Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › CYLINDER HEAD › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0294293 CYLINDER HEAD A

8NR-FTS ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11155A 1.REPLACE RING PIN

HINT:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A352862C01
0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 2.323,3.115 2.635,3.271 0.313,0.156 10 false *b
*a Cylinder Head Sub-assembly Top Side
*b Protrusion Height


Using a plastic hammer, tap in new ring pins to the cylinder head sub-assembly.

Standard Protrusion Height:

3.0 to 5.0 mm (0.118 to 0.197 in.)



Hide 2.REPLACE STUD BOLT

a.

w/ Stud Bolt:

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


i.
A352689

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 3.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A352691N01
1.385,1.292 0.615,0.344 0.615,0.344 1.354,0.656 true 0.344,0.271 0.802,0.469 0.458,0.198 10 false SST

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A352712

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Intake Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.40492 to 0.40575 in.)


New Guide Bush Selection Chart:
Bush Size Bush Outer Diameter
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


HINT:
·

If the intake valve guide bush bore diameter is more than 10.306 mm (0.40575 in.), machine the intake valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.40689 to 0.40772 in.) to install an O/S 0.05 intake valve guide bush.

·

If the intake valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.40772 in.), replace the cylinder head sub-assembly.




e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A352713C01
1.094,1.302 0.51,0.302 0.51,0.302 1.115,0.729 true 3.167,0.885 3.344,1.052 0.177,0.167 10 false *a 0.25,0.208 0.708,0.406 0.458,0.198 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.6 to 10.0 mm (0.378 to 0.394 in.)



h.
A352714

Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the specified oil clearance.

Standard Oil Clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 4.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



c.
A352692N01
2.063,1.115 1.656,0.51 1.656,0.51 1.823,0.563 true 1.375,0.469 1.833,0.667 0.458,0.198 10 false SST

Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A352715

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard Exhaust Valve Guide Bush Bore Diameter:

10.285 to 10.306 mm (0.40492 to 0.40575 in.)


New Guide Bush Selection Chart:
Bush Size Bush Outer Diameter
STD 10.333 to 10.344 mm (0.40681 to 0.40724 in.)
O/S 0.05 10.383 to 10.394 mm (0.40878 to 0.40921 in.)


HINT:
·

If the exhaust valve guide bush bore diameter is more than 10.306 mm (0.40575 in.), machine the exhaust valve guide bush bore to a dimension of 10.335 to 10.356 mm (0.40689 to 0.40772 in.) to install an O/S 0.05 exhaust valve guide bush.

·

If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is more than 10.356 mm (0.40772 in.), replace the cylinder head sub-assembly.




e.

Heat the cylinder head sub-assembly to between 80 and 100°C (176 to 212°F).


f.

Place the cylinder head sub-assembly on wooden blocks.

CAUTION:

Be sure to wear protective gloves.



g.
A352716C01
2.177,1.146 1.708,0.615 1.708,0.615 1.927,0.615 true 0.969,0.958 1.281,1.115 0.313,0.156 10 false *a 1.427,0.573 1.885,0.771 0.458,0.198 10 false SST
*a Protrusion Height


Using SST and a hammer, tap in a new exhaust valve guide bush to the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height:

9.6 to 10.0 mm (0.378 to 0.394 in.)



h.
A352717

Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the specified oil clearance.

Standard Oil Clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)