Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0294291 CYLINDER BLOCK A

3ZR-FAE ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.
A151025C05
0.094,0.135 0.969,0.323 0.875,0.188 10 *a 0.688,2.927 1.094,3.292 0.406,0.365 10 *b 3.01,3.271 3.24,3.51 0.229,0.24 10 *d 1.333,3.542 1.781,3.906 0.448,0.365 10 *c
*a Upper Side
*b Width
*c Height
*d Protrusion Height


Using a plastic hammer, tap in the ring pins.

Standard Ring Pin:
Item Height Width Protrusion
Ring Pin 14.3 to 14.7 mm (0.563 to 0.579 in.) 12.9 to 13.0 mm (0.508 to 0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)



Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.

Using a plastic hammer, tap in the straight pins.

A315710C01
2.302,1.167 2.667,0.833 2.667,0.833 2.833,0.833 true 0.75,1.167 0.917,1.167 0.917,1.167 1.542,1.823 true 0.583,1.667 0.75,1.667 0.75,1.667 1.292,2.042 true 3.833,1.167 4,1.167 4,1.167 4.344,0.875 true 6.354,1.885 6.667,1.583 6.667,1.583 6.833,1.583 true 0.75,3.167 0.917,3.167 0.917,3.167 1.229,3.479 true 2.688,3.323 2.917,3.083 2.917,3.083 3.083,3.083 true 4,2.917 4.167,2.917 4.167,2.917 4.417,3.104 true 3.917,4 4.083,4 4.083,4 4.729,3.573 true 0.583,0.094 0.896,0.25 0.313,0.156 10 false *a 3.833,0.083 4.146,0.24 0.313,0.156 10 false *b 0.604,2.5 0.917,2.656 0.313,0.156 10 false *c 3.854,2.5 4.167,2.656 0.313,0.156 10 false *d 2.042,5.26 2.354,5.417 0.313,0.156 10 false *e 2.521,4.677 2.833,4.833 0.313,0.156 10 false *f 5.24,4.635 5.552,4.792 0.313,0.156 10 false *g 2.875,0.771 3.031,0.969 0.156,0.198 10 false B 0.635,1.104 0.792,1.302 0.156,0.198 10 false A 0.479,1.604 0.635,1.802 0.156,0.198 10 false B 3.708,1.104 3.865,1.302 0.156,0.198 10 false C 6.875,1.521 7.031,1.719 0.156,0.198 10 false C 0.625,3.104 0.781,3.302 0.156,0.198 10 false D 3.125,3.021 3.281,3.219 0.156,0.198 10 false D 3.885,2.854 4.042,3.052 0.156,0.198 10 false E 3.813,3.938 3.969,4.135 0.156,0.198 10 false E
*a Front Side *b Lower Side
*c Rear Side *d LH Side
*e Width *f Height
*g Protrusion Height - -


Standard Straight Pin:
Item Height Width Protrusion
Pin A 36 mm (1.42 in.) 10 mm (0.394 in.) 18.5 to 19.5 mm (0.728 to 0.768 in.)
Pin B 12 mm (0.472 in.) 4 mm (0.157 in.) 5.0 to 7.0 mm (0.197 to 0.276 in.)
Pin C 18 mm (0.709 in.) 8 mm (0.315 in.) 8 to 10 mm (0.315 to 0.394 in.)
Pin D 22 mm (0.866 in.) 10 mm (0.394 in.) 11 to 13 mm (0.433 to 0.512 in.)
Pin E 12 mm (0.472 in.) 4 mm (0.157 in.) 5.0 to 6.0 mm (0.197 to 0.236 in.)



Hide 3.REPLACE STUD BOLT

NOTICE:

If the stud bolt is deformed or the threads are damaged, replace it.


HINT:

This procedure is for type A.


a.

Using an E6 "TORX" socket wrench, remove the stud bolts.


b.
A205577C02
2.094,3.448 2.292,3.615 0.198,0.167 10 *b 2.094,3.927 2.281,4.115 0.188,0.188 10 *c 2.594,3.656 2.833,3.865 0.24,0.208 10 *d 0.104,0.073 0.792,0.271 0.688,0.198 10 *a
*a LH Side
*b 16 mm (0.630 in.)
*c 9 mm (0.354 in.)
*d 27 mm (1.063 in.)


Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 13201A 4.REPLACE CONNECTING ROD SMALL END BUSH

a.
A132154E03
0.644,0.325 0.967,0.495 0.323,0.17 10 SST 1.022,0.414 1.143,0.416 1.143,0.416 1.521,0.654 false

Using SST and a press, press out the connecting rod small end bush.

SST
09222-30010  


b.
A132157C09
2.156,0.844 2.698,1.24 2.698,1.24 2.229,1.667 false 2.76,1.156 3.292,1.323 0.531,0.167 10 false *a
*a Oil Hole


Align the oil holes of a new connecting rod small end bush and the connecting rod.


c.
A132154E02
0.644,0.325 0.967,0.495 0.323,0.17 10 SST 1.022,0.414 1.143,0.416 1.143,0.416 1.521,0.654 false

Using SST and a press, press in the connecting rod small end bush.

SST
09222-30010  


d.
A132159

Using a pin hole grinder, hone the connecting rod small end bush to obtain the standard oil clearance between the connecting rod small end bush and piston pin.

Standard Oil Clearance:

-0.001 to 0.005 mm (-0.0000394 to 0.0001968 in.)



e.
A132160

Coat the piston pin with engine oil. Push the piston pin into the connecting rod with your thumb to check that the piston pin fits at normal room temperature.