Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for VALEO Made)
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0293719 AIR CONDITIONING UNIT(for VALEO Made) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for VALEO Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 87102B 2.INSTALL NO. 2 RADIATOR CASE SUB-ASSEMBLY

a.
I113438

Install the No. 2 radiator case sub-assembly with the 6 screws.


Hide 88501 3.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.
I112531C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor as shown in the illustration.


b.

Connect the the connector.


Hide 87102A 4.INSTALL RADIATOR CASE SUB-ASSEMBLY

a.

Engage the claws and to install the radiator case sub-assembly.

I113436


b.

Install the 3 screws.


Hide 87611A 5.INSTALL HEAT EXCHANGER CASE

a.
I113434

Engage the 2 claws and guide, and install the heat exchanger case with the screw.


b.
I113435

Install the bracket with the 2 screws.


Hide 88515 6.INSTALL COOLER EXPANSION VALVE

a.
I113558

Install the grommet.


b.

Sufficiently apply compressor oil to 2 new O-rings and fitting surfaces of the No. 1 cooler evaporator sub-assembly.

Compressor Oil:

VC100YF or equivalent



c.

Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.
I113557

Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
4.5 N*m (46 kgf*cm, 40 in.*lbf)


Hide 87107A 7.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
I112530C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater radiator unit sub-assembly as shown in the illustration.


b.
I112377

Install the 3 screws.


Hide 87124B 8.INSTALL HEATER CLAMP

a.
I112376

Engage the claws to install the heater clamp.


b.

Install the screw.


Hide 88897M 9.INSTALL HEATER PIPE GROMMET

a.
I112375

Install the heater pipe grommet.


Hide 87050D 10.INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.
I112857C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 2 air conditioning radiator damper servo sub-assembly as shown in the illustration.


b.
I113789C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 2 air conditioning radiator damper servo sub-assembly to engage the claw as shown in the illustration.


Hide 87050C 11.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Automatic Air Conditioning System)

a.

for Lower RH Side:

i.
I112840C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.


ii.
I112528C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 1 air conditioning radiator damper servo sub-assembly to engage the claw as shown in the illustration.


iii.

Engage the snap.



b.

for Upper RH Side:

i.
I112838C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.


ii.
I113791C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 1 air conditioning radiator damper servo sub-assembly to engage the claw as shown in the illustration.



c.

for Lower LH Side:

i.
I112836C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.


ii.
I112524C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 1 air conditioning radiator damper servo sub-assembly to engage the claw as shown in the illustration.


iii.

Engage the snap.



d.

for Upper LH Side:

i.
I112834C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.


ii.
I113787C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 1 air conditioning radiator damper servo sub-assembly to engage the claw as shown in the illustration.



Hide 87050C 12.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Manual Air Conditioning System)

a.

for Lower RH Side:

i.
I112840C02
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.


ii.
I112374C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 1 air conditioning radiator damper servo sub-assembly to engage the claw as shown in the illustration.


iii.

Engage the snap.



b.

for Upper RH Side:

i.
I112838C02
0,0 0,0 false
V113147

Install in this Direction


Install the No. 1 air conditioning radiator damper servo sub-assembly as shown in the illustration.


ii.
I113790C01
0,0 0,0 false
V113147

Install in this Direction


Turn the No. 1 air conditioning radiator damper servo sub-assembly to engage the claw as shown in the illustration.



Hide 88539C 13.INSTALL NO. 2 COOLER UNIT DRAIN HOSE

a.
I113432

Install the No. 2 cooler unit drain hose.


Hide 88539J 14.INSTALL DRAIN COOLER HOSE

a.
I112369

Install the drain cooler hose.


Hide 82210K 15.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.

for Automatic Air Conditioning System:

i.

Engage clamps to install the air conditioning harness assembly.

I112368


ii.

Connect the 5 connectors.



b.

for Manual Air Conditioning System:

i.

Engage clamps to install the air conditioning harness assembly.

I112858


ii.

Connect the 3 connectors.



Hide 88650N 16.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

a.

for LHD:

i.
I112521C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides to temporarily install the air conditioning amplifier assembly as shown in the illustration.


ii.
I112364

Install the air conditioning amplifier assembly with the screw.


iii.

Connect the connector.



b.

for RHD:

i.
I112522C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides to temporarily install the air conditioning amplifier assembly as shown in the illustration.


ii.
I112366

Install the air conditioning amplifier assembly with the screw.


iii.

Connect the connector.



Hide 87114B 17.INSTALL HEATER COVER (w/o PTC Heater)

a.
I112568C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater cover with the 2 screws as shown in the illustration.


Hide 87710G 18.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)

a.
I112569C01
0,0 0,0 false
V113147

Install in this Direction


Install the quick heater assembly with the 2 screws as shown in the illustration.


Hide 87114L 19.INSTALL NO. 2 HEATER COVER (w/ PTC Heater)

a.

Remove the No. 2 heater cover with the screw.


Hide 88539E 21.INSTALL NO. 3 COOLER UNIT DRAIN HOSE

a.
I113431

Install the No. 3 cooler unit drain hose.


Hide 82143 22.INSTALL NO. 3 INSTRUMENT PANEL WIRE (w/ PTC Heater)

a.
I112361

Engage the clamps to install the No. 3 instrument panel wire.


b.

Connect the connector.


Hide 88482A 23.INSTALL COVER (w/o Rear Air Duct)

a.
I112502

Engage the claws to install the cover.


Hide 88505 24.INSTALL AIR CONDITIONING DUCT SUB-ASSEMBLY

a.
I112360

Engage the guide to install the air conditioning duct sub-assembly.


Hide 87211A 25.INSTALL NO. 2 AIR DUCT (for LHD)

a.
I112570C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the No. 2 air duct as shown in the illustration.


b.

Install the screw.


Hide 87211 26.INSTALL NO. 1 AIR DUCT (for RHD)

a.
I112571C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the No. 1 air duct as shown in the illustration.


b.

Install the screw.