Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292816 REAR CRANKSHAFT OIL SEAL A

3ZR-FAE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly horizontally.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Keep the lip free from foreign matter.



c.
A154926C07
2.333,0.896 2.979,0.354 2.979,0.354 2.802,1.271 false 2.979,0.146 3.292,0.292 0.313,0.146 10 false SST 0.823,0.188 1.135,0.344 0.313,0.156 10 false *a
*a Tap in Depth


Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07100)

Timing Chain Oil Seal Tap in Depth:

-1.0 to 1.0 mm (-0.0394 to 0.0394 in.)


NOTICE:
·

Wipe off excess grease from the crankshaft.

·

Do not tap in the rear engine oil seal at an angle.




Hide 32101B 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A234914N20
1.365,2.25 0.74,2.74 0.74,2.74 2.365,3 true 0.438,2.667 1.031,3 0.594,0.333 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-54015  (91551-00850)
09330-00021  


b.

Clean the 8 bolts and 8 bolt holes.


c.
A252955C02
0.563,0.646 0.688,0.646 0.688,0.646 0.813,1.063 false 1.333,0.5 1.583,0.167 1.583,0.167 1.75,0.167 false 2.219,0.667 1.99,0.667 1.99,0.667 1.792,1.031 false 0.354,0.573 0.667,0.729 0.313,0.156 10 *1 1.792,0.083 2.104,0.24 0.313,0.156 10 *2 2.292,0.604 2.604,0.76 0.313,0.156 10 *3 0.083,1.333 0.396,1.49 0.313,0.156 10 *a 2.281,1.333 2.594,1.49 0.313,0.156 10 *b
*1 Front Drive Plate Spacer (Reversible)
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
*a Engine Side
*b Transaxle Side


Install the front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.


d.
A057108C38
2.521,0.26 2.031,0.26 2.031,0.26 1.75,1.292 false 2.563,0.156 2.74,0.333 0.177,0.177 10 *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A319942N02
1.656,0.583 1.813,0.781 0.156,0.198 10 true 1 1.656,1.594 1.813,1.792 0.156,0.198 10 true 2 2.135,1.104 2.292,1.302 0.156,0.198 10 true 3 1.135,1.104 1.292,1.302 0.156,0.198 10 true 4 2.031,0.792 2.188,0.99 0.156,0.198 10 true 5 1.229,1.469 1.385,1.667 0.156,0.198 10 true 6 1.365,0.688 1.521,0.885 0.156,0.198 10 true 8 2,1.458 2.156,1.656 0.156,0.198 10 true 7

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.