Home › Audio / Visual / Telematics › TELEMATICS › TELEPHONE ANTENNA CORD › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060052 TELEMATICS _0294135 TELEPHONE ANTENNA CORD A

TELEMATICS  TELEPHONE ANTENNA CORD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the telephone antenna cord removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

PROCEDURE

Hide 55401E 1.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 55086 2.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 63311C 3.REMOVE ROOF HEADLINING

Hide 86101 4.REMOVE ANTENNA CORD SUB-ASSEMBLY

a.
E357305

Disengage the guides to remove the antenna cord sub-assembly.


Hide 86101J 5.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

Type A:

i.

Remove the adhesive tape from the roof headlining.

E361587C01
0,0 0,0 false
V100155

Adhesive Tape
V100136

Front



ii.

Disengage the clamp and notch to remove the No. 2 antenna cord sub-assembly from the roof headlining.



b.

Type B:

i.

Remove the adhesive tape from the roof headlining.

E353818C03
2.729,0.958 2.823,0.771 false 6.042,1.198 6.323,1.031 true 6.625,1.146 6.833,1.573 true 6.635,0.719 6.479,0.948 true 4.896,1.396 4.604,1.354 false 5.521,2.135 5.188,1.813 true 6.406,2.604 5.896,2.417 true 4.385,2.688 3.865,2.313 true 4.385,2.677 4.25,2.323 true 4.406,2.667 4.615,2.323 true 4.385,2.667 5.094,2.365 true 4.417,2.688 5.583,2.313 true 1.854,1.156 2.344,1.042 true 3.323,1.552 2.323,2.021 true 3.302,1.573 2.708,2.063 true 3.323,1.573 2.917,2.094 true 3.302,1.583 3.125,2.125 true 3.333,1.573 3.51,2.104 true 2.833,0.635 3.146,0.833 0.313,0.198 10 false *a 5.885,1.188 6.198,1.385 0.313,0.198 10 false *b 6.792,1.615 7.104,1.813 0.313,0.198 10 false *c 6.656,0.604 6.969,0.802 0.313,0.198 10 false *g 4.417,1.281 4.729,1.479 0.313,0.198 10 false *d 4.979,1.698 5.292,1.896 0.313,0.198 10 false *e 6.49,2.594 6.802,2.792 0.313,0.198 10 false *l 4.302,2.719 4.615,2.917 0.313,0.198 10 true *d 1.667,1.125 1.979,1.323 0.313,0.198 10 false *f 3.323,1.385 3.635,1.583 0.313,0.198 10 false *d
V100155

Adhesive Tape
V100136

Front



ii.

Disengage the clamp and notch to remove the No. 2 antenna cord sub-assembly from the roof headlining.



Hide 86101D 6.REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.
E357035C01
1.76,0.833 1.531,0.615 true 1,1.49 0.792,1.281 true 0.563,2.167 0.354,1.958 true 0.427,2.896 0.271,2.729 true 2.573,2.021 2.385,2.177 true 1.333,0.542 1.531,0.729 0.198,0.188 10 true *a 2.583,1.917 2.781,2.083 0.198,0.167 10 true *b 0.615,1.167 0.813,1.354 0.198,0.188 10 true *a 0.156,1.844 0.354,2.031 0.198,0.188 10 true *a 0.083,2.625 0.281,2.813 0.198,0.188 10 true *a
*a Clamp
*b Guide


Disconnect the connector.


b.

Remove the bolt.


c.

Using a clip remover, disengage the clamps and guide to remove the No. 3 antenna cord sub-assembly.