Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › CYLINDER BLOCK › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0294294 CYLINDER BLOCK A

8NR-FTS ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE RING PIN

HINT:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A353042C01
0.052,0.083 0.365,0.24 0.313,0.156 10 false *a 2.26,3.167 2.573,3.323 0.313,0.156 10 false *b
*a Top Side
*b Protrusion Height


Using a plastic hammer, tap in the ring pins to the cylinder block sub-assembly.

Standard Protrusion Height:

6.5 to 7.5 mm (0.256 to 0.295 in.)



Hide 2.REPLACE STUD BOLT

HINT:

If the stud bolt is deformed or its threads are damaged, replace it.


a.
A353043C01
0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 2.073,3.948 2.844,4.146 0.771,0.198 10 false *c 2.083,3.49 2.854,3.688 0.771,0.198 10 false *b 2.604,3.667 3.375,3.865 0.771,0.198 10 false *d
*a LH Side
*b 14 mm (0.551 in.)
*c 13 mm (0.512 in.)
*d 29 mm (1.14 in.)


Using an E8 "TORX" socket wrench, install the stud bolts to the cylinder block sub-assembly as shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 3.REPLACE STRAIGHT PIN

HINT:

It is not necessary to remove the straight pins unless they are being replaced.


a.

Using a plastic hammer, tap in the straight pins to the cylinder block sub-assembly.

A353044C01
0.646,1.625 1.563,1.625 true 1.438,0.813 3.021,0.813 3.021,0.813 2.438,1.813 true 3.49,3.615 4.031,3.615 true 1.406,3.25 2.844,2.75 2.844,2.75 2.76,3.563 true 4.073,0.719 5.469,0.469 5.469,0.469 6.083,1.854 true 0.823,0.135 1.135,0.292 0.313,0.156 10 false *a 3.979,0.135 4.292,0.292 0.313,0.156 10 false *b 0.917,2.354 1.229,2.51 0.313,0.156 10 false *c 3.979,2.375 4.292,2.531 0.313,0.156 10 false *d 6.521,4.979 6.833,5.135 0.313,0.156 10 false *e 0.5,1.552 0.656,1.75 0.156,0.198 10 false A 0.719,5.594 1.49,5.792 0.771,0.198 10 false *g 1.219,4.865 1.99,5.063 0.771,0.198 10 false *f 3.083,0.75 3.24,0.948 0.156,0.198 10 false B 0.75,4.313 0.906,4.51 0.156,0.198 10 false A 1.844,4.854 2,5.052 0.156,0.198 10 false B 2.25,5.146 3.021,5.344 0.771,0.198 10 false *h 1.844,5.615 2.615,5.813 0.771,0.198 10 false *i 3.323,3.563 3.479,3.76 0.156,0.198 10 false B 3.677,5.042 4.448,5.24 0.771,0.198 10 false *j 2.896,2.635 3.052,2.833 0.156,0.198 10 false C 3.198,4.646 3.354,4.844 0.156,0.198 10 false C 5.49,0.323 5.646,0.521 0.156,0.198 10 false D 4.615,4.802 4.771,5 0.156,0.198 10 false D 4.583,5.615 5.354,5.813 0.771,0.198 10 false *l 5.063,5.115 5.833,5.313 0.771,0.198 10 false *k 3.167,5.604 3.938,5.802 0.771,0.198 10 false *g
*a Front Side *b Bottom Side
*c Rear Side *d LH Side
*e Protrusion Height *f 36 mm (1.42 in.)
*g 10 mm (0.394 in.) *h 12 mm (0.472 in.)
*i 4 mm (0.157 in.) *j 22 mm (0.866 in.)
*k 18 mm (0.709 in.) *l 8 mm (0.315 in.)


Standard Straight Pin:
Item Protrusion
Pin (A) 18.5 to 19.5 mm (0.728 to 0.768 in.)
Pin (B) 5.5 to 6.5 mm (0.217 to 0.256 in.)
Pin (C) 11.5 to 12.5 mm (0.453 to 0.492 in.)
Pin (D) 8.0 to 10.0 mm (0.315 to 0.394 in.)