Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059856 INTERIOR PANELS / TRIM _0293792 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 63344 1.REMOVE NO. 4 ROOF SILENCER PAD (w/ Safety Connect System)

a.

Remove the No. 4 roof silencer pad.

B461371


Hide 63343 2.REMOVE NO. 3 ROOF SILENCER PAD (w/ Safety Connect System)

a.

Remove the No. 3 roof silencer pad.

B461373


Hide 63341 3.REMOVE NO. 1 ROOF SILENCER PAD (w/ Safety Connect System)

a.

Peel off the double-sided tape to remove the 2 No. 1 roof silencer pads.

HINT:

Remove any double-sided tape remaining on the roof headlining.


B461369


Hide 63341 4.REMOVE NO. 1 ROOF SILENCER PAD (w/o Safety Connect System)

a.

Remove the No. 1 roof silencer pad.

B461375


Hide 63387 5.REMOVE ROOF HEADLINING FORMING PAD (w/ Map Light)

a.

Remove the 2 roof headlining forming pads.

B461444


Hide 63342 6.REMOVE NO. 2 ROOF SILENCER PAD (w/ Map Light)

a.

Remove the 2 No. 2 roof silencer pads.

B461377


Hide 63341G 7.REMOVE ROOF SILENCER PAD (w/ Map Light)

a.

Remove the 2 roof silencer pads.

B461379


Hide 82171 8.REMOVE NO. 1 ROOF WIRE

a.

for TMMT Made:

B461381C01
0.156,0.146 0.531,0.385 0.375,0.24 12 false *A 0.167,1.417 0.542,1.656 0.375,0.24 12 false *B 0.167,1.625 0.542,1.865 0.375,0.24 12 false *C 3.333,0.354 3.646,0.594 0.313,0.24 12 true *D 4.708,2.146 5.021,2.385 0.313,0.24 12 true *E
*A w/ Vanity Light *B w/ Rain Sensor
*C w/ Lane Departure Alert System *D w/ Intrusion Sensor
*E w/ Map Light - -


i.

Disengage each guide.


ii.

Peel off the pieces of each adhesive tape and remove the No. 1 roof wire.



b.

except TMMT Made:

B461405C01
0.74,0.5 0.927,0.323 false 3.938,1.302 4.021,1.5 true 4.406,1.417 4.49,1.615 true 0.75,0.833 0.438,1.063 true 2.896,2.396 3.292,2.24 true 0.177,0.156 0.427,0.396 0.25,0.24 12 true *A 0.167,1.417 0.417,1.635 0.25,0.219 12 true *B 3.74,0.156 3.99,0.375 0.25,0.219 12 true *B 0.958,0.229 1.271,0.427 0.313,0.198 10 false *a 3.76,1.167 4.073,1.365 0.313,0.198 10 false *a 4.458,1.646 4.771,1.844 0.313,0.198 10 false *b 0.271,1.052 0.583,1.25 0.313,0.198 10 false *b 3.333,2.125 3.563,2.333 0.229,0.208 10 true *a
*A w/ Rain Sensor *B w/ Vanity Light
*a Clamp *b Guide


i.

Disengage each guide.


ii.

Using a clip remover, disengage each clamp.


iii.

Peel off the pieces of each adhesive tape and remove the No. 1 roof wire.



c.
B461402C01
0,0 0,0 false
V113147

Remove in this Direction


w/ Vanity Light:

i.

Turn the visor connector approximately 90° counterclockwise and disconnect the visor connectors as shown in the illustration.

HINT:

Use the same procedures for the opposite side.




Hide 86101J 9.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 63323E 10.REMOVE HEADLINING LIGHT CASE (w/ Map Light)

a.

Remove the headlining light case.

B461394


Hide 63398 11.REMOVE ROOF HEADLINING SUPPORT PLATE (w/ Intrusion Sensor)

a.

Remove the roof headlining support plate.

B461395