Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › CYLINDER HEAD
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0294290 CYLINDER HEAD G

3ZR-FAE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER HEAD FOR FLATNESS

a.

Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder block sub-assembly and manifolds.

A270932C01
2.906,0.583 3.219,0.74 0.313,0.156 10 *a 5.208,0.594 5.521,0.75 0.313,0.156 10 *b 5.208,1.573 5.521,1.729 0.313,0.156 10 *c
*a Bottom Side *b Intake Manifold Side
*c Exhaust Manifold Side - -


Maximum Warpage:
Item Specified Condition
Bottom side 0.05 mm (0.00197 in.)
Intake manifold side 0.10 mm (0.00394 in.)
Exhaust manifold side 0.10 mm (0.00394 in.)


HINT:

If the warpage is more than the maximum, replace the cylinder head sub-assembly.



Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.

Using a dye penetrant, check the intake ports, exhaust ports and bottom surface of the cylinder head sub-assembly for cracks.

HINT:

If cracks are found, replace the cylinder head sub-assembly.



Hide 13711 3.INSPECT INTAKE VALVE

a.
A121380C28
1.79,0.949 1.985,1.129 0.196,0.180 10 *a
*a Overall Length


Using a vernier caliper, measure the valve overall length.

Standard Overall Length:

109.34 mm (4.30 in.)


Minimum Overall Length:

108.84 mm (4.29 in.)


HINT:

If the overall length is less than the minimum, replace the intake valve.



b.
A121378

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)


HINT:

If the diameter is not as specified, check the oil clearance.



c.
A146308C06
0.406,1.771 0.729,1.948 0.323,0.177 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


HINT:

If the margin thickness is less than the minimum, replace the intake valve.



Hide 13715 4.INSPECT EXHAUST VALVE

a.
A121383C23
1.792,1 2.135,1.156 0.344,0.156 10 *a
*a Overall Length


Using a vernier caliper, measure the valve overall length.

Standard Overall Length:

108.25 mm (4.26 in.)


Minimum Overall Length:

107.75 mm (4.24 in.)


HINT:

If the overall length is less than the minimum, replace the exhaust valve.



b.
A121381

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)


HINT:

If the diameter is not as specified, check the oil clearance.



c.
A121382C10
0.438,1.865 0.708,2.146 0.271,0.281 10 *a
*a Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)


Minimum Margin Thickness:

0.5 mm (0.0197 in.)


HINT:

If the margin thickness is less than the minimum, replace the exhaust valve.



Hide 13711B 5.INSPECT INNER COMPRESSION SPRING

a.
A314490

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:

51.88 mm (2.042 in.) or 51.90 mm (2.043 in.)


NOTICE:

Inner compression springs come in 2 different lengths. Make sure all inner compression springs are the same length when replacing them.


HINT:

If the free length is not as specified, replace the inner compression spring.



b.
A319225C40
1.448,0.396 1.76,0.552 0.313,0.156 10 false *1 0.979,1.406 1.313,1.615 0.333,0.208 10 false *a
*1 Deviation
*a 37.5 mm (1.48 in.)


Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.3 mm (0.0512 in.)


HINT:

If the deviation is more than the maximum, replace the inner compression spring.



Hide 6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A150966

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.080 mm (0.00315 in.)
Exhaust 0.085 mm (0.00335 in.)


HINT:
·

Oil clearance = Inside diameter - Valve stem diameter

·

If the oil clearance is more than the maximum, replace the valve and valve guide bush.




Hide 7.INSPECT INTAKE VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.
A146287C06
2.938,1.281 3.271,1.594 0.333,0.313 10 *a
*a Width


Check the valve face and intake valve seat by using the following procedure:

i.

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the intake valve.


ii.

If Prussian blue appears around the entire intake valve seat, the intake valve seat and valve face are concentric. If not, resurface the intake valve seat.


iii.

Check that the intake valve seat contacts the middle of the valve face with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).



Hide 8.INSPECT EXHAUST VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

HINT:

Do not rotate the valve while pressing the valve.



c.
A146287C06
2.938,1.281 3.271,1.594 0.333,0.313 10 *a
*a Width


Check the valve face and exhaust valve seat by using the following procedure:

i.

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the exhaust valve.


ii.

If Prussian blue appears around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric. If not, resurface the exhaust valve seat.


iii.

Check that the exhaust valve seat contacts the middle of the valve face with the width between 1.0 and 1.4 mm (0.0394 and 0.0551 in.).