Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › ENGINE UNIT
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0294289 ENGINE UNIT G

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.


Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Only use clean engine oil.



A293105C19
1.583,0.302 1.969,0.302 false 2.344,0.302 2.802,0.302 false 1.448,0.958 2.052,0.698 true 2.313,0.698 2.896,0.865 true 1.5,1.125 2.063,0.938 false 2.302,0.938 2.833,1.083 false 1.385,1.406 2.052,1.229 true 2.313,1.219 2.938,1.365 true 1.302,1.99 2.052,1.583 true 2.323,1.573 3.042,1.969 true 1.469,2.115 2.063,1.958 true 2.323,1.958 2.875,2.104 true 4.698,1.104 5.052,1.354 false 2.115,0.844 2.427,1.073 0.313,0.229 10 false *f 2.115,1.469 2.427,1.677 0.313,0.208 10 false *g 2.125,0.594 2.438,0.75 0.313,0.156 10 false *c 2.115,1.135 2.427,1.292 0.313,0.156 10 false *d 2.115,1.865 2.427,2.021 0.313,0.156 10 false *e 2.052,0.229 2.51,0.427 0.458,0.198 10 false SST 4.542,0.938 5,1.135 0.458,0.198 10 false SST 1.198,0.188 1.51,0.385 0.313,0.198 10 false *a 2.979,0.177 3.292,0.375 0.313,0.198 10 false *b
*a Correct *b Incorrect
*c Taper *d Low Pressure Chamber
*e High Pressure Chamber *f Plunger
*g Check Ball - -


a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 13506 3.INSPECT CHAIN SUB-ASSEMBLY

a.
A386378C05
1.698,0.979 2.01,1.177 0.313,0.198 10 false *a 0.979,2.021 1.177,2.177 0.198,0.156 10 false 0 1.385,2.021 1.573,2.177 0.188,0.156 10 false 1 1.979,2.021 2.198,2.177 0.219,0.156 10 false 14 2.396,2.021 2.615,2.177 0.219,0.156 10 false 15
*a Measurement Length


Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

115.2 mm (4.54 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


HINT:

If the average elongation is more than the maximum, replace the chain sub-assembly.



Hide 13507 4.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A386378C05
1.698,0.979 2.01,1.177 0.313,0.198 10 false *a 0.979,2.021 1.177,2.177 0.198,0.156 10 false 0 1.385,2.021 1.573,2.177 0.188,0.156 10 false 1 1.979,2.021 2.198,2.177 0.219,0.156 10 false 14 2.396,2.021 2.615,2.177 0.219,0.156 10 false 15
*a Measurement Length


Using a spring scale, pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

102.1 mm (4.02 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


HINT:

If the average elongation is more than the maximum, replace the No. 2 chain sub-assembly.



Hide 13519 5.INSPECT OIL PUMP DRIVE GEAR

a.
A053035

Place the No. 2 chain sub-assembly around the oil pump drive gear.


b.

Using a vernier caliper, measure the diameter of the oil pump drive gear and No. 2 chain sub-assembly.

Minimum Gear Diameter (with No. 2 Chain Sub-assembly):

48.2 mm (1.90 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive gear.



Hide 15163 6.INSPECT OIL PUMP DRIVE SHAFT GEAR

a.
A053036

Place the No. 2 chain sub-assembly around the oil pump drive shaft gear.


b.

Using a vernier caliper, measure the diameter of the oil pump drive shaft gear and No. 2 chain sub-assembly.

Minimum Gear Diameter (with No. 2 Chain Sub-assembly):

48.2 mm (1.90 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and oil pump drive shaft gear.



Hide 13050 7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A063864

Place the chain sub-assembly around the camshaft timing gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain sub-assembly.

Minimum Gear Diameter (with Chain Sub-assembly):

96.8 mm (3.81 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.



Hide 8.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A150911

Place the chain sub-assembly around the camshaft timing exhaust gear assembly.


b.

Using a vernier caliper, measure the diameter of the camshaft timing exhaust gear assembly and chain sub-assembly.

Minimum Gear Diameter (with Chain Sub-assembly):

96.8 mm (3.81 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing exhaust gear assembly.



Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A053035

Place the chain sub-assembly around the crankshaft timing sprocket.


b.

Using a vernier caliper, measure the diameter of the crankshaft timing sprocket and chain sub-assembly.

Minimum Gear Diameter (with Chain Sub-assembly):

51.1 mm (2.01 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.



Hide 13559 10.INSPECT CHAIN TENSIONER SLIPPER

a.
A150912C05
3.063,0.865 3.375,1.021 0.313,0.156 10 false *a
*a Depth


Using a vernier caliper, measure the chain tensioner slipper wear depth.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper.



Hide 13561 11.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A173603C02
2.958,0.979 3.271,1.135 0.313,0.156 10 false *a
*a Depth


Using a vernier caliper, measure the No. 1 chain vibration damper wear depth.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 1 chain vibration damper.



Hide 13549 12.INSPECT CHAIN TENSIONER PLATE

a.
A126893C05
2.969,1.385 3.281,1.542 0.313,0.156 10 false *a
*a Depth


Using a vernier caliper, measure the chain tensioner plate wear depth.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner plate.



Hide 13540 13.INSPECT NO. 1 CHAIN TENSIONER

a.
A146263C04
0.751,0.522 0.928,0.683 0.177,0.161 10 *a 0.305,1.036 0.467,1.193 0.162,0.157 10 *b 1.251,1.382 1.436,1.556 0.185,0.174 10 *c
*a Raise
*b Move
*c Lock


Check that the plunger moves smoothly when the cam is raised with your finger.


b.

Release the cam, then check that the plunger is locked in place by the cam and does not move when pushed with your finger.

HINT:

If necessary, replace the No. 1 chain tensioner.



Hide 11101A 14.INSPECT CYLINDER HEAD SET BOLT

a.
A209191C14
1.667,1.052 1.927,1.24 0.26,0.188 10 false *a 2.135,1.656 3.177,1.844 1.042,0.188 10 false *b 1.406,2.781 2,2.969 0.594,0.188 10 false *c
*a Measurement Length
*b Measuring Area
*c 115 mm (4.53 in.)


Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Standard Length:

146.8 to 148.2 mm (5.78 to 5.83 in.)


Maximum Length:

149.2 mm (5.87 in.)


NOTICE:
·

If the length is greater than the maximum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.




b.

Using a vernier caliper, measure the diameter of the threads at several points within the area shown in the illustration.

Standard Diameter:

9.77 to 9.96 mm (0.3846 to 0.3921 in.)


Minimum Diameter:

9.4 mm (0.3701 in.)


NOTICE:
·

Diameter measurements should be done at several points.

·

If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.




Hide 17141 15.INSPECT EXHAUST MANIFOLD

a.
A158847

Using a precision straightedge and feeler gauge, measure the warpage on the surface that contacts the cylinder head sub-assembly.

Maximum Warpage:

0.7 mm (0.0276 in.)


HINT:

If the warpage is more than the maximum, replace the exhaust manifold.