true 1.083,1.688 1.5,2 1.5,2 1.583,2 true 0.417,0.25 0.875,0.448 0.458,0.198 10 SST 1.625,1.917 2.083,2.115 0.458,0.198 10 SST

Using SST and a press, press the ring gear mounting case bearing RH (inner race) into the transfer ring gear mounting case.

SST
09950-60010  (09951-00440, 09951-00650)

NOTICE:

Do not deform the ring gear mounting case bearing RH (inner race) cage.


HINT:

When reusing the ring gear mounting case bearing RH, coat the ring gear mounting case bearing RH with Toyota Genuine Differential gear oil LT SAE 75W-85 API GL-5 or equivalent.



Hide 41301H 5.INSTALL RING GEAR MOUNTING CASE BEARING LH

a.
C156149C03
1.052,1.542 1.052,2.146 1.052,2.146 1.135,2.146 true 0.656,1.479 0.406,2.063 0.406,2.063 0.323,2.063 true 1.25,0.917 0.917,1.333 true 1.25,0.917 1,1.417 true 1.333,0.917 1.25,0.917 1.25,0.917 0.917,1.167 true 1.188,2.063 1.656,2.302 0.469,0.24 10 *1 0.167,1.99 0.563,2.24 0.396,0.25 10 *2 1.427,0.833 2,1.052 0.573,0.219 10 SST
*1 No. 1 Ring Gear Mounting Case Washer
*2 Ring Gear Mounting Case Bearing LH (Outer Race)


Install a new No. 1 ring gear mounting case washer to the transfer case.

HINT:

Install a No. 1 ring gear mounting case washer with the same thickness as the one before the disassembly.



b.

Using SST and a press, press the ring gear mounting case bearing LH (outer race) into the transfer case.

SST
09950-60010  (09951-00570, 09951-00650, 09952-06010)
09950-70010  (09951-07150)

NOTICE:
·

Press in the ring gear mounting case bearing LH (outer race) and No. 1 ring gear mounting case washer until they fit to the edge.

·

Do not put stress on the rolling contact surface of the ring gear mounting case bearing LH (outer race).




c.
C130228N08
2.917,0.333 2.833,0.333 2.833,0.333 2.667,0.531 true 3,1.25 2.917,1.25 2.917,1.25 2.833,1.5 true 2.948,0.271 3.333,0.5 0.385,0.229 10 SST 3.031,1.177 3.365,1.333 0.333,0.156 10 SST

Using SST and a press, press the ring gear mounting case bearing LH (inner race) into the transfer ring gear mounting case.

SST
09336-16010  
09950-60010  (09951-00560)

NOTICE:

Do not deform the ring gear mounting case bearing LH (inner race) cage.


HINT:

When reusing the ring gear mounting case bearing LH, coat the ring gear mounting case bearing LH with Toyota Genuine Differential gear oil LT SAE 75W-85 API GL-5 or equivalent.



Hide 36275E 6.INSTALL TRANSFER OUTPUT SHAFT WASHER

C110759

a.

Install the transfer output shaft washer to the transfer driven pinion.


Hide 41201K 7.INSTALL FRONT TRANSFER DRIVEN PINION BEARING

C291235N01
0.969,0.448 1.26,0.292 1.26,0.292 1.021,0.729 true 0.5,1.74 0.656,1.74 0.656,1.74 0.813,1.625 true 1.365,0.208 1.823,0.406 0.458,0.198 10 false SST 0.198,1.677 0.656,1.875 0.458,0.198 10 false SST

a.

Using SST and a press, press the front transfer driven pinion bearing into the transfer driven pinion.

SST
09950-60010  (09951-00440)
09950-60020  (09951-00750)
09950-70010  (09951-07150)

NOTICE:

Do not apply stress to any parts of the front transfer driven pinion bearing inner race or transfer driven pinion other than the flat surfaces.



Hide 33325A 8.INSTALL REAR TRANSFER OUTPUT SHAFT DUST DEFLECTOR

a.
C368149E01
3.083,2.063 2.917,2.063 2.917,2.063 2.844,1.99 false 2.896,0.833 3.052,0.281 false 3.094,1.979 3.385,2.167 0.292,0.188 10 false SST 2.927,0.125 3.219,0.313 0.292,0.188 10 false SST

Using SST and a press, press a new rear transfer output shaft dust deflector into the rear transfer output shaft sub-assembly.

SST
09316-12010  
09950-60020  (09951-00680)

NOTICE:

The rear transfer output shaft dust deflector should be installed completely.



Hide 9.INSTALL TRANSFER DRIVEN PINION

a.
C368150N01
2.813,1.635 2.969,1.063 false 2.698,3.365 2.958,3.927 false 2.865,0.917 3.323,1.115 0.458,0.198 10 false SST 2.844,3.969 3.302,4.167 0.458,0.198 10 false SST

Using SST and a press, press the rear transfer output shaft sub-assembly into the transfer driven pinion.

SST
09506-30012  
09950-60020  (09951-00680)

NOTICE:

Do not apply stress to any parts of the transfer output shaft flange or transfer driven pinion other than the flat surfaces.



b.
C340162

Secure the rear transfer output shaft sub-assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Using a 30 mm socket wrench, install a new transfer gear nut to the rear transfer output shaft sub-assembly.

Torque:
360 N*m (3671 kgf*cm, 266 ft.*lbf)


Hide 36202 10.INSTALL REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

a.
C375282C01
2.354,1.708 2.708,1.479 true 2.156,1.698 2.469,1.896 0.313,0.198 10 false *1
*1 O-ring


Install a new O-ring to the front transfer driven pinion bearing.

NOTICE:
·

Do not scratch or twist the O-ring.

·

Firmly install the O-ring into the groove of the front transfer driven pinion bearing.




b.
C375278

Install the rear transfer output shaft sub-assembly to the transfer case with the 5 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Do not scratch or twist the O-ring.



Hide 11.INSPECT DRIVEN PINION PRELOAD

C375271C01
1.958,0.531 2.24,0.531 false 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 2.302,0.427 2.615,0.625 0.313,0.198 10 false *1
*1 Nut
*a 90°


a.

Install a nut to the stud bolt.

HINT:

Use a nut that is used for installing the propeller shaft.



b.

Using a torque wrench, check the driven pinion preload (starting torque) of the driven pinion.

Preload (at Starting):
Item Driven Pinion Preload
New bearing
(with anti-rust oil)
0.39 to 2.21 N*m (3.98 to 22.53 kgf*cm, 3.46 to 19.55 in.*lbf)
Reused bearing
(when coated with gear oil)
0.39 to 2.21 N*m (3.98 to 22.53 kgf*cm, 3.46 to 19.55 in.*lbf)


NOTICE:

Measure the preload after rotating the bearing several times in the forward and backward directions to make sure the bearing is operating correctly.


HINT:

Install the torque wrench as shown in the illustration.



Hide 12.INSTALL TRANSFER RING GEAR

C110563

a.

Uniformly apply a light coat of Prussian Blue on both sides of the transfer ring gear teeth.


b.
C375275

Install the transfer ring gear to the transfer case.


Hide 36121 13.INSTALL NO. 1 TRANSFER CASE COVER

a.
C375273

Install the No. 1 transfer case cover to the transfer case with the 8 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 14.ADJUST RING GEAR BACKLASH

a.
C158062

Insert a dial indicator into the No. 2 transfer case plug hole, and place it perpendicular to the edge of a transfer ring gear tooth.


b.

While securing the rear transfer output shaft sub-assembly by hand, rotate the transfer ring gear mounting case forward and backward by hand and measure the backlash of the transfer ring gear and transfer driven pinion.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


NOTICE:

Measure the ring gear at 3 or more locations.



c.

If the result is not within the specified range, select a No. 1 ring gear mounting case washer (for backlash adjustment) and a No. 2 transfer ring gear mounting case washer (for preload adjustment) from the table below and reinstall them to bring the result within the specified range.

HINT:
·

If the backlash is small, select a thick washer for the No. 1 ring gear mounting case washer (for backlash adjustment) and a thin washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).

·

If the backlash is large, select a thin washer for the No. 1 ring gear mounting case washer (for backlash adjustment) and a thick washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).



No. 1 Ring Gear Mounting Case Washer (for backlash adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36265-52010 1.97 mm (0.0776 in.) A0 36265-52210 2.37 mm (0.0933 in.) C0
36265-52020 1.99 mm (0.0783 in.) A1 36265-52220 2.39 mm (0.0941 in.) C1
36265-52030 2.01 mm (0.0791 in.) A2 36265-52230 2.41 mm (0.0949 in.) C2
36265-52040 2.03 mm (0.0799 in.) A3 36265-52240 2.43 mm (0.0957 in.) C3
36265-52050 2.05 mm (0.0807 in.) A4 36265-52250 2.45 mm (0.0965 in.) C4
36265-52060 2.07 mm (0.0815 in.) A5 36265-52260 2.47 mm (0.0972 in.) C5
36265-52070 2.09 mm (0.0823 in.) A6 36265-52270 2.49 mm (0.0980 in.) C6
36265-52080 2.11 mm (0.0831 in.) A7 36265-52280 2.51 mm (0.0988 in.) C7
36265-52090 2.13 mm (0.0839 in.) A8 36265-52290 2.53 mm (0.0996 in.) C8
36265-52100 2.15 mm (0.0846 in.) A9 36265-52300 2.55 mm (0.1004 in.) C9
36265-52110 2.17 mm (0.0854 in.) B0 36265-52310 2.57 mm (0.1012 in.) D0
36265-52120 2.19 mm (0.0862 in.) B1 36265-52320 2.59 mm (0.1020 in.) D1
36265-52130 2.21 mm (0.0870 in.) B2 36265-52330 2.61 mm (0.1028 in.) D2
36265-52140 2.23 mm (0.0878 in.) B3 36265-52340 2.63 mm (0.1035 in.) D3
36265-52150 2.25 mm (0.0886 in.) B4 36265-52350 2.65 mm (0.1043 in.) D4
36265-52160 2.27 mm (0.0894 in.) B5 36265-52360 2.67 mm (0.1051 in.) D5
36265-52170 2.29 mm (0.0902 in.) B6 36265-52370 2.69 mm (0.1059 in.) D6
36265-52180 2.31 mm (0.0909 in.) B7 36265-52380 2.71 mm (0.1067 in.) D7
36265-52190 2.33 mm (0.0917 in.) B8 36265-52390 2.73 mm (0.1075 in.) D8
36265-52200 2.35 mm (0.0925 in.) B9 36265-52400 2.75 mm (0.1083 in.) D9


No. 2 Transfer Ring Gear Mounting Case Washer (for preload adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36266-52010 1.18 mm (0.0465 in.) A0 36266-52230 1.62 mm (0.0638 in.) C2
36266-52020 1.20 mm (0.0472 in.) A1 36266-52240 1.64 mm (0.0646 in.) C3
36266-52030 1.22 mm (0.0480 in.) A2 36266-52250 1.66 mm (0.0654 in.) C4
36266-52040 1.24 mm (0.0488 in.) A3 36266-52260 1.68 mm (0.0661 in.) C5
36266-52050 1.26 mm (0.0496 in.) A4 36266-52270 1.70 mm (0.0669 in.) C6
36266-52060 1.28 mm (0.0504 in.) A5 36266-52280 1.72 mm (0.0677 in.) C7
36266-52070 1.30 mm (0.0512 in.) A6 36266-52290 1.74 mm (0.0685 in.) C8
36266-52080 1.32 mm (0.0520 in.) A7 36266-52300 1.76 mm (0.0693 in.) C9
36266-52090 1.34 mm (0.0528 in.) A8 36266-52310 1.78 mm (0.0701 in.) D0
36266-52100 1.36 mm (0.0535 in.) A9 36266-52320 1.80 mm (0.0709 in.) D1
36266-52110 1.38 mm (0.0543 in.) B0 36266-52330 1.82 mm (0.0717 in.) D2
36266-52120 1.40 mm (0.0551 in.) B1 36266-52340 1.84 mm (0.0724 in.) D3
36266-52130 1.42 mm (0.0559 in.) B2 36266-52350 1.86 mm (0.0732 in.) D4
36266-52140 1.44 mm (0.0567 in.) B3 36266-52360 1.88 mm (0.0740 in.) D5
36266-52150 1.46 mm (0.0575 in.) B4 36266-52370 1.90 mm (0.0748 in.) D6
36266-52160 1.48 mm (0.0583 in.) B5 36266-52380 1.92 mm (0.0756 in.) D7
36266-52170 1.50 mm (0.0591 in.) B6 36266-52390 1.94 mm (0.0764 in.) D8
36266-52180 1.52 mm (0.0598 in.) B7 36266-52400 1.96 mm (0.0772 in.) D9
36266-52190 1.54 mm (0.0606 in.) B8 36266-52410 1.98 mm (0.0780 in.) E0
36266-52200 1.56 mm (0.0614 in.) B9 36266-52420 2.00 mm (0.0787 in.) E1
36266-52210 1.58 mm (0.0622 in.) C0 36266-52430 2.02 mm (0.0795 in.) E2
36266-52220 1.60 mm (0.0630 in.) C1 - - -



Hide 15.ADJUST TOTAL PRELOAD

a.
C375271C01
1.958,0.531 2.24,0.531 false 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 2.302,0.427 2.615,0.625 0.313,0.198 10 false *1
*1 Nut
*a 90°


Install a nut to the stud bolt.

HINT:

Use a nut that is used for installing the propeller shaft.



b.

Using a torque wrench, measure the total preload (starting torque) with the teeth of the driven pinion and ring gear in contact.

Total preload (starting torque):
Item Specified Condition
New bearing (with anti-rust oil) Driven pinion preload + 0.31 to 0.81 N*m (3.17 to 8.25 kgf*cm, 2.75 to 7.16 in.*lbf)
Reused bearing (when coated with gear oil) Driven pinion preload + 0.48 to 0.64 N*m (4.90 to 6.52 kgf*cm, 4.25 to 5.66 in.*lbf)


NOTICE:

Measure the preload after rotating the bearing several times in the forward and backward directions to make sure the bearing is operating correctly.


HINT:

Install the torque wrench as shown in the illustration.



c.

If the result is not within the specified range, select a No. 2 transfer ring gear mounting case washer (for preload adjustment) from the table below and reinstall it to bring the result within the specified range.

HINT:
·

If the preload is small, select a thick washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).

·

If the preload is large, select a thin washer for the No. 2 transfer ring gear mounting case washer (for preload adjustment).



No. 2 Transfer Ring Gear Mounting Case Washer (for preload adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36266-52010 1.18 mm (0.0465 in.) A0 36266-52230 1.62 mm (0.0638 in.) C2
36266-52020 1.20 mm (0.0472 in.) A1 36266-52240 1.64 mm (0.0646 in.) C3
36266-52030 1.22 mm (0.0480 in.) A2 36266-52250 1.66 mm (0.0654 in.) C4
36266-52040 1.24 mm (0.0488 in.) A3 36266-52260 1.68 mm (0.0661 in.) C5
36266-52050 1.26 mm (0.0496 in.) A4 36266-52270 1.70 mm (0.0669 in.) C6
36266-52060 1.28 mm (0.0504 in.) A5 36266-52280 1.72 mm (0.0677 in.) C7
36266-52070 1.30 mm (0.0512 in.) A6 36266-52290 1.74 mm (0.0685 in.) C8
36266-52080 1.32 mm (0.0520 in.) A7 36266-52300 1.76 mm (0.0693 in.) C9
36266-52090 1.34 mm (0.0528 in.) A8 36266-52310 1.78 mm (0.0701 in.) D0
36266-52100 1.36 mm (0.0535 in.) A9 36266-52320 1.80 mm (0.0709 in.) D1
36266-52110 1.38 mm (0.0543 in.) B0 36266-52330 1.82 mm (0.0717 in.) D2
36266-52120 1.40 mm (0.0551 in.) B1 36266-52340 1.84 mm (0.0724 in.) D3
36266-52130 1.42 mm (0.0559 in.) B2 36266-52350 1.86 mm (0.0732 in.) D4
36266-52140 1.44 mm (0.0567 in.) B3 36266-52360 1.88 mm (0.0740 in.) D5
36266-52150 1.46 mm (0.0575 in.) B4 36266-52370 1.90 mm (0.0748 in.) D6
36266-52160 1.48 mm (0.0583 in.) B5 36266-52380 1.92 mm (0.0756 in.) D7
36266-52170 1.50 mm (0.0591 in.) B6 36266-52390 1.94 mm (0.0764 in.) D8
36266-52180 1.52 mm (0.0598 in.) B7 36266-52400 1.96 mm (0.0772 in.) D9
36266-52190 1.54 mm (0.0606 in.) B8 36266-52410 1.98 mm (0.0780 in.) E0
36266-52200 1.56 mm (0.0614 in.) B9 36266-52420 2.00 mm (0.0787 in.) E1
36266-52210 1.58 mm (0.0622 in.) C0 36266-52430 2.02 mm (0.0795 in.) E2
36266-52220 1.60 mm (0.0630 in.) C1 - - -



Hide 16.ADJUST TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.

Rotate the transfer output shaft sub-assembly several times in the forward and backward directions.


b.

Remove the transfer ring gear and check the tooth contact.

C247128C03
0.188,1.073 0.5,1.271 0.313,0.198 10 *a 2.656,0.073 2.969,0.271 0.313,0.198 10 *b 2.688,1.823 3,2.021 0.313,0.198 10 *e 4.917,1.802 5.229,2 0.313,0.198 10 *f 4.833,0.115 5.146,0.313 0.313,0.198 10 *c 3.75,1.438 4.063,1.635 0.313,0.198 10 *d 3.75,3.24 4.063,3.438 0.313,0.198 10 *g
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from to the ring gear (*e, *f) - -


NOTICE:
·

Check the tooth contact at 4 or more locations on the transfer ring gear.

·

When replacing washers (adjusting the backlash, preload or tooth contact pattern), reapply a coat of Prussian Blue.



HINT:

The Prussian Blue pattern indicates the tooth contact points.



c.

In instances of face contact or flank contact, perform the following procedure.

i.

Move and adjust the transfer ring gear using the No. 2 transfer ring gear mounting case washer (for preload adjustment) and the No. 1 ring gear mounting case washer (for backlash adjustment).



d.

In instances of heel contact or toe contact, perform the following procedure.

i.

Select a transfer output shaft washer (for tooth contact adjustment) from the table below, and move and adjust the transfer driven pinion.

Transfer Output Shaft Washer (for tooth contact adjustment):
Part No. Thickness Identifying Mark Part No. Thickness Identifying Mark
36275-52010 1.02 mm (0.0402 in.) 01 36275-52150 1.30 mm (0.0512 in.) 15
36275-52020 1.04 mm (0.0409 in.) 02 36275-52160 1.32 mm (0.0520 in.) 16
36275-52030 1.06 mm (0.0417 in.) 03 36275-52170 1.34 mm (0.0528 in.) 17
36275-52040 1.08 mm (0.0425 in.) 04 36275-52180 1.36 mm (0.0535 in.) 18
36275-52050 1.10 mm (0.0433 in.) 05 36275-52190 1.38 mm (0.0543 in.) 19
36275-52060 1.12 mm (0.0441 in.) 06 36275-52200 1.40 mm (0.0551 in.) 20
36275-52070 1.14 mm (0.0449 in.) 07 36275-52210 1.42 mm (0.0559 in.) 21
36275-52080 1.16 mm (0.0457 in.) 08 36275-52220 1.44 mm (0.0567 in.) 22
36275-52090 1.18 mm (0.0465 in.) 09 36275-52230 1.46 mm (0.0575 in.) 23
36275-52100 1.20 mm (0.0472 in.) 10 36275-52240 1.48 mm (0.0583 in.) 24
36275-52110 1.22 mm (0.0480 in.) 11 36275-52250 1.50 mm (0.0591 in.) 25
36275-52120 1.24 mm (0.0488 in.) 12 36275-52260 1.52 mm (0.0598 in.) 26
36275-52130 1.26 mm (0.0496 in.) 13 36275-52270 1.54 mm (0.0606 in.) 27
36275-52140 1.28 mm (0.0504 in.) 14 36275-52280 1.56 mm (0.0614 in.) 28




e.

If the tooth contact has been adjusted, recheck the backlash, preload and tooth contact pattern.


Hide 36121 17.REMOVE NO. 1 TRANSFER CASE COVER

a.
C375273

Remove the 8 bolts and No. 1 transfer case cover from the transfer case.


Hide 18.REMOVE TRANSFER RING GEAR

a.
C375275

Remove the transfer ring gear from the transfer case.


Hide 36202 19.REMOVE REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

a.
C375278

Remove the 5 bolts and rear transfer output shaft sub-assembly from the transfer case.


Hide 36111G 20.INSTALL TRANSFER CASE STRAIGHT PIN

a.

Using a plastic-faced hammer, install straight pins to the locations shown in the illustration.

C375283N01
3.031,0.656 3.188,0.854 0.156,0.198 10 false A 6.51,0.729 6.667,0.927 0.156,0.198 10 false B

Drive in depth (A):

10.8 to 11.8 mm (0.426 to 0.464 in.)


Drive in depth (B):

6.5 to 7.5 mm (0.256 to 0.295 in.)



Hide 36202 21.INSTALL REAR TRANSFER OUTPUT SHAFT SUB-ASSEMBLY

a.
C130057

Secure the rear transfer output shaft sub-assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a chisel and hammer, stake the transfer gear nut.

NOTICE:

Fully stake the transfer gear nut along the entire groove.



c.
C375278

Install the rear transfer output shaft sub-assembly to the transfer case with the 5 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Do not scratch, twist or break the O-ring.



Hide 22.INSTALL TRANSFER RING GEAR

a.
C375275

Install the transfer ring gear to the transfer case.


Hide 36121 23.INSTALL NO. 1 TRANSFER CASE COVER

a.

Using a scraper, clean the seal packing from the transfer case and No. 1 transfer case cover and remove any oil using a cleaning solvent.

NOTICE:

Do not scratch the installation area.



b.
C375284C02
2.063,1.552 2.344,1.729 true 0.125,0.698 0.26,0.885 0.135,0.188 10 true A 1.302,1.208 1.573,1.417 0.271,0.208 10 false *b 2.406,1.729 2.677,1.885 0.271,0.156 10 false *a 2.76,0.49 3.01,0.688 0.25,0.198 10 false *c
*a Seal Packing
*b 30°
*c Seal Width 2.0 to 3.0 mm (0.0788 to 0.118 in.)


Apply seal packing to the transfer case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Install the cover to the case within 10 minutes of application.

·

Start the application from inside the area marked A.

·

Overlap the seal packing at least 10 mm (0.394 in.) at the beginning and the end of application.




c.
C375273

Install the No. 1 transfer case cover with the 8 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 36111B 24.INSTALL TRANSFER CASE OIL SEAL

a.
C375285C03
0.802,0.99 1.125,1.135 false 0.521,0.917 0.979,1.115 0.458,0.198 10 false SST 0.969,3.219 1.427,3.417 0.458,0.198 10 false *a
*a Drive in depth


Using SST and a hammer, tap in a new transfer case oil seal as shown in the illustration.

SST
09316-60011  (09316-00011)

Drive in depth (A):

9.5 to 10.5 mm (0.375 to 0.413 in.)


NOTICE:
·

Tap the transfer case oil seal uniformly so that the transfer case oil seal is straight.

·

Do not tap the transfer case oil seal in too far.




Hide 36113D 25.INSTALL TRANSFER CASE OIL SEAL RH

a.
C375286C03
1.823,2.219 2.146,2.375 false 2.219,2.375 2.531,2.573 0.313,0.198 10 false SST 1.885,0.458 2.198,0.656 0.313,0.198 10 false *a
*a Drive in depth


Using SST and a hammer, tap in a new transfer case oil seal RH as shown in the illustration.

SST
09316-60011  (09316-00011)

Drive in depth (A):

7.5 to 8.5 mm (0.296 to 0.334 in.)


NOTICE:
·

Tap the transfer case oil seal RH uniformly so that the transfer case oil seal RH is straight.

·

Do not tap the transfer case oil seal RH in too far.




Hide 36111H 26.INSTALL TRANSFER CASE BREATHER PLUG

a.
C375287N01
2.76,1.74 2.135,0.969 true 2.781,1.813 3.24,2.01 0.458,0.198 10 false SST

Using SST, tap in a new transfer case breather plug until it meets the transfer case.

SST
09612-10093  (09612-10061)


Hide 36114L 27.INSTALL TRANSFER FILLER PLUG

a.
C375267

Using a 10 mm socket hexagon wrench, install a new gasket and the transfer filler plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 36114F 28.INSTALL TRANSFER DRAIN PLUG

a.
C375266

Using a 10 mm socket hexagon wrench, install a new gasket and the transfer drain plug.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 36114B 29.INSTALL NO. 1 TRANSFER CASE PLUG

a.
C375265

Install a new gasket and the No. 1 transfer case plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 36100 30.REMOVE TRANSFER ASSEMBLY

a.
C375263

Remove the transfer assembly from the overhaul attachment.


Hide 36100A 31.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

a.

Clean the bolt holes.


b.
C375288C02
2.271,1.604 2.531,1.396 false 2.104,1.542 2.417,1.74 0.313,0.198 10 false *a 3.052,0.99 3.313,1.198 0.26,0.208 10 false *b
*a Adhesive 1324
*b 64 mm (2.52 in.)


Using 2 nuts, install the 4 new stud bolts in the locations shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the shorter threaded part of each stud bolt to the transfer side.