Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1625/22  Side Airbag Sensor LH Circuit Malfunction  


DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH.

The door side airbag sensor LH, No. 1 side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

DTC B1625/22 is stored when a malfunction is detected in the No. 1 side airbag sensor LH.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1625/22 Side Airbag Sensor LH Circuit Malfunction Any of the following conditions is met:
·

No. 1 side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

No. 1 side airbag sensor LH

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Malfunction Status No. 1 side airbag sensor LH malfunction ○ -
Airbag sensor assembly malfunction - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK NO. 1 SIDE AIRBAG SENSOR LH
a.
C313482C01
0.125,0.135 0.573,0.438 0.448,0.302 10 false *A 0.208,2.406 0.615,2.802 0.406,0.396 10 false *B 0.729,1.052 1.115,1.385 0.385,0.333 10 false *1 0.729,3.156 1.115,3.49 0.385,0.333 10 false *1 2.365,1.073 2.729,1.438 0.365,0.365 10 false *2 2.365,3.469 2.729,3.833 0.365,0.365 10 false *2 1.896,1.063 2.26,1.427 0.365,0.365 10 false A 1.74,1.063 2.104,1.427 0.365,0.365 10 false B 1.271,1.063 1.635,1.427 0.365,0.365 10 false C 1.115,1.063 1.479,1.427 0.365,0.365 10 false D 1.896,3.167 2.26,3.531 0.365,0.365 10 false A 1.74,3.167 2.104,3.531 0.365,0.365 10 false B 1.271,3.167 1.531,3.542 0.26,0.375 10 false C 1.115,3.167 1.375,3.542 0.26,0.375 10 false D
*A w/o Dual-stage SRS
*B w/ Dual-stage SRS
*1 No. 1 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the No. 1 side airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1620/21 and B1625/22 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1625/22 is output. A
DTC B1620/21 is output. B
DTCs B1620/21 and B1625/22 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 1 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C