Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059856 INTERIOR PANELS / TRIM _0293792 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 63398 1.INSTALL ROOF HEADLINING SUPPORT PLATE (w/ Intrusion Sensor)

a.

Align the markings on the roof headlining with the roof headlining support plate and install it using hot melt glue.

B461407C01
2.25,1.917 2.51,1.917 true 2.573,1.865 2.802,2.073 0.229,0.208 10 true *a
*a Marking - -



Hide 63323E 2.INSTALL HEADLINING LIGHT CASE (w/ Map Light)

a.

Align the markings on the roof headlining with the headlining light case and install it using hot melt glue.

B461406C01
2.052,1.927 2.354,1.927 true 2.406,1.865 2.656,2.073 0.25,0.208 10 true *a
*a Marking - -



Hide 86101J 3.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

Hide 82171 4.INSTALL NO. 1 ROOF WIRE

a.
B461403C01
0,0 0,0 false
V113147

Install in this Direction


w/ Vanity Light:

i.

Turn the visor connectors approximately 90° clockwise to connect the visor connector as shown in the illustration.

HINT:

Use the same procedures for the opposite side.




b.

for TMMT Made:

B461404C01
0.688,1.781 0.938,1.698 true 1.385,2.979 1.573,2.823 true 2.75,2.552 2.938,2.396 true 0.313,0.219 0.688,0.458 0.375,0.24 12 false *A 0.313,0.448 0.688,0.688 0.375,0.24 12 false *B 0.313,2.323 0.688,2.563 0.375,0.24 12 false *C 0.521,1.729 0.833,1.927 0.313,0.198 10 false *a 1.594,2.698 1.792,2.948 0.198,0.25 10 true *a 2.969,2.281 3.167,2.531 0.198,0.25 10 true *a
*A w/ Rain Sensor *B w/ Lane Departure Alert System
*C w/ Vanity Light - -
*a Marking - -
V100155

Double-sided Tape - -


i.

Apply double-sided tape as shown in the illustration.

NOTICE:

Apply the supports with uniform loading, and without protruding from the roof headlining markings.



ii.

Line up the No. 1 roof wire positioning tape and the roof headlining markings.


iii.

Align new pieces of each adhesive tapes with the markings of the roof headlining and install them.

B461381C01
0.156,0.146 0.531,0.385 0.375,0.24 12 false *A 0.167,1.417 0.542,1.656 0.375,0.24 12 false *B 0.167,1.625 0.542,1.865 0.375,0.24 12 false *C 3.333,0.354 3.646,0.594 0.313,0.24 12 true *D 4.708,2.146 5.021,2.385 0.313,0.24 12 true *E
*A w/ Vanity Light *B Rain Sensor
*C w/ Lane Departure Alert System *D w/ Intrusion Sensor
*E w/ Map Light - -



iv.

Engage each guide.



c.

except TMMT Made:

i.

Line up the No. 1 roof wire positioning tape and the roof headlining markings.


ii.

Align new pieces of each adhesive tapes with the markings of the roof headlining and install them.

B461405C01
0.74,0.5 0.927,0.323 false 3.938,1.302 4.021,1.5 true 4.406,1.417 4.49,1.615 true 0.75,0.833 0.438,1.063 true 2.896,2.396 3.292,2.24 true 0.177,0.156 0.427,0.396 0.25,0.24 12 true *A 0.167,1.417 0.417,1.635 0.25,0.219 12 true *B 3.74,0.156 3.99,0.375 0.25,0.219 12 true *B 0.958,0.229 1.271,0.427 0.313,0.198 10 false *a 3.76,1.167 4.073,1.365 0.313,0.198 10 false *a 4.458,1.646 4.771,1.844 0.313,0.198 10 false *b 0.271,1.052 0.583,1.25 0.313,0.198 10 false *b 3.333,2.125 3.563,2.333 0.229,0.208 10 true *a
*A w/ Rain Sensor *B w/ Vanity Light
*a Clamp *b Guide



iii.

Engage each guide.


iv.

Engage each clamp.



Hide 63341G 5.INSTALL ROOF SILENCER PAD (w/ Map Light)

a.

Align the markings on the roof headlining with the 2 roof silencer pads and install them using hot melt glue.

B461380C01
4.833,1.906 5.094,1.906 true 3.854,1.906 4.115,1.906 true 5.135,1.844 5.354,2.063 0.219,0.219 10 true *a 3.604,1.833 3.823,2.052 0.219,0.219 10 true *a
*a Marking - -



Hide 63342 6.INSTALL NO. 2 ROOF SILENCER PAD (w/ Map Light)

a.

Align the markings on the roof headlining with the 2 No. 2 roof silencer pads and install them using hot melt glue.

B461378C01
3.094,1.896 2.865,1.896 true 5.563,1.906 5.333,1.906 true 2.604,1.823 2.844,2.031 0.24,0.208 10 true *a 5.604,1.833 5.844,2.042 0.24,0.208 10 true *a
*a Marking - -



Hide 63387 7.INSTALL ROOF HEADLINING FORMING PAD (w/ Map Light)

a.

Align the markings on the roof headlining with the 2 roof headlining forming pads and install them using hot melt glue.

B461445C01
2.49,1.281 2.792,1.573 true 2.49,2.531 2.76,2.292 true 2.823,1.594 3.042,1.813 0.219,0.219 10 true *a 2.792,2.198 3.01,2.417 0.219,0.219 10 true *a
*a Marking - -



Hide 63341 8.INSTALL NO. 1 ROOF SILENCER PAD (w/o Safety Connect System)

a.

Align the markings on the roof headlining with the No. 1 roof silencer pad and install it using hot melt glue.

B461376C01
2.948,1.927 3.156,1.927 true 3.198,1.875 3.427,2.083 0.229,0.208 10 true *a
*a Marking - -



Hide 63341 9.INSTALL NO. 1 ROOF SILENCER PAD (w/ Safety Connect System)

a.

Align a new No. 1 roof silencer pad with the silencer markings on the roof headlining and install the No. 1 roof silencer pad using double-sided tape.

HINT:

Peel off the backing paper from the double-sided tape before installing the No. 1 roof silencer pad.


B461370C01
1.604,1.01 1.958,1.01 true 1.594,2.823 1.948,2.823 true 1.396,2.74 1.708,2.938 0.313,0.198 10 false *a 1.385,0.927 1.698,1.125 0.313,0.198 10 false *a
*a Marking - -



Hide 63343 10.INSTALL NO. 3 ROOF SILENCER PAD (w/ Safety Connect System)

a.

Align the markings on the roof headlining with the No. 3 roof silencer pad and install it using hot melt glue.

B461374C01
3.021,2 3.281,2 true 3.323,1.927 3.573,2.146 0.25,0.219 10 true *a
*a Marking - -



Hide 63344 11.INSTALL NO. 4 ROOF SILENCER PAD (w/ Safety Connect System)

a.

Align the markings on the roof headlining with the No. 4 roof silencer pad and install it using hot melt glue.

B461372C01
3.021,1.823 3.229,1.823 true 3.26,1.76 3.5,1.99 0.24,0.229 10 true *a
*a Marking - -