Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL PRESSURE SENSOR
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293897 FUEL PRESSURE SENSOR A

8NR-FTS FUEL  FUEL PRESSURE SENSOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL PIPE PLUG SUB-ASSEMBLY

a.

Install a new O-ring, new No. 1 fuel injector back-up ring, new No. 2 fuel injector back-up ring and new No. 3 fuel injector back-up ring to the fuel pipe plug sub-assembly as shown in the illustration.

A381153C02
4.031,0.375 4.323,0.375 false 4.958,0.625 5.052,0.625 5.052,0.625 5.177,1.01 false 5.375,1.073 5.51,0.677 5.51,0.677 5.604,0.677 false 5.479,1.583 5.625,1.896 5.625,1.896 5.719,1.896 false 5.417,2.854 5.531,2.854 5.531,2.854 5.646,3.125 false 5.854,2.802 5.979,2.802 5.979,2.802 6.083,3.031 false 6.552,3.281 6.552,2.958 6.552,2.958 6.656,2.958 false 6.396,3.531 6.396,3.354 false 4.948,1.865 4.948,1.688 false 3.854,0.313 4.167,0.469 0.313,0.156 10 false *1 4.854,1.896 5.167,2.052 0.313,0.156 10 false *2 5.667,0.615 5.979,0.771 0.313,0.156 10 false *3 5.771,1.833 6.083,1.99 0.313,0.156 10 false *4 4.781,0.563 5.094,0.719 0.313,0.156 10 false *5 1.854,1.167 2.167,1.323 0.313,0.156 10 false *a 1.052,2.354 1.365,2.51 0.313,0.156 10 false *b 2.833,2.375 3.146,2.531 0.313,0.156 10 false *c 1.917,1.708 2.229,1.865 0.313,0.156 10 false *d 1.052,1.688 1.365,1.844 0.313,0.156 10 false *e 5.229,2.792 5.542,2.948 0.313,0.156 10 false *2 5.677,2.74 5.99,2.896 0.313,0.156 10 false *5 6.698,2.896 7.01,3.052 0.313,0.156 10 false *4 6.323,3.552 6.635,3.708 0.313,0.156 10 false *3 2.813,1.708 3.125,1.865 0.313,0.156 10 false *e
*1 Fuel Pipe Plug Sub-assembly *2 No. 1 Fuel Injector Back-up Ring
*3 No. 2 Fuel Injector Back-up Ring *4 No. 3 Fuel Injector Back-up Ring
*5 O-ring - -
*a Opening *b Overlapped
*c Stretched *d Correct
*e Incorrect - -


NOTICE:
·

Check that there is no foreign matter or damage on the O-ring groove of the fuel pipe plug sub-assembly.

·

Check that the No. 1 fuel injector back-up ring and No. 3 fuel injector back-up ring are installed in the correct orientation.

·

Make sure that the No. 1 fuel injector back-up ring, No. 2 fuel injector back-up ring, No. 3 fuel injector back-up ring and O-ring are installed in the correct order.

·

Check that the opening of the No. 1 fuel injector back-up ring is not overlapped or stretched as shown in the illustration.

·

After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.




b.

Install the dust cap sub-assembly to the fuel pipe plug sub-assembly.


c.
A381154

Install a new gasket to the fuel pipe plug sub-assembly as shown in the illustration.


d.

Secure the fuel delivery pipe in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Using a 5 mm hexagon socket wrench, install the fuel pipe plug sub-assembly to the fuel delivery pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Remove the fuel delivery pipe from the vise.


Hide 23814B 2.INSTALL FUEL DELIVERY PIPE (FUEL PRESSURE SENSOR)

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL INJECTOR>INSTALLATION

NOTICE:
·

Do not remove the fuel pressure sensor from the fuel delivery pipe.

·

If the fuel pressure sensor is removed, replace the fuel delivery pipe (fuel pressure sensor) with a new one.