Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1612/83  Lost Communication with Front Airbag Sensor RH  B1613/83  Front Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1612/83 Lost Communication with Front Airbag Sensor RH Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the front airbag sensor RH circuit.

·

The airbag sensor assembly detects a short to ground in the front airbag sensor RH circuit.

·

The airbag sensor assembly detects a short to B+ in the front airbag sensor RH circuit.

·

The airbag sensor assembly detects an open in the front airbag sensor RH circuit.

·

Front airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1613/83 Front Airbag Sensor RH Initialization Incomplete Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the front airbag sensor RH circuit.

·

The airbag sensor assembly detects a short to ground in the front airbag sensor RH circuit.

·

The airbag sensor assembly detects a short to B+ in the front airbag sensor RH circuit.

·

The airbag sensor assembly detects an open in the front airbag sensor RH circuit.

·

Front airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions (B1612/83):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the front airbag sensor RH circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the front airbag sensor RH circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the front airbag sensor RH circuit - - ○ - - -
The airbag sensor assembly detects an open in the front airbag sensor RH circuit - - - ○ - -
Front airbag sensor RH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

DTC Detection Conditions (B1613/83):
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the front airbag sensor RH circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the front airbag sensor RH circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the front airbag sensor RH circuit - - ○ - - -
The airbag sensor assembly detects an open in the front airbag sensor RH circuit - - - ○ - -
Front airbag sensor RH malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C370501E02
1.469,0.896 1.927,1.094 0.458,0.198 10 false +SR 1.51,2.052 1.969,2.25 0.458,0.198 10 false -SR 1.854,0.802 2.313,1 0.458,0.198 10 false 2 1.865,1.958 2.323,2.156 0.458,0.198 10 false 1 3.469,0.896 3.927,1.094 0.458,0.198 10 false AF5 3.448,2.073 3.906,2.271 0.458,0.198 10 false AF5 3.521,0.719 3.979,0.917 0.458,0.198 10 false 4 3.51,1.865 3.969,2.063 0.458,0.198 10 false 3 5.115,0.76 5.573,0.958 0.458,0.198 10 false 29 5.115,1.948 5.573,2.146 0.458,0.198 10 false 27 5.323,2.917 5.781,3.115 0.458,0.198 10 false A70 0.51,2.917 0.969,3.115 0.458,0.198 10 false A30 5.417,0.885 5.875,1.083 0.458,0.198 10 false +SR 5.417,2.063 5.875,2.26 0.458,0.198 10 false -SR 0.51,3.073 2.552,3.302 2.042,0.229 10 false Front Airbag Sensor RH 5.323,3.083 6.969,3.323 1.646,0.24 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)
a.

Connect the connectors that link the engine room main wire and instrument panel wire.

C284127C04
1.198,0.542 1.5,0.74 0.302,0.198 0.729,2.938 1.052,3.146 0.323,0.208 4.823,0.552 5.135,0.76 0.313,0.208 4.344,2.938 4.677,3.146 0.333,0.208 1.896,1.063 2.156,0.74 true 2.594,1.083 2.302,0.74 true 2.24,1.219 2.24,0.969 false 5.865,1.229 5.865,0.979 false 5.531,1.073 5.792,0.75 true 6.26,1.083 5.938,0.75 true 1.135,3.406 1.354,3.042 true 1.802,3.406 1.542,3.042 true 4.75,3.406 4.969,3.042 true 5.427,3.417 5.177,3.042 true 0.094,0.104 0.49,0.438 0.396,0.333 10 false *A 3.823,0.094 4.219,0.417 0.396,0.323 10 false *B 0.625,1.708 0.917,1.917 0.292,0.208 10 false *1 2.615,1.969 3.01,2.375 0.396,0.406 10 false *2 2.177,1.219 2.49,1.552 0.313,0.333 10 false *3 1.146,0.229 1.5,0.5 0.354,0.271 10 false *a 0.646,2.625 0.979,3.115 0.333,0.49 10 false *b 2.271,1.719 2.563,1.927 0.292,0.208 10 false A 2.021,1.719 2.313,1.927 0.292,0.208 10 false B 1.646,1.719 1.938,1.927 0.292,0.208 10 false C 1.521,1.719 1.813,1.927 0.292,0.208 10 false D 1.156,1.719 1.448,1.927 0.292,0.208 10 false E 0.906,1.708 1.198,1.917 0.292,0.208 10 false F 1.74,1.083 2.24,1.396 0.5,0.313 10 false -SR 2.458,1.083 2.875,1.333 0.417,0.25 10 false +SR 1.24,0.563 1.552,0.896 0.313,0.333 10 false F70 0.781,2.958 1.198,3.292 0.417,0.333 10 false A30 4.875,0.573 5.188,0.906 0.313,0.333 10 false F70 4.771,0.25 5.083,0.583 0.313,0.333 10 false *a 5.385,1.083 5.719,1.333 0.333,0.25 10 false -SR 6.125,1.083 6.49,1.354 0.365,0.271 10 false +SR 5.813,1.219 6.125,1.552 0.313,0.333 10 false *3 4.25,1.917 4.542,2.125 0.292,0.208 10 false *1 6.26,1.927 6.656,2.333 0.396,0.406 10 false *2 4.542,1.938 4.833,2.146 0.292,0.208 10 false F 4.781,1.927 5.073,2.135 0.292,0.208 10 false E 5.146,1.927 5.438,2.135 0.292,0.208 10 false D 5.281,1.927 5.573,2.135 0.292,0.208 10 false C 5.646,1.927 5.938,2.135 0.292,0.208 10 false B 5.906,1.917 6.198,2.125 0.292,0.208 10 false A 1.667,3.417 1.979,3.667 0.313,0.25 10 false +SR 1,3.417 1.313,3.667 0.313,0.25 10 false -SR 5.302,3.417 5.615,3.667 0.313,0.25 10 false +SR 4.625,3.417 4.958,3.667 0.333,0.25 10 false -SR 4.396,2.958 4.813,3.292 0.417,0.333 10 false A30 4.271,2.625 4.604,3.115 0.333,0.49 10 false *b
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Service Wire - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor RH)



b.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-2 (+SR) - A30-1 (-SR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

NG

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)
a.

Disconnect the service wire from connector B.

C284128C08
0.656,1.833 1.01,2.063 0.354,0.229 4.333,1.854 4.677,2.083 0.344,0.229 1.156,2.313 1.396,1.969 true 1.813,2.302 1.583,1.969 true 4.792,2.323 5.031,1.979 true 5.469,2.313 5.24,1.979 true 0.167,0.083 0.51,0.313 0.344,0.229 10 false *A 3.677,0.104 4.052,0.375 0.375,0.271 10 false *B 0.667,0.542 1,0.833 0.333,0.292 10 false *1 2.646,0.771 3.021,1.073 0.375,0.302 10 false *2 0.573,1.448 0.927,1.75 0.354,0.302 10 false *a 4.313,0.552 4.646,0.844 0.333,0.292 10 false *1 6.302,0.552 6.677,0.854 0.375,0.302 10 false *2 2.302,0.552 2.677,0.854 0.375,0.302 10 false A 2.042,0.552 2.417,0.854 0.375,0.302 10 false B 1.677,0.552 2.052,0.854 0.375,0.302 10 false C 1.552,0.552 1.927,0.854 0.375,0.302 10 false D 1.188,0.542 1.563,0.844 0.375,0.302 10 false E 0.938,0.542 1.313,0.844 0.375,0.302 10 false F 0.719,1.865 1.052,2.156 0.333,0.292 10 false A30 4.396,1.885 4.729,2.177 0.333,0.292 10 false A30 5.958,0.552 6.333,0.854 0.375,0.302 10 false A 5.708,0.563 6.083,0.865 0.375,0.302 10 false B 5.333,0.563 5.708,0.865 0.375,0.302 10 false C 5.208,0.563 5.583,0.865 0.375,0.302 10 false D 4.833,0.563 5.208,0.865 0.375,0.302 10 false E 4.594,0.563 4.969,0.865 0.375,0.302 10 false F 1,2.333 1.375,2.604 0.375,0.271 10 false -SR 1.688,2.333 2.094,2.615 0.406,0.281 10 false +SR 4.635,2.333 5.021,2.583 0.385,0.25 10 false -SR 5.344,2.333 5.792,2.594 0.448,0.26 10 false +SR 4.219,1.448 4.573,1.75 0.354,0.302 10 false *a
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-2 (+SR) - A30-1 (-SR) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)
a.

Connect the cable to the negative (-) battery terminal.

C284128C08
0.656,1.833 1.01,2.063 0.354,0.229 4.333,1.854 4.677,2.083 0.344,0.229 1.156,2.313 1.396,1.969 true 1.813,2.302 1.583,1.969 true 4.792,2.323 5.031,1.979 true 5.469,2.313 5.24,1.979 true 0.167,0.083 0.51,0.313 0.344,0.229 10 false *A 3.677,0.104 4.052,0.375 0.375,0.271 10 false *B 0.667,0.542 1,0.833 0.333,0.292 10 false *1 2.646,0.771 3.021,1.073 0.375,0.302 10 false *2 0.573,1.448 0.927,1.75 0.354,0.302 10 false *a 4.313,0.552 4.646,0.844 0.333,0.292 10 false *1 6.302,0.552 6.677,0.854 0.375,0.302 10 false *2 2.302,0.552 2.677,0.854 0.375,0.302 10 false A 2.042,0.552 2.417,0.854 0.375,0.302 10 false B 1.677,0.552 2.052,0.854 0.375,0.302 10 false C 1.552,0.552 1.927,0.854 0.375,0.302 10 false D 1.188,0.542 1.563,0.844 0.375,0.302 10 false E 0.938,0.542 1.313,0.844 0.375,0.302 10 false F 0.719,1.865 1.052,2.156 0.333,0.292 10 false A30 4.396,1.885 4.729,2.177 0.333,0.292 10 false A30 5.958,0.552 6.333,0.854 0.375,0.302 10 false A 5.708,0.563 6.083,0.865 0.375,0.302 10 false B 5.333,0.563 5.708,0.865 0.375,0.302 10 false C 5.208,0.563 5.583,0.865 0.375,0.302 10 false D 4.833,0.563 5.208,0.865 0.375,0.302 10 false E 4.594,0.563 4.969,0.865 0.375,0.302 10 false F 1,2.333 1.375,2.604 0.375,0.271 10 false -SR 1.688,2.333 2.094,2.615 0.406,0.281 10 false +SR 4.635,2.333 5.021,2.583 0.385,0.25 10 false -SR 5.344,2.333 5.792,2.594 0.448,0.26 10 false +SR 4.219,1.448 4.573,1.75 0.354,0.302 10 false *a
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
- -



b.

Turn the ignition switch ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A30-2 (+SR) - Body ground Ignition switch ON Below 1 V
A30-1 (-SR) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)

NG

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C284128C08
0.656,1.833 1.01,2.063 0.354,0.229 4.333,1.854 4.677,2.083 0.344,0.229 1.156,2.313 1.396,1.969 true 1.813,2.302 1.583,1.969 true 4.792,2.323 5.031,1.979 true 5.469,2.313 5.24,1.979 true 0.167,0.083 0.51,0.313 0.344,0.229 10 false *A 3.677,0.104 4.052,0.375 0.375,0.271 10 false *B 0.667,0.542 1,0.833 0.333,0.292 10 false *1 2.646,0.771 3.021,1.073 0.375,0.302 10 false *2 0.573,1.448 0.927,1.75 0.354,0.302 10 false *a 4.313,0.552 4.646,0.844 0.333,0.292 10 false *1 6.302,0.552 6.677,0.854 0.375,0.302 10 false *2 2.302,0.552 2.677,0.854 0.375,0.302 10 false A 2.042,0.552 2.417,0.854 0.375,0.302 10 false B 1.677,0.552 2.052,0.854 0.375,0.302 10 false C 1.552,0.552 1.927,0.854 0.375,0.302 10 false D 1.188,0.542 1.563,0.844 0.375,0.302 10 false E 0.938,0.542 1.313,0.844 0.375,0.302 10 false F 0.719,1.865 1.052,2.156 0.333,0.292 10 false A30 4.396,1.885 4.729,2.177 0.333,0.292 10 false A30 5.958,0.552 6.333,0.854 0.375,0.302 10 false A 5.708,0.563 6.083,0.865 0.375,0.302 10 false B 5.333,0.563 5.708,0.865 0.375,0.302 10 false C 5.208,0.563 5.583,0.865 0.375,0.302 10 false D 4.833,0.563 5.208,0.865 0.375,0.302 10 false E 4.594,0.563 4.969,0.865 0.375,0.302 10 false F 1,2.333 1.375,2.604 0.375,0.271 10 false -SR 1.688,2.333 2.094,2.615 0.406,0.281 10 false +SR 4.635,2.333 5.021,2.583 0.385,0.25 10 false -SR 5.344,2.333 5.792,2.594 0.448,0.26 10 false +SR 4.219,1.448 4.573,1.75 0.354,0.302 10 false *a
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A30-2 (+SR) - Body ground Always 1 MΩ or higher
A30-1 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT AIRBAG SENSOR RH

NG

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR RH
a.
C279500C02
0.156,0.073 0.552,0.375 0.396,0.302 10 false *A 0.198,2.365 0.573,2.688 0.375,0.323 10 false *B 0.49,0.938 0.833,1.208 0.344,0.271 10 false *1 2.625,3.479 2.948,3.792 0.323,0.313 10 false *2 2.604,1.24 2.948,1.51 0.344,0.271 10 false *2 2.177,0.958 2.521,1.229 0.344,0.271 10 false A 2.021,0.958 2.365,1.229 0.344,0.271 10 false B 1.573,0.958 1.917,1.229 0.344,0.271 10 false C 1.417,0.958 1.76,1.229 0.344,0.271 10 false D 0.969,0.958 1.313,1.229 0.344,0.271 10 false E 0.813,0.958 1.156,1.229 0.344,0.271 10 false F 2.177,3.458 2.521,3.729 0.344,0.271 10 false A 2.021,3.458 2.365,3.729 0.344,0.271 10 false B 1.573,3.458 1.917,3.729 0.344,0.271 10 false C 1.417,3.458 1.76,3.729 0.344,0.271 10 false D 0.969,3.458 1.313,3.729 0.344,0.271 10 false E 0.823,3.458 1.167,3.729 0.344,0.271 10 false F 0.49,3.458 0.833,3.729 0.344,0.271 10 false *1
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the front airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348324C03
1.042,1.792 1.385,2.01 0.344,0.219 4.635,1.813 4.979,2.031 0.344,0.219 1.344,0.854 1.344,0.521 false 4.917,0.969 4.917,0.635 false 1.969,0.396 1.969,0.146 1.969,0.146 1.802,0.146 false 5.542,0.51 5.542,0.26 5.542,0.26 5.375,0.26 false 1.458,2.396 1.792,2 true 2.354,2.406 2,2 true 5.031,2.396 5.365,2 true 5.948,2.406 5.594,2 true 0.083,0.083 0.667,0.333 0.583,0.25 10 false *A 3.667,0.083 4.146,0.323 0.479,0.24 10 false *B 0.604,0.375 1,0.708 0.396,0.333 10 false *1 1.271,0.865 1.667,1.198 0.396,0.333 10 false *3 1,1.333 1.417,1.667 0.417,0.333 10 false *a 4.188,0.49 4.583,0.823 0.396,0.333 10 false *1 2.667,0.604 3.146,1.01 0.479,0.406 10 false *2 6.25,0.49 6.646,0.74 0.396,0.25 10 false *2 4.854,0.979 5.25,1.313 0.396,0.333 10 false *3 1.646,0.073 2.063,0.396 0.417,0.323 10 false *4 5.219,0.188 5.635,0.51 0.417,0.323 10 false *4 4.583,1.333 5,1.667 0.417,0.333 10 false *a 1.094,1.823 1.51,2.156 0.417,0.333 10 false AF5 4.688,1.844 5.104,2.177 0.417,0.333 10 false AF5 1.281,2.417 1.698,2.75 0.417,0.333 10 false +SR 2.219,2.417 2.635,2.75 0.417,0.333 10 false -SR 4.854,2.417 5.271,2.75 0.417,0.333 10 false +SR 5.813,2.417 6.229,2.75 0.417,0.333 10 false -SR 2.354,0.385 2.833,0.792 0.479,0.406 10 false A 2.104,0.385 2.583,0.792 0.479,0.406 10 false B 1.74,0.385 2.219,0.792 0.479,0.406 10 false C 1.479,0.385 1.958,0.792 0.479,0.406 10 false D 1.115,0.385 1.594,0.792 0.479,0.406 10 false E 0.854,0.385 1.333,0.792 0.479,0.406 10 false F 5.938,0.5 6.333,0.75 0.396,0.25 10 false A 5.688,0.5 6.083,0.75 0.396,0.25 10 false B 5.313,0.5 5.708,0.75 0.396,0.25 10 false C 5.063,0.5 5.458,0.75 0.396,0.25 10 false D 4.698,0.5 5.094,0.75 0.396,0.25 10 false E 4.448,0.5 4.844,0.75 0.396,0.25 10 false F
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-4 (+SR) - Body ground Always 1 MΩ or higher
AF5-3 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348324C03
1.042,1.792 1.385,2.01 0.344,0.219 4.635,1.813 4.979,2.031 0.344,0.219 1.344,0.854 1.344,0.521 false 4.917,0.969 4.917,0.635 false 1.969,0.396 1.969,0.146 1.969,0.146 1.802,0.146 false 5.542,0.51 5.542,0.26 5.542,0.26 5.375,0.26 false 1.458,2.396 1.792,2 true 2.354,2.406 2,2 true 5.031,2.396 5.365,2 true 5.948,2.406 5.594,2 true 0.083,0.083 0.667,0.333 0.583,0.25 10 false *A 3.667,0.083 4.146,0.323 0.479,0.24 10 false *B 0.604,0.375 1,0.708 0.396,0.333 10 false *1 1.271,0.865 1.667,1.198 0.396,0.333 10 false *3 1,1.333 1.417,1.667 0.417,0.333 10 false *a 4.188,0.49 4.583,0.823 0.396,0.333 10 false *1 2.667,0.604 3.146,1.01 0.479,0.406 10 false *2 6.25,0.49 6.646,0.74 0.396,0.25 10 false *2 4.854,0.979 5.25,1.313 0.396,0.333 10 false *3 1.646,0.073 2.063,0.396 0.417,0.323 10 false *4 5.219,0.188 5.635,0.51 0.417,0.323 10 false *4 4.583,1.333 5,1.667 0.417,0.333 10 false *a 1.094,1.823 1.51,2.156 0.417,0.333 10 false AF5 4.688,1.844 5.104,2.177 0.417,0.333 10 false AF5 1.281,2.417 1.698,2.75 0.417,0.333 10 false +SR 2.219,2.417 2.635,2.75 0.417,0.333 10 false -SR 4.854,2.417 5.271,2.75 0.417,0.333 10 false +SR 5.813,2.417 6.229,2.75 0.417,0.333 10 false -SR 2.354,0.385 2.833,0.792 0.479,0.406 10 false A 2.104,0.385 2.583,0.792 0.479,0.406 10 false B 1.74,0.385 2.219,0.792 0.479,0.406 10 false C 1.479,0.385 1.958,0.792 0.479,0.406 10 false D 1.115,0.385 1.594,0.792 0.479,0.406 10 false E 0.854,0.385 1.333,0.792 0.479,0.406 10 false F 5.938,0.5 6.333,0.75 0.396,0.25 10 false A 5.688,0.5 6.083,0.75 0.396,0.25 10 false B 5.313,0.5 5.708,0.75 0.396,0.25 10 false C 5.063,0.5 5.458,0.75 0.396,0.25 10 false D 4.698,0.5 5.094,0.75 0.396,0.25 10 false E 4.448,0.5 4.844,0.75 0.396,0.25 10 false F
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)
- -



b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AF5-4 (+SR) - Body ground Ignition switch ON Below 1 V
AF5-3 (-SR) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348324C03
1.042,1.792 1.385,2.01 0.344,0.219 4.635,1.813 4.979,2.031 0.344,0.219 1.344,0.854 1.344,0.521 false 4.917,0.969 4.917,0.635 false 1.969,0.396 1.969,0.146 1.969,0.146 1.802,0.146 false 5.542,0.51 5.542,0.26 5.542,0.26 5.375,0.26 false 1.458,2.396 1.792,2 true 2.354,2.406 2,2 true 5.031,2.396 5.365,2 true 5.948,2.406 5.594,2 true 0.083,0.083 0.667,0.333 0.583,0.25 10 false *A 3.667,0.083 4.146,0.323 0.479,0.24 10 false *B 0.604,0.375 1,0.708 0.396,0.333 10 false *1 1.271,0.865 1.667,1.198 0.396,0.333 10 false *3 1,1.333 1.417,1.667 0.417,0.333 10 false *a 4.188,0.49 4.583,0.823 0.396,0.333 10 false *1 2.667,0.604 3.146,1.01 0.479,0.406 10 false *2 6.25,0.49 6.646,0.74 0.396,0.25 10 false *2 4.854,0.979 5.25,1.313 0.396,0.333 10 false *3 1.646,0.073 2.063,0.396 0.417,0.323 10 false *4 5.219,0.188 5.635,0.51 0.417,0.323 10 false *4 4.583,1.333 5,1.667 0.417,0.333 10 false *a 1.094,1.823 1.51,2.156 0.417,0.333 10 false AF5 4.688,1.844 5.104,2.177 0.417,0.333 10 false AF5 1.281,2.417 1.698,2.75 0.417,0.333 10 false +SR 2.219,2.417 2.635,2.75 0.417,0.333 10 false -SR 4.854,2.417 5.271,2.75 0.417,0.333 10 false +SR 5.813,2.417 6.229,2.75 0.417,0.333 10 false -SR 2.354,0.385 2.833,0.792 0.479,0.406 10 false A 2.104,0.385 2.583,0.792 0.479,0.406 10 false B 1.74,0.385 2.219,0.792 0.479,0.406 10 false C 1.479,0.385 1.958,0.792 0.479,0.406 10 false D 1.115,0.385 1.594,0.792 0.479,0.406 10 false E 0.854,0.385 1.333,0.792 0.479,0.406 10 false F 5.938,0.5 6.333,0.75 0.396,0.25 10 false A 5.688,0.5 6.083,0.75 0.396,0.25 10 false B 5.313,0.5 5.708,0.75 0.396,0.25 10 false C 5.063,0.5 5.458,0.75 0.396,0.25 10 false D 4.698,0.5 5.094,0.75 0.396,0.25 10 false E 4.448,0.5 4.844,0.75 0.396,0.25 10 false F
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-4 (+SR) - AF5-3 (-SR) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C348325C02
1.135,0.49 1.458,0.688 0.323,0.198 0.781,2.833 1.125,3.031 0.344,0.198 4.698,0.49 5.031,0.688 0.333,0.198 4.375,2.802 4.708,3.01 0.333,0.208 1.365,2.125 1.365,1.875 false 1.979,1.75 1.979,1.5 1.979,1.5 1.813,1.5 false 4.948,2.271 4.948,2.021 false 5.552,1.896 5.552,1.646 5.552,1.646 5.385,1.646 false 1.115,3.406 1.448,3.115 true 1.99,3.406 1.635,3.115 true 4.698,3.406 5.052,3.125 true 5.563,3.406 5.219,3.125 true 2.25,1.188 2.25,1.031 false 5.844,1.188 5.844,1.031 false 1.896,1.083 2.177,0.802 true 2.615,1.073 2.333,0.813 true 5.479,1.094 5.76,0.813 true 6.208,1.083 5.927,0.823 true 0.167,0.083 0.75,0.5 0.583,0.417 10 false *A 3.75,0.083 4.417,0.417 0.667,0.333 10 false *B 0.625,1.729 1.021,2.063 0.396,0.333 10 false *1 2.646,1.958 3.063,2.292 0.417,0.333 10 false *2 1.292,2.135 1.688,2.469 0.396,0.333 10 false *3 1.656,1.427 2.135,1.844 0.479,0.417 10 false *4 2.177,1.198 2.521,1.438 0.344,0.24 10 false *5 1.083,0.25 1.417,0.583 0.333,0.333 10 false *a 0.688,2.563 1.083,2.948 0.396,0.385 10 false *b 4.219,1.875 4.615,2.208 0.396,0.333 10 false *1 6.271,1.875 6.688,2.208 0.417,0.333 10 false *2 4.875,2.281 5.271,2.615 0.396,0.333 10 false *3 5.229,1.573 5.563,2.063 0.333,0.49 10 false *4 5.781,1.198 6.125,1.5 0.344,0.302 10 false *5 4.667,0.25 5,0.583 0.333,0.333 10 false *a 4.281,2.563 4.677,2.948 0.396,0.385 10 false *b 2.375,1.729 2.792,2.063 0.417,0.333 10 false A 2.125,1.729 2.542,2.063 0.417,0.333 10 false B 1.75,1.729 2.167,2.063 0.417,0.333 10 false C 1.5,1.729 1.917,2.063 0.417,0.333 10 false D 1.135,1.729 1.552,2.063 0.417,0.333 10 false E 0.885,1.729 1.302,2.063 0.417,0.333 10 false F 1.188,0.51 1.604,0.917 0.417,0.406 10 false F70 4.76,0.51 5.177,0.917 0.417,0.406 10 false F70 0.948,3.417 1.365,3.75 0.417,0.333 10 false +SR 4.427,2.823 4.844,3.229 0.417,0.406 10 false AF5 1.875,3.417 2.292,3.698 0.417,0.281 10 false -SR 4.531,3.417 4.948,3.771 0.417,0.354 10 false +SR 5.458,3.417 5.875,3.688 0.417,0.271 10 false -SR 0.833,2.854 1.25,3.26 0.417,0.406 10 false AF5 5.958,1.885 6.375,2.219 0.417,0.333 10 false A 5.708,1.885 6.125,2.219 0.417,0.333 10 false B 5.333,1.885 5.75,2.219 0.417,0.333 10 false C 5.083,1.885 5.5,2.219 0.417,0.333 10 false D 4.719,1.885 5.135,2.219 0.417,0.333 10 false E 4.469,1.885 4.885,2.219 0.417,0.333 10 false F 2.49,1.083 2.906,1.417 0.417,0.333 10 false +SR 1.75,1.083 2.167,1.365 0.417,0.281 10 false -SR 6.073,1.083 6.49,1.417 0.417,0.333 10 false +SR 5.333,1.083 5.75,1.365 0.417,0.281 10 false -SR
*A w/o Dual-stage SRS *B w/ Dual-stage SRS
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Service Wire - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)


HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF5-4 (+SR) - AF5-3 (-SR) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE