Home › Audio / Visual / Telematics › TELEMATICS › TELEPHONE ANTENNA CORD › 2016.10–2018.05
RM32H0E _56 Audio / Visual / Telematics _060052 TELEMATICS _0294135 TELEPHONE ANTENNA CORD A

TELEMATICS  TELEPHONE ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101D 1.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.
E357035C01
1.76,0.833 1.531,0.615 true 1,1.49 0.792,1.281 true 0.563,2.167 0.354,1.958 true 0.427,2.896 0.271,2.729 true 2.573,2.021 2.385,2.177 true 1.333,0.542 1.531,0.729 0.198,0.188 10 true *a 2.583,1.917 2.781,2.083 0.198,0.167 10 true *b 0.615,1.167 0.813,1.354 0.198,0.188 10 true *a 0.156,1.844 0.354,2.031 0.198,0.188 10 true *a 0.083,2.625 0.281,2.813 0.198,0.188 10 true *a
*a Clamp
*b Guide


Engage the clamps and guide to install the No. 3 antenna cord sub-assembly.


b.

Install the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


c.

Connect the connector.


Hide 86101J 2.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

Type A:

i.

Remove the old double-sided tape from the roof headlining.

E353816C01
4.24,1.104 4.448,1.448 true 4.51,1.438 4.74,1.625 0.229,0.188 10 true *a
*A w/ Digital Audio Broadcasting Antenna - -
*a Marking - -
V100144

Double-sided Tape
V100136

Front



ii.

Prepare an appropriate amount of new double-sided tape.

HINT:

Be careful not to touch the adhesive surface.



iii.

Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining.


iv.

Peel off the release paper from the double-sided tape.


v.

Engage the No. 2 antenna cord sub-assembly to the notch of the roof headlining.

E361589C01
2.042,1.198 2.479,1.031 true 2.875,0.958 3.406,0.771 true 4.625,1.438 4.896,1.375 true 6.5,0.969 6.646,0.76 true 6.01,1.271 6.354,1.031 true 6.854,1.583 6.615,1.115 true 5.302,2.479 5.427,2.188 true 2.51,2.104 2.74,1.792 true 5.74,2.74 5.865,2.448 true 3.458,0.677 3.771,0.875 0.313,0.198 10 false *a 1.865,1.156 2.177,1.354 0.313,0.198 10 false *e 4.427,1.385 4.74,1.583 0.313,0.198 10 false *d 6.677,0.635 6.99,0.833 0.313,0.198 10 false *f 5.833,1.26 6.083,1.531 0.25,0.271 10 false *b 5.198,2.51 5.51,2.708 0.313,0.198 10 true *g 2.781,1.635 3.094,1.833 0.313,0.198 10 false *d 6.844,1.625 7.094,1.896 0.25,0.271 10 false *c 5.625,2.76 5.938,2.958 0.313,0.198 10 true *h
*a Marking Tape (A) *b Marking Tape (B)
*c Adhesive Tape (A) *d Adhesive Tape (B)
*e Protrusion *f Edge of the roof headlining
*g Marking (A) *h Adjustment Area
V100136

Front - -



vi.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.


vii.

Install the No. 2 antenna cord sub-assembly on the double-sided tape of the roof headlining from the marking tape (A) to the marking (A).

NOTICE:
·

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




viii.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the edge of roof headlining on the roof headlining and secure the No. 2 antenna cord sub-assembly with the adhesive tape (A) as shown in the illustration.

NOTICE:

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.



ix.

Apply the adhesive tape (B) as shown in the illustration to secure the No. 2 antenna cord subassembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




b.

Type B:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.

E353818C03
2.729,0.958 2.823,0.771 false 6.042,1.198 6.323,1.031 true 6.625,1.146 6.833,1.573 true 6.635,0.719 6.479,0.948 true 4.896,1.396 4.604,1.354 false 5.521,2.135 5.188,1.813 true 6.406,2.604 5.896,2.417 true 4.385,2.688 3.865,2.313 true 4.385,2.677 4.25,2.323 true 4.406,2.667 4.615,2.323 true 4.385,2.667 5.094,2.365 true 4.417,2.688 5.583,2.313 true 1.854,1.156 2.344,1.042 true 3.323,1.552 2.323,2.021 true 3.302,1.573 2.708,2.063 true 3.323,1.573 2.917,2.094 true 3.302,1.583 3.125,2.125 true 3.333,1.573 3.51,2.104 true 2.833,0.635 3.146,0.833 0.313,0.198 10 false *a 5.885,1.188 6.198,1.385 0.313,0.198 10 false *b 6.792,1.615 7.104,1.813 0.313,0.198 10 false *c 6.656,0.604 6.969,0.802 0.313,0.198 10 false *g 4.417,1.281 4.729,1.479 0.313,0.198 10 false *d 4.979,1.698 5.292,1.896 0.313,0.198 10 false *e 6.49,2.594 6.802,2.792 0.313,0.198 10 false *l 4.302,2.719 4.615,2.917 0.313,0.198 10 true *d 1.667,1.125 1.979,1.323 0.313,0.198 10 false *f 3.323,1.385 3.635,1.583 0.313,0.198 10 false *d
*a Marking Tape (A) *b Marking Tape (B)
*c Adhesive Tape (A) *d Adhesive Tape (B)
*e Marking (A) *f Protrusion
*g Edge of the roof headlining - -
V100136

Front - -



ii.

Install the No. 2 antenna cord sub-assembly on the butyl tape of the roof headlining from the marking tape (A) to the marking (A).

NOTICE:
·

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




iii.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the edge of roof headlining on the roof headlining and secure the No. 2 antenna cord sub-assembly with the adhesive tape (A) as shown in the illustration.

NOTICE:

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.



iv.

Apply the adhesive tape (B) as shown in the illustration to secure the No. 2 antenna cord subassembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




Hide 86101 3.INSTALL ANTENNA CORD SUB-ASSEMBLY

a.
E357305

Engage the guides to install the antenna cord sub-assembly.


Hide 55086 5.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY

Hide 55401E 6.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY