Home › Engine / Hybrid System › 8NR-FTS (INTAKE / EXHAUST) › TURBOCHARGER
RM32H0E _51 Engine / Hybrid System _059908 8NR-FTS INTAKE / EXHAUST _0293887 TURBOCHARGER A

8NR-FTS INTAKE / EXHAUST  TURBOCHARGER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during turbocharger sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 25051 2.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

Hide 15407 3.DISCONNECT INLET TURBO OIL PIPE SUB-ASSEMBLY

a.
A353527

Remove the 4 bolts and union bolt and disconnect the inlet turbo oil pipe sub-assembly.


b.
A351382

Remove the inlet turbo oil gasket from the inlet turbo oil pipe sub-assembly.


c.
A355596

Remove the outlet No. 1 turbo oil gasket from the stiffening crankcase assembly.


d.

Remove the gasket from the inlet turbo oil pipe sub-assembly.


Hide 16027 4.DISCONNECT NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A351383

Remove the bolt, 2 nuts and No. 1 turbo water pipe sub-assembly from the turbocharger sub-assembly.


b.

Remove the water by-pass gasket from the No. 1 turbo water pipe sub-assembly.


Hide 17201 5.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A353526

Disconnect the intake air control valve (air by-pass valve assembly) connector.


b.
A351384

Remove the 3 bolts and turbocharger sub-assembly from the cylinder head sub-assembly.


c.
A351385

Remove the outlet compressor gasket from the turbocharger sub-assembly.


Hide 6.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A392851C01
0.135,0.156 0.417,0.375 0.281,0.219 12 false *A 0.115,2.438 0.427,2.688 0.313,0.25 12 false *B 0.094,2.76 0.406,2.917 0.313,0.156 10 false *1 1.781,3.927 2.094,4.083 0.313,0.156 10 false *2 0.385,2.51 0.698,2.667 0.313,0.156 10 false *1 0.302,4.198 0.615,4.354 0.313,0.156 10 false *1 0.969,3.677 1.188,3.844 0.219,0.167 10 true *1 2.302,2.844 2.5,3 0.198,0.156 10 true *2 0.396,0.323 0.708,0.479 0.313,0.156 10 false *1 0.094,0.583 0.406,0.74 0.313,0.156 10 false *1 0.323,2.01 0.635,2.167 0.313,0.156 10 false *1 0.99,1.521 1.198,1.688 0.208,0.167 10 true *1 1.802,1.719 2.115,1.875 0.313,0.156 10 false *2 2.281,0.635 2.49,0.813 0.208,0.177 10 true *2
*A for 2WD
*B for AWD
*1 Stud Bolt (A)
*2 Stud Bolt (B)


Using an E10 "TORX" socket wrench, remove the 4 stud bolts (A) from the turbocharger sub-assembly.


b.

Using an E6 "TORX" socket wrench, remove the 2 stud bolts (B) from the turbocharger sub-assembly.