Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM32H0E _55 Steering _059604 STEERING COLUMN _0293907 STEERING LOCK SYSTEM U

STEERING COLUMN  STEERING LOCK SYSTEM  TERMINALS OF ECU  


TERMINAL INSPECTION


B118684C33
1.667,0.917 2.167,1.167 0.5,0.25 0.281,0.125 0.51,0.292 0.229,0.167 10 false *a 1.802,0.917 2.323,1.177 0.521,0.26 10 false F78
*a Component without harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
- -


a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F78-1 (GND) - Body ground - W-B - Body ground Ground*1 Always Below 1 Ω -
F78-3 (IGE) - F78-1 (GND) Input P - W-B Steering lock motor activation command signal (motor activation command signal sent from certification ECU (smart key ECU assembly)) Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P

·

Steering lock unlocked in advance by carrying key and turning engine switch on (IG)

·

After above conditions met, engine switch turned off


Pulse generation (see waveform)
Entry&Start
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


F78-4 (SLP1) - F78-1 (GND) Output G - W-B Steering lock bar position signal (output signal from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V
Entry&Start
·

Sensor Value


F78-5 (LIN) - F78-1 (GND) Input/Output V - W-B LIN communication line - -
Entry&Start
·

Steering Lock Start Cond


F78-6 (IG2) - F78-1 (GND) Input B - W-B Power source mode signal (IG2 power supply input for entire steering lock actuator or upper bracket assembly)*1 Engine switch off → engine switch on (IG) Below 1 V → 11 to 14 V -
F78-7 (B) - Body ground Input L - Body ground Power source*1 Always 11 to 14 V -

*1: When there is a problem with the power source input, the certification ECU (smart key ECU assembly) may store DTC B2786.


NOTICE:

There is 1 motor and 2 sensors built into the steering lock actuator or upper bracket assembly.


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.




i.
C221561C19
0.292,0.396 1.698,0.563 1.406,0.167 1.521,1.583 2.49,1.708 0.969,0.125 2.292,0.448 2.719,0.604 0.427,0.156 2.083,1.708 2.167,1.99 2.167,1.99 2.219,1.99 false 1.698,0.438 2.813,0.198 2.813,0.198 2.885,0.198 false 2.802,0.198 2.604,0.448 false 2.917,1.583 3.385,1.958 0.469,0.375 10 GND 2.271,1.906 2.76,2.052 0.49,0.146 10 *b 2.948,0.104 3.313,0.333 0.365,0.229 10 *a
*a Steering Lock Motor not Operating
*b Steering Lock Motor Operating


Waveform

Item Content
Tester Connection F78-3 (IGE) - F78-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Operating → Not operating