Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › CYLINDER HEAD
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0294290 CYLINDER HEAD A

3ZR-FAE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A150967E01
0.142,0.058 0.448,0.216 0.306,0.159 10 SST 1.342,0.635 0.5,0.164 0.5,0.164 1.231,1.197 false

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
C267780

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)


Select a new intake valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:
·

If the intake valve guide bush bore diameter is more than 10.306 mm (0.4057 in.), machine the intake valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 intake valve guide bush.

·

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.4077 in.), replace the cylinder head sub-assembly.




e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A150969C03
0.19,0.196 0.683,0.517 0.493,0.321 10 SST 2.886,0.597 3.07,0.764 0.184,0.167 10 *a 1.346,0.624 0.48,0.301 0.48,0.301 1.215,1.276 false
*a Protrusion Height


Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.9 to 10.3 mm (0.390 to 0.406 in.)



h.
A150971

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the specified clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A150968E01
1.522,1.759 1.843,1.908 0.320,0.149 10 SST 2.063,0.83 1.751,1.749 1.751,1.749 2.222,1.192 false

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A152650N01
0.609,0.812 0.705,0.787 false 0.68,0.778 0.739,0.805 0.059,0.027 0.567,0.795 0.627,0.821 0.06,0.026

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)


Select a new exhaust valve guide bush (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


HINT:
·

If the exhaust valve guide bush bore diameter is more than 10.306 mm (0.4057 in.), machine the exhaust valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 exhaust valve guide bush.

·

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.4077 in.), replace the cylinder head sub-assembly.




e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A150970C03
1.938,0.552 1.521,0.552 1.521,0.552 2.188,1.135 false 1.24,0.479 1.583,0.698 0.344,0.219 10 SST 0.656,0.698 0.885,0.854 0.229,0.156 10 *a
*a Protrusion Height


Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

11.15 to 11.55 mm (0.4390 to 0.4547 in.)



h.
A150972

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the specified oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE SPARK PLUG TUBE

NOTICE:

When using a new cylinder head sub-assembly, the spark plug tubes must be replaced.


a.
A211988C12
1.677,1.708 1.854,1.865 0.177,0.156 10 false *b 1.844,0.26 2.01,0.417 0.167,0.156 10 false *a
*a 1.0 to 3.0 mm (0.0394 to 0.118 in.)
*b 1.0 to 13.0 mm (0.0394 to 0.5118 in.)


Apply adhesive to a new spark plug tube as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.


Standard Application Width:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes of applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the adhesive to engine oil for at least 1 hour after installing the spark plug tube.




b.
A205906C10
2.365,3.146 2.552,3.323 0.188,0.177 10 false *a
*a 122 mm (4.80 in.)


Using a wooden block and hammer, tap in the spark plug tube.

Standard Protrusion Height:

122 mm (4.80 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 11155A 4.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A150959C13
0.333,0.063 0.542,0.26 0.208,0.198 12 false *a 1.573,3.698 1.76,3.854 0.188,0.156 10 false *d 0.792,2.5 1.01,2.76 0.219,0.26 10 false *b 1.302,3.021 1.552,3.219 0.25,0.198 10 false *c
*a Top Side
*b Width
*c Height
*d Protrusion Height


Using a plastic hammer, tap in 2 new ring pins.

Standard Ring Pin:
Item Height Width Protrusion
Ring pin 11.7 to 12.3 mm (0.461 to 0.484 in.) 12.0 mm (0.472 in.) 6.5 to 7.5 mm (0.256 to 0.295 in.)