Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0294291 CYLINDER BLOCK A

3ZR-FAE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the piston or piston ring.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 15708 1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A151001

Using a 5 mm hexagon socket wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 2.INSTALL PISTON

a.
A151020C10
1.125,1.219 2.146,1.646 2.146,1.646 2.146,1.229 false 2.115,1.688 2.344,1.917 0.229,0.229 10 *a
*a Cutout


Using a screwdriver, install a new snap ring at one end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the cutout of the piston.



b.

Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).


c.
A311991C01
2.229,3.135 2.833,2.042 false 1.188,0.792 1.521,0.219 1.521,0.219 1.74,0.219 false 1.396,2.365 2.24,3.135 2.24,3.135 2.833,2.771 false 2.146,3.167 2.458,3.365 0.313,0.198 10 false *a 1.823,0.125 2.135,0.323 0.313,0.198 10 false *a
*a Front Mark


Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the piston pin comes into contact with the snap ring.

HINT:

The piston and piston pin are a matched set.



d.

Using a screwdriver, install a new snap ring on the other end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the cutout of the piston.



e.
A152651

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.

HINT:

Perform "Inspection After Repair" after replacing the piston.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13011 3.INSTALL PISTON RING SET

a.
A318878C01
2.344,0.635 2.635,0.417 false 0.656,1.094 1.073,1.094 false 2.354,1.542 2.656,1.813 false 2.688,0.323 3,0.479 0.313,0.156 10 false *1 0.469,1.042 0.781,1.198 0.313,0.156 10 false *2 2.667,1.823 2.979,1.979 0.313,0.156 10 false *3
*1 Upper Side Rail
*2 Oil Ring Expander
*3 Lower Side Rail


Install the oil ring expander and 2 side rails by hand.

NOTICE:

When installing the upper side rail and lower side rail, the ends of the oil ring expander may overlap. If it occurs, the upper side rail or lower side rail may move out of its groove.



b.

Check that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

A321517C02
3.542,0.885 3.854,1.083 0.313,0.198 10 false *c 1.531,0.708 1.844,0.906 0.313,0.198 10 false *a 3.563,2.344 3.875,2.542 0.313,0.198 10 false *d 4.229,1.813 4.542,2.01 0.313,0.198 10 false *b
*a Press around the circumference *b Ring End
*c Correct *d Incorrect (Ends of the oil ring expander are overlapping)


NOTICE:
·

After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.

·

If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.

·

If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.




c.
A289030C07
1.208,2.615 1.667,2.135 1.667,2.135 1.885,2.135 true 1.083,4.26 1.083,4.427 false 2.313,4.26 2.313,4.427 false 1.75,3.531 1.521,3.542 1.521,3.542 1.146,3.219 true 2.229,0.49 2.656,0.323 false 1.375,2.615 1.979,2.427 1.979,2.427 2.198,2.427 true 1.385,3.198 1.99,3.01 1.99,3.01 2.208,3.01 true 0.344,2.948 0.698,3.292 0.354,0.344 10 false *1 0.354,3.531 0.729,3.802 0.375,0.271 10 false *2 1.948,2.031 2.406,2.406 0.458,0.375 10 false *a 1.792,3.458 2.167,3.844 0.375,0.385 10 false *b 2.229,2.354 2.552,2.625 0.323,0.271 10 false *c 1.021,4.448 1.323,4.667 0.302,0.219 10 false *2 2.24,4.448 2.531,4.667 0.292,0.219 10 false *1 2.698,0.229 3.01,0.427 0.313,0.198 10 false *3 2.25,2.948 2.573,3.219 0.323,0.271 10 false *c
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Piston Ring Expander
*a Code Mark (T)
*b Code Mark (2T)
*c Paint Mark
V100135

Upward


Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring so that the paint marks are positioned as shown in the illustration.

NOTICE:
·

Install the No. 1 compression ring with the code mark (T) facing upward.

·

Install the No. 2 compression ring with the code mark (2T) facing upward.

·

Paint marks can only be checked on new compression rings. When reusing compression rings, check each compression ring profile in order to install them into the correct positions.




d.
A331707C02
2.583,1.333 3.042,1.531 0.458,0.198 10 false 45° 0.948,2.344 1.26,2.5 0.313,0.156 10 false *1 2.375,0.938 2.688,1.094 0.313,0.156 10 false *2 2.208,2.344 2.521,2.5 0.313,0.156 10 false *3 0.948,1.094 1.26,1.25 0.313,0.156 10 false *4 0.698,1.708 1.01,1.865 0.313,0.156 10 false *a
*1 No. 1 compression ring and Oil Ring Expander
*2 No. 2 compression ring
*3 Upper Side Rail
*4 Lower Side Rail
*a Engine Front


Position the piston ring set so that the ring ends are as shown in the illustration.

HINT:

Perform "Inspection After Repair" after replacing the piston ring.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 11711 4.INSTALL CRANKSHAFT BEARING

a.
A290645C04
0.417,2.365 0.833,0.833 true 0.552,2.042 0.792,2.26 0.24,0.219 10 false A 0.906,0.729 1.219,0.927 0.313,0.198 10 false *a
*a Vernier Caliper


Install the crankshaft bearing (except No. 3 journal).

i.

Install the crankshaft bearing to the cylinder block sub-assembly.

HINT:

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.



ii.

Using a vernier caliper, measure the distance between the cylinder block sub-assembly edge and the crankshaft bearing edge.

Dimension (A):

0.5 to 1.0 mm (0.0197 to 0.0394 in.)


NOTICE:

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




b.
A162987C20
0.667,2.417 0.333,1.083 true 0.802,2 1.042,2.229 0.24,0.229 10 false A 1.99,2.01 2.188,2.198 0.198,0.188 10 false B 0.135,1 1,1.469 0.865,0.469 10 false *a
*a Vernier Caliper


Install the crankshaft bearing (for No. 3 journal).

i.

Install the crankshaft bearing to the cylinder block sub-assembly.

HINT:

Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.



ii.

Using a vernier caliper, measure the distance between the cylinder block sub-assembly edge and the crankshaft bearing edge.

Difference between (A) and (B):

0.5 mm (0.0197 in.) or less


NOTICE:

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




c.

Install the crankshaft bearing.

i.

Install the crankshaft bearing to the crankshaft bearing cap.


ii.
A151016C13
2.521,2.177 2.406,2.177 2.406,2.177 2.198,2.531 false 0.781,2 2.219,2.271 1.438,0.271 10 false *a 0.729,2.906 0.865,3.073 0.135,0.167 10 false A 2.052,2.906 2.188,3.073 0.135,0.167 10 false B 2.573,2.063 3.146,2.417 0.573,0.354 10 false *b
*a Mark 1, 2, 3, 4 or 5
*b Vernier Caliper


Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and the crankshaft bearing edge.

Difference between (A) and (B):

0.5 mm (0.0197 in.) or less


NOTICE:

Do not apply engine oil to the crankshaft bearings or the contact surfaces.




Hide 11791 5.INSTALL UPPER CRANKSHAFT THRUST WASHER

a.
A150982C09
1.313,1.302 1.26,1.875 1.26,1.875 1.542,1.479 true 1.146,1.906 1.844,2.063 0.698,0.156 10 *a
*a Oil Groove


Install the 2 upper crankshaft thrust washers to the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


b.

Apply engine oil to the upper crankshaft thrust washers.


Hide 13411 6.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper crankshaft bearings and install the crankshaft to the cylinder block sub-assembly.


b.

Apply engine oil to the lower crankshaft bearings.


c.
A296528C02
0.604,2.625 1.875,3.021 1.875,3.021 3.135,2.625 false 1.26,2.635 1.875,3.021 1.875,3.021 2.469,2.625 false 1.875,3.021 1.875,2.635 false 1.813,3.063 2.073,3.26 0.26,0.198 10 *a
*a Number mark
V100135

Engine Front


Examine the number marks and install the crankshaft bearing caps to the cylinder block sub-assembly.


d.

Apply a light coat of engine oil to the threads and under the heads of the crankshaft bearing cap set bolts.


e.
A205910

Temporarily install the 10 crankshaft bearing cap set bolts.


f.
A205917C01
1.969,2.396 3,2.552 1.031,0.156 10 *a
*a Less than 5 mm (0.197 in.)


Push on the crankshaft bearing cap with your hand until the clearance between the crankshaft bearing cap and cylinder block sub-assembly is less than 5 mm (0.197 in.).


g.
A151024

Using a plastic hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


h.

Install the crankshaft bearing cap set bolts.

NOTICE:

The crankshaft bearing cap set bolts are tightened in 2 progressive steps.



i.

Step 1:

i.
A297212N02
1.708,0.406 1.865,0.604 0.156,0.198 10 1 0.406,0.479 0.615,0.677 0.208,0.198 10 8 1.01,0.427 1.219,0.625 0.208,0.198 10 4 2.448,0.427 2.656,0.625 0.208,0.198 10 6 2.958,0.427 3.167,0.625 0.208,0.198 10 10 0.469,1.635 0.677,1.833 0.208,0.198 10 7 0.979,1.719 1.188,1.917 0.208,0.198 10 3 1.719,1.75 1.927,1.948 0.208,0.198 10 2 2.438,1.74 2.646,1.938 0.208,0.198 10 5 2.969,1.708 3.177,1.906 0.208,0.198 10 9

Uniformly tighten the 10 crankshaft bearing cap set bolts in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



j.

Step 2:

i.
A101478C79
2.083,0.75 2.573,0.479 true 1.271,0.427 1.583,0.698 0.313,0.271 10 false *b 2.625,0.375 2.938,0.74 0.313,0.365 10 false *a
*a Paint Mark
*b 90°
V100136

Engine Front


Mark the front of the crankshaft bearing cap set bolts with paint.


ii.

Tighten the crankshaft bearing cap set bolts by 90° in the order shown in step 1.



k.

Check that the paint marks are now at a 90° angle to the front.


l.

Check that the crankshaft turns smoothly.


m.

Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.

Install the connecting rod bearings to the connecting rods and connecting rod caps.


b.
A151017C19
0.354,2.698 0.667,1.667 true 1.958,2.49 2.104,2.646 0.146,0.156 10 false A 2.958,2.49 3.104,2.646 0.146,0.156 10 false B 0.74,1.563 1.292,1.906 0.552,0.344 10 false *a
*a Vernier Caliper


Using a vernier caliper, measure the distance between the edges of the connecting rod and connecting rod bearing, and the connecting rod cap and the connecting rod bearing.

Difference between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:

Do not apply engine oil to the connecting rod bearings or the contact surfaces.



Hide 8.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.


b.
A331707C02
2.583,1.333 3.042,1.531 0.458,0.198 10 false 45° 0.948,2.344 1.26,2.5 0.313,0.156 10 false *1 2.375,0.938 2.688,1.094 0.313,0.156 10 false *2 2.208,2.344 2.521,2.5 0.313,0.156 10 false *3 0.948,1.094 1.26,1.25 0.313,0.156 10 false *4 0.698,1.708 1.01,1.865 0.313,0.156 10 false *a
*1 No. 1 compression ring and Oil Ring Expander
*2 No. 2 compression ring
*3 Upper Side Rail
*4 Lower Side Rail
*a Front of Engine


Position the piston ring set so that the ring ends are as shown in the illustration.


c.

Confirm that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

A321517C02
3.542,0.885 3.854,1.083 0.313,0.198 10 false *c 1.531,0.708 1.844,0.906 0.313,0.198 10 false *a 3.563,2.344 3.875,2.542 0.313,0.198 10 false *d 4.229,1.813 4.542,2.01 0.313,0.198 10 false *b
*a Press around the circumference *b Ring End
*c Correct *d Incorrect (Ends of the oil ring expander are overlapping)


NOTICE:
·

After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.

·

If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.

·

If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.




d.
A311822C02
0.865,2.781 2.49,4.063 false 1.25,3.781 0.865,2.781 0.865,2.781 2.365,2.969 false 0.656,2.667 0.969,2.865 0.313,0.198 10 false *a
*a Front Mark


Using a piston ring compressor, push the correctly numbered piston and connecting rod into the cylinder with the front mark of the piston facing forward.

NOTICE:
·

When inserting the piston sub-assembly with connecting rod, do not allow it to make contact with the No. 1 oil nozzle sub-assembly.

·

Match the numbered connecting rod cap with the connecting rod.




e.
A205918C03
1.25,0.146 1.313,0.146 1.313,0.146 1.469,0.74 false 1.083,0.063 1.792,0.229 0.708,0.167 10 *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction.


f.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.


g.

Install the connecting rod bolts.

NOTICE:

The connecting rod bolts are tightened in 2 progressive steps.



h.

Step 1:

i.
A205915E04
0.409,0.301 0.788,0.485 0.378,0.184 10 SST 0.784,0.387 0.913,0.387 0.913,0.387 1.188,0.541 false

Using SST, alternately tighten the connecting rod bolts of the connecting rod cap in several steps.

SST
09205-16011  

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



i.

Step 2:

i.
A101478C80
2.063,0.75 2.375,0.448 false 1.281,0.385 1.635,0.563 0.354,0.177 10 false *b 2.417,0.302 3.229,0.479 0.813,0.177 10 false *a
*a Paint Mark
*b 90°
V100136

Engine Front


Mark the front of the connecting rod bolts with paint.


ii.

Tighten the connecting rod bolts by 90° as shown in the illustration.



j.

Check that the crankshaft turns smoothly.


k.

Check the connecting rod thrust clearance.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY


Hide 12211 9.INSTALL NO. 1 VENTILATION CASE

a.
A215737C02
1.323,2.854 1.708,3.042 1.708,3.042 1.875,3.042 false 1.188,1.615 1.375,1.927 1.375,1.927 1.521,1.927 false 0.938,3.177 1.375,3.396 0.438,0.219 10 false A-A 0.427,2.427 0.698,2.719 0.271,0.292 10 false *c 1.927,2.99 2.292,3.281 0.365,0.292 10 false *b 2.75,0.5 2.958,0.76 0.208,0.26 10 false A 1.969,0.51 2.188,0.75 0.219,0.24 10 false A 1.552,1.865 1.823,2.177 0.271,0.313 10 false *a
*a Seal Packing
*b 2.0 to 3.0 mm (0.0787 to 0.118 in.)
*c 5.0 mm (0.118 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Seal Packing Diameter Distance from Inside Edge of Cover to Center of Seal Packing
2.0 to 3.0 mm (0.0787 to 0.118 in.) 5.0 mm (0.118 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the No. 1 ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.

for Type A:

i.
A150902

Install the No. 1 ventilation case with the 6 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.

for Type B:

i.
A374058

Install the No. 1 ventilation case with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)